drawing temperature 中文意思是什麼

drawing temperature 解釋
回火溫度
  • drawing : n 1 延引，牽引；引誘。2 抽簽；拈鬮。3 【機械工程】拔絲；沖壓成形。4 描畫，制圖；圖，圖形；素描；...
  • temperature : n. 1. 溫度，氣溫。2. 體溫。3. 〈口語〉發燒，高燒。
  1. In this thesis, used thermocouple to sense the temperature in the space of the hearth, attributed the thermocouple based on calorifics and scientific arithmetic, acquired data by data acquiring card, processed data according to the demand of setting up temperature model and drawing graphics and then caculated the coordinates of isothermal points and normals of isothermal facets, ascertained the order of connecting points and the model of construct, drawed the isothermal facet of temperature field with opengl at last

    通過數據採集板卡進行數據採集並與計算機介面進行數據處理。然後，將處理后特殊點的溫度數據依據marchingcubes演算法建立數學模型求取等溫面上的點的坐標及各點的法向量等。最後，確定計算的三維坐標點的連接順序和拓撲模型，利用opengl進行等溫面的繪制、消隱和模式變換等工作。
  2. But the temperature difference at the vertical direction in combustion chamber in lead column, that is said by operator, is over 60 ?. ( 2 ) according to the experiences in the practice, the second layer air and the second layer gas had a little effect of support burning, and the third air has little effect for combustion, and the power to drawing exhaust gas can only be adjusted in limited range. the problems, it is said above, restricted more advance of some kinds of technology and economy target in spelter refining in new jersey furnace

    由於鋅精餾爐產量提高，一些問題開始暴露出來： （ 1 ）燃燒室?舶要求溫度差不超過10 ，而從現場反映的情況來看，燃燒室上、中、下部溫度差已超過60 ； （ 2 ）在生產實踐中，發現燃燒室第二層空氣、第二層煤氣作用甚小，第三層空氣失去助燃作用，廢氣出口的抽力可調范圍有限；以上這些問題在客觀上制約了精餾塔在鋅精煉中各項技術經濟指標的進一步提高。
  3. According to differences of construction process, boundary condition, temperature and stress of two schemes extending 3m deep short seam on upstream face in the middle of rcc overflow section and no short seam are calculated, what " s more, in this paper the equivalent line drawing of stable temperature field and unstable temperature field during construction and operation period and the duration curve drawing of typical points " s temperature and stress are plotted, and the results of peak and minimum on temperature in every month and maximum on tensile stress are attained

    根據施工過程和邊界條件，對溢流壩段中間上游面增設3m深短縫和不設短縫兩個方案進行了溫度和應力計算，並繪制出穩定溫度場等值線圖及施工期、運行期非穩定溫度場等值線圖，典型點溫度和應力歷時曲線圖，逐月最高、最低溫度和最大拉應力及相應位置等成果。
  4. In this investigation carbon black - filled electrical conductive composites of poly ( ethylene terephthalate ) / polyethylene were first prepared through the single - screw melt - blended extrusion, then drawing, followed by the quenching and subsequent press molding. the relationships among the influencing factors including composition, hot stretching ratio and compatibilizer, morphology and properties of composites were systematically investigated. positive temperature coefficients effect and crystallization behaviors of composites were preliminarily analyzed

    本文擬採用單螺桿熔融共混擠出?熱拉伸?淬冷的新的成型方法制備炭黑填充的pet pe復合導電材料，熱拉伸的目的是使材料的分散相（ pet相）在加工過程中原位形成纖維，而炭黑基本分散在纖維中或纖維的表面上，使炭黑粒子間間距減小，形成更多的導電通路，從而提高材料的導電性能，同時保持或提高材料的力學性能。
  5. Together with undertaking the power cords designing and researching, it usually takes 15 days to do the development for the new products. the project department has advanced testing equipments mainly including bending testing machine, inserting drawing machine, temperature testing machine, standing pulling machine, internet inspecting machine, chromatic testing machine, static testing machine, salt - spraying machine, burning testing machine, non - toxic inspecting machine

    該部門擁有的試驗檢測儀器包括：搖擺測試機2臺插拔力試驗機1臺高低溫試驗箱1臺立式拉力儀2臺網路測試儀1臺色差儀1臺靜電測試儀1臺鹽霧試驗機1臺燃燒試驗儀1臺低毒檢測儀1臺。
  6. An effective guaranty of stable quality of linen / cotton blended yarn can be achieved by properly choosing of raw material, fully mixing of the fibers in scutching, carding and drawing, taking quality - improving related measures on the equipment, using reasonable technology and process flow, enhancing management and control temperature and humidity in various processes

    通過加大對原料的挑揀力度，在清梳並工序充分混合，設備上採取相應改進措施，選擇合理的工藝及流程，加強運轉管理，控制好各工序溫濕度，能有效保證亞麻棉混紡紗的質量穩定。
  7. It was suitable for melt spinning that temperature was 100 ~ 150, revolving speed was 10 ~ 15r / min and drawing speed was 2 ~ 5m / min

    通過研究發現溫度是影響熔融紡絲的關鍵因素，熔融紡絲較適宜的條件是：溫度為100 150 ，擠出機轉速為10 15r min ，拉伸速率為2 5m / min 。
  8. In order to solve the problems effectively, under the auspices of 863 plan in china, the synthesis diagnosis has been carried by means of measuring and numerical imitating the combustion chamber of refining column, and some conclusions is such as : ( 1 ) through measuring the temperature and combustion in the burning chamber of the refining column, the result shows the temperature difference on the same level is more than that in height direction, and there is a few of co in bottom of burning chamber. ( 2 ) in order to ensure normal work of flue system in lead column in the course of zinc refining, theoretic calculation and measure about the flow resistance of exhaust gas are carried through. the results of study reveal that drawing out force of chimney is inadequate, which is mainly caused by illogicality of flue construction

    在研究過程中，採取了現場實測和數值模擬手段對韶關冶煉廠鋅精餾鉛塔燃燒室及排煙系統進行了綜合診斷，具體結果包括如下： （ 1 ）完成鋅精餾鉛塔燃燒室內溫度測試以及燃燒狀況的測試，結果發現：鉛塔燃燒室內水平方向的煙氣溫度並非均勻，而且其溫差比上下方向的溫差更大，以及鉛塔燃燒室尾部存在co未燃燼問題； （ 2 ）為了保證鉛塔煙氣系統的正常工作，對煙道系統的阻力進行了理論計算及測試分析，結果發現：鋅精餾鉛塔煙氣系統中煙囪抽力不夠，這主要是煙道結構不合理所造成的。
  9. Drawing behaviours reached the best value when the draw rate, draft temperature in bath and the content of baso4 were 200 % ~ 300 %, 40, 60 % ~ 70 %, respectively

    其中對60 % ， 70 %的纖維后加工處理時，其拉伸率為200一300 % ，水浴拉伸溫度為40時，纖維的拉伸性能最好，可得到加工性能比較理想的纖維。
  10. For many experiments, using high pureness mma, controlling polymerization temperature and polymerizing condition under high - pressure nitrogen gas and heat treatment after polymerization, a transparent preform without any bubble and blemishes was prepared. then drawing this preform, gi - pof with diameter 0. 8 - 1. 0mm was obtained. because of the limitation of the experimental conditions and the shortage of the money, it is very regretted that we ca n ' t test the index profile and the loss of the gi - pof accurately

    在系統研究界面凝膠法原理和聚合機理的基礎上，通過多次實驗總結、改進，在制備過程中採用提高精餾效率、控制溫度、加壓聚合、氮氣保護和後期處理等措施，制備出無氣泡及銀紋缺陷、光潔、透明的光纖預制棒，拉絲得到直徑0 . 8 - 1 . 0mm的gi - pof 。
  11. In order to relieve city heat island effect and provide fundamental referential materials for future rational city planning and rebuilding, this paper assorted the underlaying surface of tianjin nankai district according to city planning drawing and airscapes, and analyzed the correlation of city air temperature with city underlaying surface and anthropogenic heat according to air temperature records and city subsurface sorting

    摘要為減輕城市的熱島效應，為今後城市的科學規劃合理改造提供基礎性的借鑒資料，使用城市規劃圖和航空圖片對某市區下墊面分類，並根據實地大氣溫度的監測數據，運用相關分析法和多元回歸分析法，探討了城市氣溫與下墊面和人為排熱等影響因素之間的關系。
  12. The influence of montmorillonite and various drawing temperature on the physical and mechanical properties of pet fiber were investigated. the result showed that the thermal stability of fiber could be improved with drawing temperature increased from 160 to 180

    研究不同拉伸溫度對pet mmt納米復合纖維物理機械性能的影響，結果顯示提高拉伸溫度能改善纖維的熱尺寸穩定性，而對纖維的力學性能、取向等影響不大。
  13. Drawing the following concludes : ( 1 ) for the different metallic small particles with even number or odd number, the heat capacity is varied. the result is different from the bulk metal in essence. at the low temperature, the distribution of the discrete energy levels has important effects on the heat capacity ; at the high temperature, the distribution of the discrete energy levels has little effects because of the involving of mass electrons into the energy distribution

    得到如下結論： （ 1 ）金屬小粒子所含的電子數奇偶性不同，其電子熱容是不同的，這與大塊金屬有本質區別；低溫極限時電子熱容受能級分佈的影響很大；而在高溫時，有大量的電子參與能量配位，比熱遵循大塊金屬的線性規律，能級分佈的影響小時。
  14. Pdlla / ha composite fibers were produced by melt spinning, and the choices of the process parameters such as temperature, revolving speed and drawing speed etc were discussed

    選用熔融紡絲法制備pdlla ha復合纖維，探索了熔融紡絲過程中溫度、擠出機轉速、拉伸速率、加料速度和冷卻速率等一系列工藝參數的選擇及其影響因素。
  15. The a phase can change to b phase by stretching. in the range of low temperature the higher content of b crystalline was achieved during the higher drawing ratio and the higher drawing temperature

    拉伸有利於pvdf纖維的相結晶向相結晶轉變，且拉伸倍數越高相含量越高；較低溫度區域內（ 100 ） ，溫度提高有利於相結晶向相轉變，較高溫度區域內（ 100 ） ，溫度提高對相向相轉變作用不大。
  16. The structure, algorithms, and applications of fuzzy control and ann control system is systematically studied. taking the oil cooler heat transfer characteristics measurement system as the research object, this paper present the hardware design method, and uses visual c on the windows as the tool to implement the fuzzy ann control algorithm. this software also implements temperature real - time control, date collection, analysis and processing, and automatic drawing as well as print

    本文以內燃機機油冷卻器測試系統精密溫度控制為研究對象，設計出了符合高精度溫度控制的機械裝置，在windows平臺下用visualc + +作為編程工具開發出了基於模糊神經網路的精密控溫系統及其應用軟體，實現了精密溫度的實時控制、數據的採集、分析與處理和自動繪圖列印等功能。
  17. Built - in patterns with writing stop, level rotation, zoom, roll, smooth movement, dot drawing, slow drawing, 3d cartoon, strobe and dimmer laser performing effect. housing : high temperature resistant plastic covering, epoxy paint finish

    內置圖案，帶斷筆，水平旋轉，縮放，水平移動，描點， 3d卡通，頻閃，調光等鐳射效果。
  18. Water temperature computation of drawing water line in wanjiazhai water transfer project

    南干線的水體溫度分析
  19. The heat - treatment temperature, the doping concentration of ag ( ag / si ) and drawing speed of the substrates can regulate the size, amount and distribution of silver nanaparticles in the matrix, and then influence the optical absorption of the samples

    結果表明，復合膜的處理溫度、銀的摻雜濃度和薄膜制備時的提拉速度都可使樣品的銀粒子的大小、數量和分佈產生變化，從而影響樣品的光吸收性能。
  20. Drawing on a multifunctional internal friction instrument and dma, we tested the damping capacity of all the heat treated samples completely, and then got the damping - frequency spectrum, temperature spectrum and strain amplitude spectrum

    然後，在多功能內耗儀和dma上對各熱處理態試樣的阻尼性能進行了全面測試，獲得了內耗頻率譜、溫度譜和振幅效應譜。
分享友人
分享到 Line

分享到臉書