displacement diagram 中文意思是什麼

displacement diagram 解釋
變位曲線
  • displacement : n 1 轉位，移動；取代，置換；（人的）流離失所。2 撤換，免職。3 【機械工程】（活塞）排氣量；【航海...
  • diagram : n. 圖，圖形，圖解；【數學】作圖。 a diagram of an engine 發動機設計圖。vt. （-gram（m）ed; -gram（m）ing） 用圖表示，圖解。
  1. The radome causes an angular displacement of the tracking aerial polar diagram.

    天線罩使跟蹤天線的極圖產生了角位移。
  2. Computer methods for drawing displacement diagram of statically determinated structure

    靜定結構位移圖的計算機繪制
  3. Method of inverse displacement analysis for hybrid twe pmts is a1so given. an analytical method, which is based on surface analysis, for workspace - analysis of 6 - sps type pmts is proposed in this dissertation. topological diagram of workspace for 6 - sps type pmts is derived, the equations of workspace boundny surfaces for 6 - sps type pmts are also derived based on the kinematic characteristic of the pmts

    提出了一種求解6 - sps型並聯機床主進給機構工作空間的解析方法，該方法以曲面分析為基礎，通過分析得到了6 - sps型並聯機床主進給機構工作空間四川大學博士學位論文的拓撲邏輯結構圖，結合主進給機構的運動特性，得到了主進給機構工作空間邊界曲面的曲面方程。
  4. At the end, the vibration responses are displayed in polar diagram synthetically, in which the displacement, the static offset and the deflection angle of rotor could be shown altogether

    提出用極坐標表徵轉子振動特性的方法，可以更直觀、全面地反映轉子的振動幅度、機動飛行時的靜態偏移以及偏擺角。
  5. This paper introduces the development and present situation of vibration absorb technology in the world ; generally analysis the rubber - bearing ( rb ) and lrb " s operative mechanism, function and the calculation of parameter ; advance the concept of standardization to lrb ; on the basis of generally analyzing the connected factor such as the site category, the diameter of lead bar, the height of bearing, the designing carrying capacity, the span of bridge, the inherent period and the displacement of rb, determine the parameter, the absorbing vibration target, the method and the process of standardization to lrb ; then according to the two - step rule of resisting and defending earthquake, and combining with the response spectrum theory in the seismic vibration of bridge, make a lot of calculation and analysis of vibration absorb design to the real bridge collected and combined by finite element program ; at last, gives the result of standardization through diagram and explains to its usage

    本論文介紹了國內外減震技術的發展和現狀；綜合分析了普通板式橡膠支座和鉛銷橡膠支座的工作機理、性能及參數的計算；提出了鉛銷橡膠支座標準化的概念；在綜合分析場地土、鉛銷直徑、支座高度、設計承載力、橋梁跨徑、固有周期以及支座變位等影響因素的基礎上，確定了鉛銷橡膠支座標準化的參數、減震目標、方法和過程；並根據抗震設防兩階段原則，結合橋梁地震振動理論的反應譜法，運用有限元程序對收集和組合的實橋進行了大量減震設計的計算和分析；最後以圖表的形式給出了鉛銷橡膠支座標準化的結果，並說明了其使用方法。
  6. ( 3 ) reinforced concrete frame columns modeled by using three - dimensional solid element to concrete and three - dimensional bar to reinforcing steel bar, and at the same time consideration the adhesive bond between reinforcing steel bar and concrete, the fem is used. by choosing reasonable element, determining mesh division and load steps, simulation of load - displacement, cracking, yielding and ultimate load, crack development history, and calculating fail crack diagram of reinforcement concrete frame columns under laterally monotonic load are conducted. the analyses are compared with the experimental results

    （ 3 ）混凝土用三維實體單元、鋼筋用空間桿單元對鋼筋混凝土框架柱進行三維建摸，而且同時考慮了鋼筋和混凝土的粘結性能，通過合理的單元選取、網格劃分及荷載步的確定，模擬了單調荷載作用下鋼筋混凝土框架柱的荷載啦移曲線、開裂荷載、屈服荷載及最大荷載、裂縫發展規律、計算破壞裂縫圖，並與相應的試驗結果進行了比較分析。
  7. By means of computing it makes clear that this way is simple, and if you make out the non - polar velocity diagram of planer rigid - body system, you may determine speedily the relations of the imaginary displacement, and moreover it brings about a new way to determine the imaginary displacements of planer rigid - body system

    算例表明，該方法簡單，而且只要作出平面剛體體系的無極速度圖，便可快速地確定該體系的虛位移關系；同時，該方法也為平面剛體體系虛位移關系的確定提供了一條新途徑。
分享友人
分享到 Line

分享到臉書