density wedge 中文意思是什麼
density wedge
解釋
密度光楔-
Value, and the current density and intensity versus the substorm phases. moreover, the characteristics of substorm current wedge are given special attention. it is found that the density and intensity of facs reach their peak during the expansion phase, the onset of the expansion phase is triggered when imf is changed to southward from northward or the southward imf decreases, and the positions of onset are most likely to be at the edge of plasma sheet near the earth
值分佈以及場向電流強度和密度隨亞暴位相的變化，並著重分析了亞暴電流楔的特徵。結果表明，亞暴膨脹相的場向電流強度和密度都達到極大值亞暴的膨脹相是由行星際磁場轉向或南向分量變小觸發的，其起始位置很可能位於近地等離子體片內邊緣。 -
When the density step wedge has been properly exposed, the film is then processed.
當密度階梯光楔被正確曝光后，即把膠片沖洗出來。 -
Firstly, the comparation study between the wedge pressing and the contour forging has shown that the transverse deforming initiated from the surface of the preforms. when the superficies reached the moulding wall, the deforming moved downwards as the high - direction deforming increased, till the moulding chamber was full of stock ; the transverse deforming of the moulding pressing stock initiated from the center of the stock then surned into a drum - type. the distribution of the density and hardness of the high - direction indicated that the wedge pressing acquired a better ability of pressing penetration
首先對比研究了楔形壓制工藝與模壓緻密化工藝，發現楔壓坯料的橫向變形從上表層開始，當上表面與模壁接觸后，隨著高向變形量的增加逐步向下移動，直至坯料充滿模腔;模壓坯料的橫向變形從坯料中間開始，形成鼓形。高向的密度、硬度分佈表明楔壓比模壓具有更好的壓透能力。 -
Secondly, the effect of transverse deforming on the property of the wedge pressing was studied. the results showed that : the wedge pressing stock with the transverse deforming amount of 10 % acquired the best performance. the highest density got the biggest rate of slope while with the amount of 30 % the curve was more some special structure and performance as following : the large porosities was crushed into small or linear ones with the high - direction deformation amount of 20 % ; as the increasing of the high - direction deforming, the particles got a further deforming, the porosities got a further crushing, the small porosities were mergered by the large ones and the former then disappeared ; when the amound reached 60 %, the quantity of the porosities would obviously decrease which made the materials compact, the microstructure more uniform and the density and hardness curves more horizontal, the relative desity could reach 99. 7 %, the tensile strength b of the as - compacted samples reached 408mpa with the yield strength s teached 289mpa and the elongation percentage reached 13. 6 %. in addition, the microstructure of the wedge pressing stock under the pressing temperectureof 450 was uniform, the porosities and the boundries of the grains basically disappeared and the conjunction between particles was great
採用雙向楔形壓制，大尺寸噴射沉積5a06鋁合金楔壓坯的組織和性能變化具有如下特點:當高向變形量為20 %時，大的孔洞變形破碎為小的孔洞，或呈線狀孔;隨著高向變形量的增加，顆粒進一步變形，孔洞進一步破碎，大孔「吞併」小孔，小孔塌陷並逐步消失;當高向變形量達到60 %時，孔洞量大為減少，材料基本緻密，組織趨于均勻，楔壓坯料的密度、硬度變化曲線接近水平線，坯料的相對密度達99 . 7 % ，抗拉強度_ b = 408mpa ，屈服強度_ （ 0 . 2 ） = 289mpa ，延伸率= 13 . 6 % ;對比其它的壓制溫度，在450楔形壓制的坯料組織均勻，孔洞及顆粒邊界基本消失，顆粒之間冶金結合良好。 -
Referring the sensitization monitoring method, the quantitative measurement by the wedge and the anti - dust performance expressed by optics density quantity had been developed. the concept of the indicator of anti - dust was put forward. at the same time, the anti - dust function was used as a index of optoelectronic sensor " s performance evaluation
深入研究了農用光電傳感器的抗塵問題，借鑒感光測定方法，開創性地提出了用標準光楔進行量化測量和用光學密度量化表示光電傳感器抗塵性能的方案，提出了抗塵指數的概念，並在此基礎上提出了將抗塵性能作為開關量光電傳感器的一項性能評價指標。 -
And by using the wedge accumulation model, a formula for calculating the angle of repose of symmetrical dispersed sediment is deduced ; and then combining the calculation formula of dry density, the angle of repose of symmetrical dispersed sediment can be calculated
運用散體沙的楔入堆積模型，推導散體沙的水下休止角計算公式，並結合干容重計算公式，計算散體沙的水下休止角。
分享友人