curve modeling 中文意思是什麼
curve modeling
解釋
曲面模擬-
This paper put forward the optimized methods include reconstructing the characteristic curve by reasonable use of the adjust tools and analyse tools of the modeling software, admeasuring the automotive model surface correctly, simulating the breaking surface and creating the surface in the right turns which is good for modeling a smooth and exactitude surface. at last, after the correct analysis of the factors which are effect to the surface construction, a smooth and exactitude surface of the similar diamond concept car has been constructed by using the right optimize method
本文通過合理利用反求軟體中的造型工具和分析工具，正確劃分反求模型的造型區域，使用正確的曲面造型方法，對反求曲面的特徵網格線進行二次優化，並對突變曲面進行擬合再生成處理及建立合理的曲面生成順序等方法，最終獲得了仿型度和光順度都很高的反求曲面。 -
Abstract : based on the present possessed experimental data of steels with their different major chemical composition, this article formularized the calculation of linear expansion coefficients of fine carbon steels and low alloy constitutional steels through a series of alternate analysis, generalized statistics, curve superimposition and mathematical modeling
文摘:對優質碳素結構鋼和幾類低合金結構鋼，在現有實驗數據的基礎上，通過迭代分離、綜合統計、圖象分析和數學擬合，得出按鋼的主要化學成分確定其線膨脹系數的計算關系。 -
This thesis gives a brief account of the basic theories of software engineering and computer graphics, of the data structure of individual component modeling, of the design of the software structure and of the method of realizing software. meanwhile, this thesis put more emphasis on the exploration of the arithmetic of the delaunay triangle network, nurbs curve integration, the filling - in arithmetic of triple - tree, and the arithmetic based on the scan - line arithmetic and the filling - in of complex section
文章介紹了關于軟體工程學與計算機圖形學的基本理論及其各組件模型的數據結構、軟體結構設計與軟體實現的技術方法，並重點討論了基於約束條件的delaunay三角網格化演算法、 nurbs （非均勻有理b樣條）曲面擬合、三叉樹等值線填充演算法和基於掃描線的復雜剖面填充演算法。 -
The dissertation proposes originally the idea of decomposing the time - variant load to solve this problem. first, the time - variant load is decomposed into the time - variant load characteristic and the time - variant load model due to the modeling method. second, the multi - curve approximation method is proposed to identify the load parameters, which to a great extent, reduces the effects on the time - variation of the load model from modeling method
針對負荷的時變性，論文首次提出了將負荷時變性分解的思想，首先將負荷的時變性分解為負荷特性的時變性和由建模方法引起的負荷模型的時變性，然後提出了多曲線擬合參數辨識方法，很大程度上消除了建模方法引起的負荷模型的時變性。 -
Finally, when a 00, the limt situations for the developable modeling and surface development above are all disscussed and compared with those on bezier curve. the programs of the above methods und algorithms are developed, which shall be used in the system of developable surface modeling for cad / cam
Zier曲線上可展曲面造型方法和曲面展開演算法，均給出了當0時的極限，並與b ? zier曲線的情形作了分析和比較。這些方法和演算法均應用於實例在計算機上得以實現。 -
Morphing is the continuous smooth and natural transformation of a source object into a target object, where the object can be a numerical image, curve, surface, mesh, etc. morphing has very wide use in many areas, such as computer graphics, animation design, industrial modeling, science computation visualization, film stunt, etc. this paper makes researches on the morph of compatible planar triangulations and that of planar polygons, and the main results are as follows : 1 ) morph of compatible planar triangulations : this paper presents a convexity - preserving method for morphing compatible planar triangulations with different convex boundaries
變形，是指從初始物體到目標物體的連續、光滑、自然的過渡（這里的物體可以是數字圖像、曲線、曲面、網格等） 。變形在許多領域有著十分廣泛的應用，如計算機圖形學、動畫設計、工業造型、科學計算可視化、電影特技等。本文對同構平面三角網格的變形和平面多邊形的變形進行了研究，主要的研究結果如下： 1 ）同構平面三角網格的變形：提出了具有不同凸邊界的同構平面三角網格的保凸變形方法。 -
This process is as follows : firstly, the data of different section contour and of section line have been obtained by reverse - engineering ; secondly, non - uniform b - spline approximation algorithm is used to fit the discrete data ; then the data have been optimized and reduced by adopting adaptive sampling of key points of the fitted curve based on vertical distance, sequently the adaptive sampling data is transformed into the format of the. ibl file of the famous 3 - d design software pro / e. therefore we reconstruct the surface and a model is generated ; lastly, the effectiveness of the adopted algorithm and modeling approach are demonstrated by the experiments
建模型的過程中，首先運用逆向工程測量方法，獲得曲面物體上不同截面輪廓線的測量數據點列，接著對測量數據點進行平滑處理，用最小二乘法求解基於數據點列的控制多邊形，以非均勻三次b樣條曲線擬合截面輪廓曲線；然後利用基於垂距的數據采樣演算法，對擬合曲線上的數據點進行重新采樣，達到優化數據點的分佈及減少描述曲線數據量的目的。 -
The study demonstrated that linear visco - elastic parameters of rheological models built by theoretical modeling methods were constant while nonlinear visco - elastic parameters were not constant and changed as stress level changed and that visco - plastic parameters determined the shape of stress - strain curve
研究表明：運用模型理論建立的流變模型的線性粘彈性參數在低應力水平下是惟一的，但非線性粘彈性參數不惟一，並隨應力水平的變化而變化，而粘塑性參數的大小決定了應力應變等時曲線的形狀。 -
In this paper we integrate the theoretical analysis with opnet modeling and simulation to analyze the key factors that affect the throughput performance metric of the aos protocol. with the throughput curve we optimize the protocol configuration to direct the applications of the protocol to space missions
本文採用理論分析與opnet軟體建模模擬相結合的方式分析影響aos協議包業務吞吐量性能指標的關鍵因素，並根據得到的吞吐量曲線優化協議配置參數，得到的結論可以指導協議在空間任務中的應用。 -
The program of data processing in determination of percent released of pharmaceutical preparation was developed ; two modules included in this program are connected but independence each other, one module calculate percent released, one module regress equation ; determination of percent released of pharmaceutical preparation, comparison of released curve in one reference frame and modeling mathematics model were realized by running this program. the program of formulation optimization based on artificial neural network was compiled to solve the nonlinear problem in formulation optimization. provided parameters were used to predict the released amount of a set of formulations
簡便，其計算結果與現有其他程序計算結果基本一致：開發固體制劑體外溶出試驗數據處理程序，程序運行時分為計算累積釋放百分率和優選最佳數學模型兩個相互連接又各自獨立的環節，實現了累積釋放百分率的自動計算，同一坐標系下釋放曲線的直觀比較，常用數學模型的擬合；開發基於人工神經網路的處方優化系統，解訣處方優化這一多目標、非線性優化問題，利用符合擬合精度的訓練結果預測給定處方的釋放度，預測結果與實驗結果基本相近。 -
In some time - critical situation, continuous ssi is computation bottleneck of some solid modeling system. conventional approach for solving continuous ssi often uses intersection algorithm iteratively without taking the characteristic of the surface into account to simplify computation. the dissertation analyzes the intersect curve structure of continue surface, from the point of intersect curve ' s evolution, it describes the relationship between topology of offset surface intersect curve and topology transmit point ( ttp )
等距曲面和運動曲面在cad cam領域中有著重要的應用，在一些時間敏感場合例如數控加工動態模擬，等距曲面和運動曲面等連續變化曲面求交運算已成為這些系統的計算瓶頸，連續變化曲面求交問題的通常解法是採用曲面求交演算法反復迭代計算交線，沒有考慮連續變化曲面交線之間的相似性進行求交簡化，效率上一直不能有很大的提高。 -
In the course of modeling, we present multi - step generalized gradient method and multi - stage curve fitting technique, prove convergence of multi - step generalized gradient method by using differential equation stable theory, analyze the error of multi - stage curve fitting technique by using inner space, creat knowledge base of water network system by using the maximum subordinate principle of and near - select principle of pattern recognition. at last we make the optimal running scheme of water network system based on heuristic search technique of artificial intelligence and global feedback immediate coordination method of large scale system theory
在建立系統模型的過程中，提出了多步廣義梯度法和多層曲線擬合的建模方法，並用微分方程穩定性理論證明了多步廣度梯度法收斂性，用內積空間的有關知識對多層曲線擬合進行誤差分析;應用模糊數學中的最大隸屬度原則和模糊識別中的擇近原則和人工智慧中狀態空間表示法建立注水系統的知識庫;用人工智慧中的啟發式搜索技術和大系統理論中的具有全局反饋的直接協調法制定注水系統的優化運行方案。 -
This paper studies the rational b - splines curves with prescribed poles and surfaces for the first time, and studies the properties of this new surface modeling. the result indicate that this modeling not only have the property of geometric modeling, but also have the agility and availability, and score the singular of curve
本文首次構造了指定極點的有理b樣條曲線曲面，並深入研究了這種新穎曲面模型的性質，結果表明該有理曲面模型不僅具有幾何造型的特點，而且更靈活、更有效，並能刻畫曲線的奇性等固有特性 -
Trapezoid curve method is adopted for frequency control of stepper motor. and a rough speed control method of servo motor is developed. kinematics modeling of rover in manipulation is presented
控制系統軟體部分採用梯形曲線對步進電機進行升降頻控制，同時實現了對舵機的近似速度控制。 -
In the first chapter, we narrate the characteristic of convertible bond, give some clues about development and actuality of the market and its pricing theory ; in the second chapter, we introduce modeling idea and some material problems in the model in detail, draw the yield curve which is very important to the model by spline method ; in the third chapter, we first explain the basic idea and convergent speed of monte carlo method, then, give the mathematical description for financial market, prove equivalence of non - arbitrage market, existence of risk neutral probability measure in the market and the price process of underlying asset is a martingale ; in the forth section, we introduce how to simulate stock price path by monte carlo method in detail, based on foregoing result, we prove the path is a martingale, thereby, the model is logical
本文第一章先對可轉債的特點、市場發展和現狀及其定價理論的發展和現狀作一概述;第二章詳細介紹了建模思想和模型中的一些具體問題，利用spline方法繪出了在模型中具有重要作用的收益曲線;第三章首先敘述了montecarlo方法的基本思想和有關其收斂速度的一些性質，然後從數學的角度給出了對金融市場的描述，證明了市場無套利、市場存在風險中性概率測度及標的資產價格過程為鞅的等價性;在第四節中，對用montecarlo方法模擬的帶跳股價路徑作了詳細介紹，並利用前兩節的結論證明了模擬的帶跳股價路徑為一個鞅過程，從而保證了模型在理論上的合理性。 -
To fulfill the need of the application of rp technique in medical domain, reverse cad modeling from medical cross sections is systematically studied in this dissertation. firstly, some algorithms related to the research of this dissertation are studied. new algorithms for orientation and inclusion test for simple polygon, an error constrained automatic faring algorithm for b - spline curve and a theorem regarding the termination criterion for subdivision of triangular bezier patch are proposed
本文針對rp技術在醫學領域應用的需要，系統研究了基於醫學斷層輪廓數據的反求cad建模理論和方法： （ 1 ）在基礎演算法研究部分，提出了簡單多邊形方向及點在多邊形內外判斷的新方法、三角b zier曲面片離散的誤差控制定理和一種帶誤差約束的b樣條曲線的自動光順方法； （ 2 ）提出了一種基於相鄰層輪廓相似性的醫學斷層輪廓數據曲面重構方法； （ 3 ）提出了一種稱為「虛擬測量」的曲面模型處理方法。 -
The principle of the predigestion in geometry modeling is omitting the function part and the non - load - carrying process structure, and to the big and transition arc, the curve is replaced by straight line using the thought of curve and free - surface segmentation. the physical characteristic of the digital model reflect on remaining the main mechanical characteristic of the objects. the shell element model is used in strength analysis, stiffness analysis and dynamic analysis
文中幾何建模的簡化原則是，略去功能件和非承載的工藝結構，對于大圓弧和過渡圓弧，以曲面分塊和曲線分段的思想進行適當的以直代曲;數模的物理特性反映在最大限度地保留對象的主要力學特性;在強度、剛度和動態分析中採用殼元模型，輕量化設計中採用梁元模型;材料特性根據所用材料定義其主要性能參數。 -
Thirdly, the principles of nurbs curve and surface are used to the modeling of complex object, and a protruding quadratic programming algorithm for reconstructing reference points of nurbs curve
第三，採用了nurbs曲線、曲面技術對復雜目標建模，給出了反求nurbs曲線控制點的凸二次規劃演算法。 -
Firstly, we make numerical modeling analysis with finite element method and eliminate the effect of tunnel - cavity, translate the apparent resistivity curve of advanced detection in tunnel into the curve in full space
首先利用有限元數值模擬技術分析並消除坑道空腔對視電阻率的影響，並將坑道超前探測視電阻率曲線轉化為全空間視電阻率曲線。 -
As the basic concept, the first step is to modeling by ug. there is different model between propeller and commonly hardware, so we must be use curve modeling, at the same time, characteristic modeling and entity modeling in the whole process. first, we apply offset data for spline fit curve, then scanner smooth curve face
首先在三維繪圖軟體ug中對螺旋槳及葉片進行三維建模，由於螺旋槳的造型不同於一般零件的cad造型，故在造型過程中同時採用了曲面造型，特徵造型和實體造型幾種方法，先由型值數據生成樣條曲線，再由樣條曲線掃掠生成平滑的曲面，最後通過圓整?延伸得到螺旋槳的三維模型。
分享友人