cutting clearance 中文意思是什麼

cutting clearance 解釋
后角
  • cutting : n 1 切斷，切下；切片；【園藝】扦插，插條；〈英國〉剪裁，（報紙等的）剪輯；（寶石等的）加工，琢磨...
  • clearance : n 1 清除，掃除，除去；解除。2 【林業】終伐；（伐去樹木后的）林間空地。3 出[入]港證；放行證；出入...
  1. This machine is applied to sawing thread clearance during the course of making from quarto to super - largedie cutting plate

    本機適合於四開到超大全張的各種模切版製作時線縫的鋸制。
  2. Research on the working orthogonal clearance of flying cutting tool machining worm wheel in radial feeding way

    飛刀徑向進給加工鍋輪工作后角分析
  3. In addition, over 500 clearance operations and inspections at district hygiene blackspots and grass - cutting at rural areas had been conducted

    同時亦在環境?生黑點及鄉郊地方進行了逾五百次清理、巡查或除草行動。
  4. The convenient handwheel adjustment of cutting edge clearance is rapid and precise as well

    矩形刀片，四個刃口均可使用，使用壽命長。
  5. Lands department would conduct two rounds of grass cutting and rubbish clearance at about 300 identified blackspots and clear 10 illegal hillside cultivation black spots ; and

    地政總署會在約三百個已確認的?生黑點進行除草及清理垃圾行動，並清除十個山邊非法耕種黑點；以及
  6. The lands department will step up inspection, clearance and grass - cutting at unallocated government land sites to eliminate mosquito breeding sites

    地政總署已在尚未批撥出的政府土地，進行檢查、清理及剪草，鏟除滋生蚊子的地點。
  7. Discussion again on principle effect of side clearance angle to cutting surface roughness

    鋸料角影響鋸切表面粗糙度機理再探
  8. Secondly, based on cutting edge geometric model and machining mode of mk6335a grinder, the rake face with constant normal rake angle and flank face with constant orthogonal clearance angle models of ball - end cutters are discussed. the cutting geometry angle parameters are solved and analyzed. moreover, the tool paths models of wheel which grinding are builded and the post - processing technique for coordination transfer is studied

    然後，基於刃口曲線模型、五軸數控磨床刃磨運動方式和微分幾何的直紋面概念，本文推導與建立了具有等法前角的前刀面和具有等主后角的后刀面的球頭立銑刀數學模型，並對球頭立銑刀的刀具角度如刃傾角、主前角、法后角、主偏角等參數進行了求解與分析。
  9. Be able to understand the cutting clearance with different die, and calculate the cutting clearance with the different thickness of the material

    能理解不同模具的切刀間隙，並根據不同的材料厚度計算出切刀間隙。
  10. Will conduct grass - cutting and site clearance on new black spots

    在新確認的黑點進行除草和清理行動。
  11. Will conduct by october 2003 grass - cutting and site clearance at a total of about 600 identified black spots

    二零零三年十月前，在約共
分享友人
分享到 Line

分享到臉書