direct digital control system 中文意思是什麼
direct digital control system
解釋
直接數字控制系統-
Step - forced dynamic speed drop analysis digital control, dual ring, direct current and reversible speed governing system
數控雙環直流可逆調速系統階躍擾動動態速降分析 -
This paper mainly focuses on the noise limiting by means of the direct sequence spread spectrum ( dsss ) and the analysis of the transmission performance of the plc and some digital modulation technology. the contents of the paper is as follows : 1 ) the technical feasibility is proved after simulating noise limiting principle of dsss by means of systemview, the simulation software ; 2 ) a kind of band pass filter ( bpf ) is realized according to the requirement of filter and the principle of butterworth approximation, which satisfies the index of performance of dsss. 3 ) the low voltage plc system includes the sc1128, the specific modulation / demodulation ic, the bpf filter and other circuit components, furthermore, the control function of system is realized by means of the personal computer and the microcontroller
本課題在對低壓電力線的傳輸特性和數字調制技術進行分析的基礎上，將通信理論中的直接序列擴頻技術（ dsss ）用於解決低壓電力線通信的干擾問題，主要研究內容如下： （ 1 ）用通信模擬軟體systemview對dsss技術的通信和抗干擾原理進行模擬分析，分別對時域和頻域下採用dsss技術前後接收信號的頻譜進行分析，驗證dsss技術在本系統中的可行性； （ 2 ）由dsss技術對濾波系統的要求，根據濾波理論分析了巴特沃思型濾波器的逼近原理並設計了合適的濾波電路； （ 3 ）用調制解調晶元sc1128和自行設計的濾波器加之輔助外圍電路，構造出低壓電力線載波通信系統，並採用atmel公司的單片機設計了接收和發射電路的微控制器； （ 4 ）分別對採取抗干擾措施前後輸入和輸出信號進行對比實驗，並對結果進行分析，驗證了dsss技術對干擾信號的抑制作用。 -
Based on the quick development of computer network, this thesis deals with how to apply network technology to civil and architectural engineering. the finished research contains as follows : the research on reraote - network - monitor - system, the realization of the data collection of ddc ( direct digital controller, multi - loop data circuit monitor ), the communication, the real time control of remote network. moreover, the remote - network - monitor - system is applied in the engineering practice in which monitoring the security of high framed girder and plank
其中包括：研究了遠程網路檢測系統基本結構，實現了下位機（多路數據巡迴檢測儀）現場數據採集、下位機與上位機通信、遠程網路實時控制採集過程等；成功編制了下位機與上位機通信軟體和用於動態更新、存儲數據的數據庫系統；將遠程網路檢測系統應用於工程實例，完成了高層建築框支梁安全性監測、不抽芯板專利技術檢測。 -
Aim at the dtc ' s blemish mentioned above and the direction of dtc technique development, the dissertation put great emphasis on the work as follows, with an eye to exalt dtc system function : ( 1 ) a new speed - flux observer of an induction motor is proposed to enhance the accuracy of flux observing, which is an adaptive closed - loop flux observer and different from the traditions. a new adaptive speed - observation - way is deduced out according to the popov ' s stability theories ; ( 2 ) to improve the performance of dtc at low speed operation, we have to exalt the accuracy of the stator flux estimation and a new way of bp neural network based on extended pidbp algorithm is given to estimate and tune the stator resistance of an induction motor to increase the accuracy of the stator flux estimation ; ( 3 ) digital signal processor is adopted to realize digital control. an device of direct torque control system is designed for experiment using tms320lf2407 chip produced by ti company ; ( 4 ) bring up a distributed direct torque control system based on sercos bus, sercos stand for serial real time communication system agreement which is most in keeping with synchronous with moderate motor control ; ( 5 ) the basic design frame of the hardware and software of the whole control system is given here and some concrete problem in the experiments is described here in detail
針對上面提到的直接轉矩控制的缺陷和未來直接轉矩控制技術發展方向，本論文重點做了以下幾個方面的工作，目的在於提高dtc系統的綜合性能： （ 1 ）提出一種新型的速度磁鏈觀測器，新型的速度磁鏈觀測器採用自適應閉環磁鏈觀測器代替傳統的積分器從而提高磁鏈觀測的精度，並且根據popov超穩定性理論推導出轉速的新型自適應收斂律； （ 2 ）改善系統的低速運行性能，主要從提高低速時對定子磁鏈的估計精度入手，提出了一種提高定子磁鏈觀測精度的新思路? ?利用基於bp網路增廣pidbp學習演算法來實時在線地修正定子電阻參數； （ 3 ）採用數字信號處理器dsp實現系統全數字化硬體控制，結合ti公司生產的tms320lf2407晶元，設計了直接轉矩控制系統的實驗裝置； （ 4 ）提出了基於sercos總線網路化分散式的直接轉矩控制系統， sercos （ serialrealtimecommunicationsystem ）是目前最適合同步和協調控制的串列實時通信協議； （ 5 ）基本勾勒出整個控制系統的硬體和軟體設計基本框架，詳細描述一些實驗中的具體的細節問題。 -
The configuration that uses ieee - 13 94 to control a vxi system is introduced. chapter 2 describes the resource manager application of message - based device 13 94 - vxi controller and the mechanism of register - based device arbitrary waveform generator ( awg ). the key technology of interface circuit and direct digital synthesis in awg module is discussed explicitly
本文先對vxi總線技術進行了概略的介紹，在此基礎上，對一具體的vxi寄存器基任意波形發生器模塊進行展開，介紹了任意波形發生器模塊與vxi機箱背板總線通訊的介面電路部分及波形發生機理的核心部分的直接數字合成技術。 -
The hotel ' s rooms clean and comfortable, with both domestic and international direct dial telephone, digital television, broadband internet access, electronic door locks and independent temperature control system
酒店的客房清潔舒適，配有國內、國際直撥電話、數字電視、免費寬帶上網、電子門鎖及獨立溫控系統。 -
The thesis first probably explains brushless direct current motor ( bldcm ), and discusses the related control methods, explains the background and meaning of back electromotive force ( back - emf ) which is used in the thesis. then the thesis expounds the basic component parts, the basic running principle, the running characteristic and transfer function of the bldcm. and then the thesis detailedly dissertates its research pivot : the simulation of bldcm system in matlab based on the method of back - emf and the control system of digital signal processor ( dsp ) based on the method of back - emf
本文首先對無刷直流電機進行了概述，並對其相關控制方法進行了討論，說明本文所採用反電動勢法的背景和意義;接著論述了無刷直流電機基本組成環節、基本工作原理、運行特性和傳遞函數，然後是詳述本文研究的重點:基於反電動勢法的matlab調速系統的模擬以及基於反電動勢法的dsp控制系統的實現。 -
Hardware design uses high - speed digital signal processor tms320lf2407a as the key control part. software design adopts hexagon stator flux scheme and round stator flux scheme respectively. after the system is set up, the direct torque control method is realized for a 0. 12kw winding asynchronous motor
最後根據以上的討論和實際應用中的情況，分別採用六邊形磁鏈方案和圓形磁鏈方案，以高速數字信號處理器ths320lf2407a作為核心控制部件，在一臺0 . 12kw的繞線式異步電機上實現了異步電機直接轉矩控制。 -
One - wire bus is a new technique based on cdma and std. it has simple structure, low cost, direct control via computer or microprocessor and simple program. the new type of one - wire digital sensor, which is integrated with thermometer, a / d, controller, rom, ram, can communicate with server computer through 1 wire and without any other accessories, moreover, 64 sensors can share one single line which makes system structure concise and easy
新型的單總線數字傳感器集成了溫度檢測、 a d轉換、控制器、 rom 、 ram 、單線雙向數據傳送等功能於一體，只需要1根數據線，無需其他輔助器件即可實現傳感器與主機間的數據通訊，而且多達64個數字傳感器可以共用該數據線，使系統間的連接非常簡潔，適應于低成本的多點測試、集中控制系統。 -
In this paper, it is carried out the controlled system of single - chip microcomputer ( at89c52 ), which is based on ddc ( direct digital control ), to resolve the synchronization of the amount of seeding transplant and velocity, and utilize series voltage regulator to resolve the stability of the voltage
本文採用型號為at89c52單片機（單片微型計算機single - chipmicrocomputer ）的直接數字控制（ directdigitalcontrol ）技術，解決擺秧機行走速度與擺秧量同步性的問題。 -
The power circuit of the system adopts the voltage frequency conversion structure of ac - dc - ac, and is composed of the commutation circuit, filter circuit and intelligence power module ( pm15rsh120 ). control circuit takes the dsp chip tms320lf2407 as core, including the pwm signal occurrence circuit, detect circuit of stator current and direct current voltage of generatrix, drive circuit of intelligence power module, detect circuit of speed, protect circuit of system etc. all of this builds the full digital vector control system of asynchronous motor
該系統的功率電路採用電壓型的交-直-交變壓變頻結構，由整流電路、濾波電路及智能功率模塊ipm （ pm15rsh120 ）逆變電路構成;控制電路以dsp晶元tms320lf2407為核心，加上pwm信號發生電路、定子電流檢測電路、直流母線電壓檢測電路、智能功率模塊驅動電路、速度檢測電路、系統保護電路等，構成了功能齊全的異步電機全數字化矢量控制系統。 -
A single neural cell self - adaptive controller is studied. furthermore, a direct digital control system of srm based on this single neural cell self - adaptive controller is designed by using mcs - 80c196kb microprocessor
本文對單神經元pid自適應控制器進行了模擬，並將此演算法應用於sr電機直接數字控制系統中，以intel公司的mcs - 80196kb為控制器，進行了軟硬體的設計和調試。 -
A new all - digital fuzzy direct torque control servo system of pmsm based on dsp ( tms320lf2407a ) is designed and constructed, in which the traditional space voltage vector selector is replaced by an analytic fuzzy control state selector
摘要提出在pmsm直接轉矩控制系統中，採用解析模糊控制狀態選擇器替代傳統的空間電壓矢量選擇器的新型控制方法，設計完成了基於dsp （ tms320lf2407a ）為核心的全數字模糊直接轉矩控制系統。 -
In this dissertation, the author has accomplished the simulation of the dtc system and analyzed the corresponding results. the software of the digital control system, in which the digital signal processor ( dsp ) is used, has also been designed in the thesis. the direct torque control scheme is studied in the paper, and the simulation models of hexagon flux control system and approximate circle flux control system are presented based on the application of matlab / simulink
本文對異步電機直接轉矩控制變頻調速方法進行了研究，採用mathworks軟體公司為matlab開發的系統模型圖形輸入和模擬工具simulink對直接轉矩控制的六邊形和近似圓形兩種定子磁鏈控制方法進行了模擬，實現了有速度傳感器的直接轉矩控制系統的構建，從理論上證明了這兩種方法的可行性。 -
On the building services side, a direct digital controlled air - conditioning system with plant optimization programme control was installed to maximize operational efficiency
屋宇設備方面，採用了直接數碼控制系統，配合機組最優程序控制，令空調系統達至最高效率。 -
( l ) in order to conquer the complexity of controller, the direct adaptive neural network control is induced into active vibration control system and the digital simulation is made on the two - stage isolation mounting. the error channel is replaced with sgn function in this method. the results indicate the theoretical feasibility of the method
（ 1 ）將直接自適應神經網路控制方法引入雙層隔振振動主動控制系統，該方法將誤差通道納入神經網路用sgn函數替代，不需要預先或在線辨識系統的數學模型，從而降低了控制系統的設計復雜性，在雙層隔振臺架上進行了數字模擬研究，結果表明了該方法的理論可行性。 -
These parameters include bandwidth, carrier frequency, signal duration and signal repeat frequency. according to the parameters, we select the method direct reading the stored digital waveform to realize the waveform generation in the third part, the waveform generator system control including communication control, timing control and address generation is designed
第二部分研究了線性調頻信號參數間的內在聯系，包括信號帶寬、中心頻率、持續時間及重復頻率等，設計了信號參數，並在前人研究的基礎上選擇了波形存儲直讀法作為信號產生方案。 -
A direct digital control ( ddc ) system was adopted, which can grab the dynamic image of fruits in real time, and send the results of image processing to the parallel port of computer, then control several step motors " status at the same time
本研究採用計算機直接數字控制方式，對動態水果圖像進行實時採集，並通過計算機的列印埠輸出圖像處理結果，實現同時對多個執行器的動作狀態進行控制。
分享友人