decomposition temperature 中文意思是什麼

decomposition temperature 解釋
分解溫度
  • decomposition : n. 1. 分解，分析，溶解，還原（作用）。2. 腐朽，解體。
  • temperature : n. 1. 溫度，氣溫。2. 體溫。3. 〈口語〉發燒，高燒。
  1. Researching into tg - dt diagrams, we have concluded as follows : the initial decomposition temperature ( idct ) of polymer ( i ) is 220c and the first lost group ( flg ) ls carboxide ; the idct of polymer ( hi ) is 194cand the flg is - nh ; so the pyrolysis mechanisms of the two polymers are different

    對聚合物（ d和聚合物（ l11 ）的tg一ot研究表明:聚合物（ d的開始分解溫度為220 ，失去的第一個基團為> c = 0 ;聚合物（ 11工）的開始分解溫度為! 94oc ，先失基團為一陽，兩者的熱解機理不盡相同。
  2. Therrnogravimetric analysis at heating rates 5, 10, 15 and 20 c / min was used to study the decomposition kinetics of the pdms / pma ipn in ni and in air by using tg and dtg, and the upper limit of the temperature was 700 c. it was found that ipn began to decomposite at 350 c. the process of the thermal degradation was multiple steps, the curve of the rate of thermal decomposition had two peaks, one of which lied between 400 c ~ 420 c and the other lied between 500 c ~ 540 c, the result corresponded to the components of ipn

    在熱分解動力學研究中，通過在兩種氣氛中，分別以5 、 10 、 15和20 min四種升溫速率條件下，採用tg - dtg聯動測試， ipn材料在350開始熱分解。熱分解速率存在兩個峰值，一個分解峰值在400 420之間，另一個在500 540之間，這與ipn結構中包含兩組分相對應，同時發現當緩慢升溫時，特別是在空氣氣氛中，兩個分解峰減弱，熱分解趨向於一個連續過程。
  3. Combustion at high temperature causes decomposition to nitrogen and water.

    氨在高溫下燃燒分解成為氮和水。
  4. Temperature also affects the rate of decomposition and thus the nutrient flux rate.

    溫度還會影響分解的速度，從而影響養分流的速度。
  5. Begin with the comparation of two widely used methods producing the strontium titanate, the oxalate decomposition method shows its advantage hi the microstructure and future performance. the effect of caco3 is studied, and so is the effect of the donor dopant, such as nb2o5, y2o3 and la2o3. the dopant of tio2 is also considered, which involve ti / sr ratio, sintering temperature, oxygen partial pressure, donor dopant, grain growth and future electric performance

    從對比草酸鹽分解法和固相合成法這兩種制備srtio _ 3主晶相的方法開始，在予合成料的制備過程中分析了施主nb _ 2o _ 5 、 y _ 2o _ 3 、 la _ 2o _ 3以及caco _ 3所產生的影響；在tio _ 2摻雜的問題上，綜合考慮了ti / sr比、燒結溫度、氧分壓、施主摻雜、晶粒的微觀生長與成瓷后的元件宏觀電性能等之間的相互關系。
  6. The components, microstructure, luminousness, thickness and surface topography of the films were analysised via xrd, uv ? vis, xps, ellipsometric examination and stm. the photocatalytic properties of these fims are characterized by the decomposition rate of methylene blue or rhodamine b. the effect of sputtering power, temperature, o2 mass flow, bias, w - doping and sputtering time on photocatalytic properties are discussed

    採用x射線衍射儀、紫外-可見光分光光度計、 x光電子能譜儀、薄膜厚度測試儀及掃描探針顯微鏡等測試手段，研究分析了薄膜的組分、結構、透光率、膜厚和表面形貌等。
  7. The results indicated that the dimension, shape and purity of base material could meet the functional demand of solid lubricant ; the thermal decomposition temperature of ptfe resin exceeds 400 c, but organic and inorganic packing filler added in ptfe made the water absorption rate of composite material increased, melting temperature and decomposition temperature decreased, in the meanwhile oxidative decomposition reaction was accompanied ; polar groups such as c = o, c - o - c and so on in the carbon fiber surface is advantageous to increase compatibility with other components and interlayer shearing strength ; uniform design experimental method could help to find the relationship between formula and frictional property by relatively small tests. the developing trend of each formula ' s friction coefficient could be showed by fitting curve ; the friction coefficient with no copper powder or graphite in formula was relatively big. this fact showed that copper powder and graphite should be used cooperatively ; it was found that when the ratio of copper powder to graphite by weight is 15 : 60, 30 : 30 - 40 and 60 : 15 - 30 respectively, the friction coefficient was relatively small. the degree of crystallinity of pure ptfe reached maximum by air cooling and the abrasion loss also reached maximum among three ones ; at the same time, the abrasion loss of solid lubricant sample was also the biggest among three ones ; when solid lubricant matched with 45 # steel axle or gcrl5 steel axle, lubricant transfer film could be formed on metal surface, thus direct contact between the surface of metal friction pair rings was reduced. their working life was elongated extremely ; there was mainly much graphite, a little ptff, moo3, feso4, cus and so on in lubricant transfer film

    試驗結果表明：所選原料的尺寸、形狀及純度可滿足固體潤滑劑的性能要求；聚四氟乙烯樹脂熱分解溫度超過400 ，但在ptfe中加入無機填料會使復合材料吸水率提高，熔融溫度及分解溫度降低，且伴有氧化分解反應；碳纖維表面含有c = o及c - o - c等極性基團，有利於提高其與其它組分的相容性，提高層間剪切強度；均勻設計試驗方法能夠用較少的試驗次數找出配方與摩擦性能間的關系，擬合曲線基本能表示各配方的摩擦系數發展趨勢；配方中不加銅粉或不加石墨，其摩擦系數均較高，說明銅粉和石墨應該配合使用；當銅粉15份、石墨60份時，銅粉30份、石墨30 - 40份時，銅粉60 、石墨15 - 30份時，摩擦系數均具有較低值；純聚四氟乙烯樹脂在空氣冷卻時結晶度最大，磨損量也是三者中最大的；同時，固體潤滑劑試樣在空氣冷卻時的磨損量也是三者中最大的：不論是固體潤滑劑與45 #鋼軸配副或是固體潤滑劑鑲嵌入銅套后與gcr15鋼軸配副，在金屬表面均可形成潤滑轉移膜，從而減少金屬摩擦副表面間的直接接觸，大大延長其使用壽命;轉移膜中主要含有較多的石墨、少量聚四氟乙烯、 moo 。
  8. The project initiated by scientists from university of california and co - operated scientists from haibei research station, cas. the objectives of the experimental are to examine how the vegetation and soil in sites with low and high grazing intensity and with two habitat types ( meadow and shrubland ) respond to climate warming. the research will include plant community, phenology, growth allocation and soil temperature, soil nutrient availability, decomposition, and mineralization

    自1997年起，海北站與美國加利佛尼亞大學的科學家合作建立了32個greenhouse ，分別建在不同放牧強度下的高寒草甸和高寒灌叢中，研究的目的是探索植被和土壤在不同放牧強度下對氣候變暖的響應，其中包括植物群落、物候學、土壤溫度、土壤營養、分解和礦化作用等。
  9. The project initiated by scientists from university of california and co - operated scientists from haibei research station, cas. the objectives of the experimental are to examine how the vegetation and soil in sites with low and high grazing intensity and with two habitat types meadow and shrubland respond to climate warming. the research will include plant community, phenology, growth allocation and soil temperature, soil nutrient availability, decomposition, and mineralization

    自1997年起，海北站與美國加利佛尼亞大學的科學家合作建立了32個greenhouse ，分別建在不同放牧強度下的高寒草甸和高寒灌叢中，研究的目的是探索植被和土壤在不同放牧強度下對氣候變暖的響應，其中包括植物群落物候學土壤溫度土壤營養分解和礦化作用等。
  10. The performance of catalyst beds was experimentally studied. the influence on decomposition was investigated with changing the mass flux through the cross of the catalyst bed and the initial temperature of the catalyst bed. the experimental results were compared with those of the numerical simulation

    對過氧化氫催化床的催化性能進行了試驗研究，分析了催化床床載、催化床初始溫度對過氧化氫催化分解的影響，與一維情況下的數值模擬結果進行了對比。
  11. The fuzzy control for temperature of decomposition furnace of cement rotating kiln

    水泥回轉窯分解爐溫度的模糊控制
  12. With the increase of the gptms, the decomposition temperature of the rare earth complexes decreased gradually, which also indicated that the existence of the organization results in the decrease of the decomposition temperature of the rare earth complexes in the gels

    由於hy ： h 」配合物在teos水解縮聚形成的祆。凝膠中原位合成程度較小，所以隨著ph的上升，熒光逐漸增強，在ph值達到5對左右時，熒光達到最強，表明a 。
  13. A solid - state shear compounding technology based on pan - milling ( s3c ) has established, by which the graphite with weakly combined structure are exfoliated and then compounded with pp at nanoscale. the obtained pp / graphite nanocomposites have greatly enhanced electrical and thermal conductivity. their structures and properties were characterized by analysis of particle size and distribution, sem, tem, xrd, the electrical conductivity, the thermal conductivity and heat - decomposition temperature etc. by taking advantages of the layered inorganic fillers with a weak interaction between layers ( e. g

    磨盤碾磨剪切力場使pp分子鏈斷裂，相對分子質量減小，石墨的導熱和潤滑性能抑制pp的降解和粉碎，使pp / yep250 （膨脹石墨250倍）復合粉磨盤碾磨固相剪切復合技術及導電導熱pp /石墨納米復合材料的制備與性能體中， pp分子運動活性提高，結晶能力增強，為pp在熔融加工中進一步向己剝離的石墨片層間擴散，形成納米復合結構創造了條件。
  14. Adiabatic decomposition temperature

    絕熱分解溫度
  15. Mdsc and tga results showed that the terpolymer exhibited an extremely high glass transition temperature and decomposition temperature when compared to the copolymer from po and co2

    結果表明這些三元共聚物具有較高的分子量，且玻璃化轉變溫度隨著主鏈上的環己撐碳酸酯含量增加而逐漸升高。
  16. 05. 02 vapor pressure - temperature relationship and initial decomposition temperature of liquids by isoteniscope, method of test for

    用液體蒸汽壓力器測定液體的蒸氣壓力-溫度關系和初始分解溫度的方法
  17. Standard test method for vapor pressure - temperature relationship and initial decomposition temperature of liquids by isoteniscope

    蒸氣壓力計測定液體的蒸氣壓力-溫度關系及起始分解溫度的標準試驗方法
  18. The liquid crystalline field of the polymers could be well kept at room temperature and the initial decomposition temperature of all the polymers was higher than the clearing point

    所有聚合物的熔點都非常低，表明合成的一系列液晶聚合物非常容易進入液晶態，並且液晶場能夠很好地保存到室溫。
  19. The experimental results also showed that there is a correlation between the burning rates of gap fuel - rich propellant and the thermal decomposition temperature of kp and gap

    具體表現在： gap tmo貧氧推進劑的燃速與常壓下tmo催化劑對ap kp gap模擬貧氧推進劑中gap和kp熱分解的催化作用相關。
  20. And we also give the intercalation mechanism of emulsion polymerization, the reaction calories will be benefit to the exploit of montmorillonite. the properties of acr / mmt / pvc composites were characterized. the addition of montmorillonite can improve the strain strength ; enhance the decomposition temperature and vicat soft point, little influence to impact strength

    將聚丙烯酸酯/蒙脫土納米復合物與pvc樹枝共混，考察了蒙脫土對pvc的改性效果，發現呈納米分散的蒙脫土可以明顯的提高pvc的拉伸強度、熱分解溫度和熱變形溫度，對抗沖性能影響不大。
分享友人
分享到 Line

分享到臉書