curve fitting test 中文意思是什麼
curve fitting test
解釋
適線檢驗-
( 2 ) based on indoor test, two typical soft rock of brecciated mudstone and siltstone in luohu jiancheng district is carried systemically though interior rheological testing ; moreover combining with preceding studying results of rock rheological constitutive model, rheological numerical constitutive model suited to rock mass mechanics characteristics and stratum structure of luohu fracture zone, and numerical parameters of the model are processed with studying of curve fitting
（ 2 ）立足於室內試驗，對羅湖建成區兩種典型的軟弱巖石?含角礫泥巖和粉砂巖進行系統的室內流變試驗研究，又結合前人對巖石流變本構模型的研究成果，分析並確定了適合羅湖破碎帶巖體力學特性及地層構造特徵的流變計算本構模型，並對該模型的計算參數進行了曲線擬合研究。 -
After looking up a large amount of native and foreign information, the materials used in the experiment were as follows : ptfe base, graphite filler, molybdenum disulfide filler, copper powder filler, carbon fiber and so on. the experimental method is that the formula was designed according to uniform experimental method, the relationship between formula and frictional property was found with spline function and then the representative test points were chosen from fitting curve to make verification test for optimization. the preparative technique of solid lubricant is cold - press sintering method
經過查閱大量國內外文獻資料后確定原料為：聚四氟乙烯樹脂為基體，加入石墨、二硫化鉬、銅粉、碳纖維等填料；試驗方法為：根據均勻試驗方法設計配方，用樣條函數找出配方與摩擦性能的關系，然後在擬合曲線上選取具有代表性的試驗點進行驗證試驗，達到優化的目的；制備工藝：冷壓燒結法制備固體潤滑劑。 -
It achieves full test automation from calibrating, running, failure diagnosis and data processing, which establish it an intelligent test system. in the software, a curve fitting program which based on the system ' s principle which can greatly improve the calibration precision and a safl mathematical statistics program for the test data are made
在試驗系統軟體設計上，結合試驗機原理，採用基於原型函數的動態標定數據曲線擬合提高了載荷標定的精度；通過對比各種曲軸試驗數據的處理方法，同時考慮在實際運用中的效果，計算機統計採用了疲勞極限統計分析（ safl ）法。 -
Finally, the paper realize the convenient dialog interface and hydraulic machine ' s test data processing mainly introduces, analyses the multinomial fitting and spling interpolation mathematics models and solves the solution and drawing of constant efficiency value curve and 95 % confining curve in comprehensive specific property curve
實驗臺的軟體系統實現了友好的人機對話，實驗數據處理部分主要介紹、分析了多項式擬合模型和三次b樣條插值模型，實現了模型轉輪綜合特性曲線中等效率曲線的求解與繪制以及95出力限制線的繪制。 -
Adopting the deformation harmony theory, the numeric calculation of the curve of load versus settlement is made. the fitting results between the calculated curve of load - settlement and the measured one of piles with different construction process are illustrated. hence, under the condition of few or no static load test data, the performance of bearing capacity of single bored pile in loess may be predicted utilizing indexes of shear wave velocity, static cone penetration test and modification coefficient of depth, so it is remarkable to reduce the blindness of preliminary design of pile
通過室內試驗及原位測試指標進行理論計算與現場實測值的對比，筆者引入了施工工藝修正系數k _ （ c1 ）和k _ （ c2 ）及深度修正系數，使理論計算值與現場實測值具有良好的一致性，進而通過變形協調理論對荷載?沉降曲線進行數值計算，並用不同施工工藝的實例說明了理論計算荷載?沉降曲線與實測荷載?沉降曲線的擬合效果，從而達到可在不做靜載荷試驗或少做靜載荷試驗的情況下通過剪切波速和靜力觸探試驗指標以及施工工藝修正系數等預測黃土地基中鉆孔灌注樁承載性狀，這對于工程初步設計中減少設計的盲目性具有十分重要的現實意義。 -
In contrast to phase separation ( curve - fitting ) approaches which are largely mathematical, phase resonance testing is a physical technique. when a structure is vibrating in a normal mode, the undamped natural frequency and normal - mode shap of the structure are directly measured. in the classic phase resonance testing, the test data processing is simpler and the results are more accuracy
相對于相位分離法來說，相位共振法是一種比較直觀的物理識別方法，在結構做「純模態」振動時，通過物理測量直接獲得模態參數;試驗數據處理工作量小，且精度一般比單輸入系統高。
分享友人