dipping time 中文意思是什麼
dipping time
解釋
蘸塗時間-
Different factors influencing the effect of antibiosis finishing for knitted socks are experimented ; including concentration of finishing agent, dipping temperature, dipping time, baking temperature, baking time and bath ratio
摘要通過實驗確定整理劑濃度、浴比、浸漬溫度、浸漬時間、焙烘溫度和焙烘時間對滌棉針織襪抗菌防臭整理效果的影響。 -
Astrazeneca has been dipping its toes in asian waters for some time
阿斯利康試水亞洲市場已經有一段時間了。 -
The theoretic cycle capacity of limno2 is 286 mah g - 1, which has attracted a great deal of people to research. aim at the impurity of limno2 which was synthesized by the predecessor and the phase change during the electrochemical process, we try several methods, including wet moist chemical method, liquid state method, solide state method and liquid dipping method. at the same time, we study the synthesis of limnc > 2 in defferent atmosphere, for example air, argon and nitrogen
Limno _ 2具有286mah ? g ~ （ - 1 ）的理論容量，這種高容量材料深受廣大研究者的關注，針對前人合成出的還有少量雜相和在電化學循環過程中出現相變四川人學碩l :學位論文的問題，我們嘗試了幾種合成方法:濕化學法、液相法、固相法和溶液浸漬法，並在不同氣氛:空氣、氮氣和氫氣中進行limnoz的合成研究。 -
The oxidizing kinetics equations of different dipping time of dipping two kinds of phosphate saturable solution were determined. the influences of dipping time of dipping two kinds of phosphate saturable solution on antioxygen properties of sic kiln furniture were also studied. the effect of dipping two kinds of phosphate saturable solution were compared. both of their best dipping time were determined
探討浸漬兩種磷酸鹽飽和溶液次數對窯具材料結構和性能的影響，確定浸漬兩種磷酸鹽飽和溶液不同次數的氧化動力學方程，分析其對sic窯具材料抗氧化性的影響，比較兩種磷酸鹽飽和溶液的浸漬效果，並確定各自的最佳浸漬次數。 -
Abstract : in this paper, the preparation of the catalysts for the oxidation of fluorene to fluoreone is studied. the influences of the dipping time, calcining temperature, calcining time and the air quantity during the calcination are discussed
文摘:研究了用工業芴氣相氧化制取芴酮的催化劑製作條件，考察了浸漬時間、煅燒溫度、煅燒時間和煅燒空氣量對催化劑製作的影響 -
The effect of composition of coating solution, dipping time and other technical parameters for preparation of sensors on sensing behaviour has also been described and discussed
討論了溶液組成，浸漬時間等元件制備工藝參數對響應特性的影響。發現電極結構對于元件響應特性有一定影響。 -
X - ray diffraction analysis and mult - peak separation applied software procedure analysis were used to determine the crystal phase and amounts of each sample. the influences of dipping time of dipping two kinds of phosphate saturable solution on the structure and the properties of kiln furniture were studied
探討浸漬兩種磷酸鹽飽和溶液的浸漬機理，並用掃描電鏡的分析結果加以驗證；採用x -射線粉末衍射分析與多峰分離應用軟體程序分析、確定各試樣的晶相，計算各晶相的含量。 -
Acid dipping process which is a must to clean sand dust increases production time and cost. to shorten surfacing production time cost
噴砂處理后的鋁合金部件表面欠缺光潔度，表層微塵粉?需要化學拋光或電解拋光 -
The compositions and the configurations of the composite films were tested by means of ft - ir, xps and afm. the optimal procedure was obtained by studying the influences of the dipping time, and the annealing temperature on the capacitance increase percentage
藉助于ft - ir 、 xps 、 afm等分析手段對復合氧化膜的成分和結構進行了分析，並研究了sol - gel技術的主要工藝參數對鋁陽極氧化膜電性能的影響。 -
The results show that, the capacitance of aluminum foils is increased at the different rated formation voltage, the forming time become so little that the power was mostly saved, but the withstanding voltages of the dipping foils become lower. the dipping time and the annealing temperature are the key factors influencing the capacitance of aluminum foils fabricated by sol - gel technology. 2
結果表明: sol - gel技術在鋁腐蝕箔表面成功制備出了高介電常數的al - ti復合氧化膜;經tio2溶膠處理過的鋁腐蝕箔陽極氧化后，復合氧化膜使不同陽極氧化電壓下的化成箔比容均有不同程度的提高，而且陽極氧化過程變短，節約了電能;但是耐電壓特性變差。 -
( 2 ) two methods including one - step and two - step methods were used to modify the platinum electrode. in the two - step method, the experiment conditions were confirmed, namely after modified by nafion film, the electrode was dipped in saturated solution of co ( salen ) for 24h. the electric current would decrease if the dipping time were too long
2 .用兩科，方法對電極進行co （ salen ） / nafion修飾，即「一步法」和「兩步法」 ，對「兩步法」的實驗條件進行了選擇，即將電極表面先修飾好nafion膜后，再浸泡在co （ sa1en ）飽和溶液中24h即可，時間再長則峰電流反而會減小。 -
Hydrocarbon reserve was also calculated, providing sounding basis of the progressive exploration and development of the oil field via the study, following results was achieved : 1. oil formation of huan xi ling xiqi 14 area was for the first time fully understood through comprehensive three dimensional interpretation method, showing that the structure dipping from north to south and west to east
詳細研究了新齊14井區杜家臺油層構造、沉積、儲層及油藏特徵，並進行了測井二次解釋評價，計算了油氣儲量，為油田增儲上產及滾動勘探開發提供可靠地質依據。
分享友人