curves selected 中文意思是什麼

curves selected 解釋
被選擇的曲線
  1. In the top viewport, find the curves selected below and loft them together using the default options

    在俯視圖,找到下圖中所選曲線,用默認設置一起放樣。
  2. Repeat this step with the two curves just above the ones selected here

    對所選曲線上面的兩條也按上述步驟同樣處理。
  3. For the bands selection of hyper spectral image, an algorithm called selected projection pursuit is established and a quick calculating method is developed, the calculating speed is increased 80 ( the bands number of hyperspectral image ) limes. the nonlinear principal curves is researched, it is the nonlinear expansion of pca

    針對高光譜圖像光譜波段的最優波段選擇問題,構造了選元投影尋蹤演算法,並為此建立了一種快速選元投影尋蹤演算法,使演算法的速度提高將近80倍(波段總數的倍數) 。
  4. The francies " hydro turbine models are induced, comprising of the linear model based on the model characteristic curves, the linear model based on the internal characteristics description, the nonlinear model based on four - quadrant characteristics and simply analytic nonlinear model. as a result of comparison of these models, it is believed that these models have different traits and the proper model should be selected according to the study purpose and known conditions

    歸納介紹了混流式水輪機的模型,包括基於模型綜合特性曲線的線性化模型、基於內特性描述的線性化模型、基於全特性曲線的非線性模型和簡單解析非線性模型等,對這些水輪機模型進行分析比較,認為它們的特點各有不同,應根據研究目的和已知條件來選擇合適的模型。
  5. First of all, the whole damage field curves with toughness that selected as the fatigue damage variable was measured, then on the basis of frame of nonlinear continuum fatigue damage theory, the expressive form of fatigue damage parameter was decided by means of the tested curve data, and a new nonlinear fatigue damage cumulative model was proposed

    摘要首先以韌性為損傷變量進行全域損傷曲線測試,以非線性損傷理論框架為基礎,用測試曲線數據確定損傷變量參數表達形式,得到非線性連續疲勞損傷模型。
  6. Samples for strontium isotopic screened were selected by way of the test of cathodoluminescence, observation of thin sections, and analysis of sr and mn. the mn / sr value of all samples presented in this paper are less than 2, and the cathodoluminescence is dull, however, the samples from the cambrian underwent diagenetic alteration to a certain degree, and the plotted points of the thickness and 87sr / 86sr value are somewhat discrete. the strontium isotope evolution curve drawn from the data with relatively low 87sr / 86sr value are consistent with other curves based on samples from different areas of the world, supporting the notion of global consistency of strontium isotope composition of marine carbonates

    根據鋸同位素地層學的基本原理,利用已有的鋸同位素演化曲線,筆者確定重慶秀山寒武系剖面寒武系底界、下一中寒武統界線和中一上寒武統界線都應適當下移;另外嘗試確定了重慶秀山寒武紀剖面一些關鍵點的年齡,累積厚度1380m處的年齡為503 ? 509ma ,累積厚度1900m處的年齡約為500ma ,這對秀山寒武系剖面下、中寒武統和中、上寒武統界線的確定具有參考價值。
  7. From the processing results of two well logging data, it can be roughly recognized that the selected well logging curves with multi - fractal characteristics are stack responses of the different sedimentary procedures

    通過對兩口井的地球物理測井曲線處理,可以初步看出,在選定的地球物理測井曲線中,其具多維分形特徵,不同的沉積過程相互疊加在原始測井曲線中。
  8. The systemic research on the algorithms and the correlative algorithms establish massive foundation for the application of quintic spline curves in nc machining. ( 3 ) until now, interpolation points have mostly been selected manually in an empirical way

    五次樣條插值演算法及其配套演算法的系統深入研究,為五次樣條曲線在數控加工技術領域中的應用奠定了堅實的演算法基礎。
  9. Turbojet engine is selected as propulsion system according to the practical situation. the work of this part ranges from design to characteristic analysis. the characteristic curves of engine in various situation are shown, which provides preparation for trajectory computation

    並對渦噴發動機從設計到特性分析做了大量的工作,給出發動機在不同工作狀態下的特性曲線,為進一步研究彈道設計提供了前期的準備工作。
  10. For every point on contour curves, the support area and support radius were first calculated based on actual distance of adjacent pixels, end points were obtained with linear interpolation technique ; next, the distance between point and its centroid of support area was used as feature strength to determine feature points candidate ; finally, those points with local maximum feature strength were selected as vertices of polygonal

    摘要首先基於相鄰像素間的歐氏距離計算出輪廓曲線上每一點的支持區域及支持半徑,用線性插值得到支持區域的端點;然後求得支持區域的質心,以曲線上的點和其相應的支持區域質心之間的距離作為特徵響應篩選出候選特徵點;最後將具有局部極大特徵強度的點作為多邊形的頂點。
分享友人