diameter of outlet 中文意思是什麼
diameter of outlet
解釋
排氣口直徑-
Based on the topographic features and data of sediment particle size of bed load at the fluctuating backwater reach of liujiaxia reservoir, the streamwise variation and variation process of median diameter of bed load during silting and scouring periods of the fluctuating backwater reach are analyzed, and it can be seen that the turning point for the sediment diameter variation from coarse to fine is located at the outlet of shigou gorge of the fluctuating backwater reach
摘要根據劉家峽水庫變動回水區的河段地形特徵和歷年河床質泥沙粒徑級配資料，分析了變動回水區河段淤積和沖刷時，河床質泥沙中值粒徑的沿程變化和歷年河床質泥沙中值粒徑變化過程，並指出粒徑分佈由粗變細的轉折點在變動回水區寺溝峽峽口處。 -
Through developing a 2 - dimensions heat transfer model of buried pipe - in - pipe heat exchanger and simulating the process by computer, the author figures out inter - relations of factors which influence characteristics of buried pipe - in - pipe heat exchanger, such as pipe diameter, pipe length, ratio of pipe diameters, flow rate, inlet water temperature, patterns of water inlet and outlet, and material features made of pipe, and proposes some optimizing indexes of buried pipe - in - pipe heat exchanger. the author studies the " heat - - short circuit " phenomenon as well and gives < wp = 5 > some important results
本文通過建立地下套管式埋管換熱器傳熱過程的二維傳熱模型，並藉助計算機對分析結果進行解析，弄清了影響埋管換熱器性能的管徑、管長、管徑比、通過流量、進水溫度、進出水方式以及管材等參數的作用，並提出了相應的優化指標，對研究界懸而未決的「熱短路」問題也進行了細致分析，得出了有關結論。 -
The dehydration time is square of the droplets diameter so the small diameters of the droplets can cut down the drying time then reduce the height of the drying chamber. to the combined spin - flow pressure spray drying, the diameters of droplets are small and the dehydration rate is higher so keeping the qualities of the dried products we can increase the speed of the inlet wind and reduce the temperature of the outlet wind thus can improve the evaporation intensity of the drying chamber and the average energy utilization of the drying equipment
因霧滴的脫水時間與其直徑的平方成正比，減小液滴直徑有利於縮短乾燥脫水時間，可有效降低乾燥塔的高度；由於旋流式組合壓力噴嘴霧化滴徑的減小，脫水速度明顯加快，在不影響乾燥物料性質的前提下，適當提高進風溫度，同時有效地降低排氣溫度，有利於提高幹燥塔的蒸發強度，也有利於提高幹燥設備的平均能源利用率。 -
Using three - dimensional particle trajectories dispersed droplet diameter at the outlet of screw element during compounding in a co - rotating intermeshing twin - screw extruder was computed
摘要用物料三維流動路徑結合分散模型計算了螺紋元件出口處分散相液滴的直徑，分析了螺桿轉速、擠出機產量和液滴初始直徑對末端分散相液滴直徑的影響。
分享友人