elastic element 中文意思是什麼
elastic element
解釋
彈性單元-
Fist of all, on the basis of the research of agone boffins, this author investigates the interaction mechanism of bolts and rock, and introduces the elastic ? lastic analytical resolution which is consist of the liner structure, the equivalent reinforced wall rock and the original wall rock in the simple loading from the equivalent well - proportioned view ; this solution is very important meaning for the engineering design. on the basis of coulomb friction model, the author introduces the finite element equation of the contact problem in order to provide the academic foundation for the application of msc. marc. finally, combining the engineering practice of the non - linear analysis of shield tunnel through yellow river of the south - north water transfer and using the model of friction, the author researched the evolution law of stress and displacement field in the structure of grouted rock bolts, and analyzed the effect to the stress and deformation of surrounding rock mass due to anchor supports
首先，在前人研究成果的基礎上，對錨桿與圍巖的相互作用機理進行研究，利用全長錨固錨桿的中性點理論，從等效均化的角度來考慮錨桿對圍巖的加固作用，並推導了在簡單荷載作用下，含有襯砌、等效加固后的圍巖、原始圍巖三者的彈塑性解析解，對工程設計有著重要的參考意義；在數值模擬方面，以考慮錨固圍巖滿足規則化庫侖摩擦模型為基礎，利用虛功原理推導了接觸問題的有限元方程的計算格式，為開發運用大型商用有限元軟體msc . marc提供了理論根據，也形成了本文的理論基礎：最後，論文以南水北調東線穿黃隧洞穩定性分析項目為工程實例，利用本文所述的接觸問題的摩擦模型理論，對錨桿支護結構的應力場、位移場的變化規律進行了研究，分析了加錨支護對隧洞圍巖應力、變形的影響。 -
This paper simply introduces the device of on - line monitoring for the thrust of the rotating maching, then discu ed the finite dement analyses on the on - line monitoring elastic dement for measuring thrust in detail, in order to develop the performance of the se or and the device, we calculated the distribution of the stre 、 strain 、 axial di lacement in the elastic element using the finite element method when the axial forces f = 3 104n, the result is very satisfied
簡單介紹大型旋轉機組軸向力在線監控裝置，然後詳細介紹軸向力測力彈性元件的有限元分析，為了提高所研製的測力傳感器的性能，採用有限元方法計算了彈性元件在軸向力f = 3 104n時的應變、應力、靈敏度及軸位移等的分佈情況，分析結果表明：所設計的測力傳感器完全符合廠方的要求及儀表性能指標。 -
First, the theory of fretting wear and studies on fretting fatigue were introduced and the parametric method was used in the process of creating the model of dovetail joints in ug software. the elastic contact problem is analyzed in finite element method ( fem ) and is used to the parameters " distribution and contact stress of the joint are obtained on the base of ansys code. with the effect factor of load frequency, the prediction method of fretting fatigue life of dovetail joint under low and high / low cycle complex load is proposed
本文介紹了微動損傷的機理和微動疲勞壽命的研究方法；利用ug軟體對燕尾榫聯接結構創建了參數化實體模型；基於ansys軟體平臺求解彈性接觸問題，獲得了榫聯接結構接觸應力及接觸狀態量的分佈；在已有微動疲勞壽命預測模型的基礎上，引入載荷頻率影響因子，對低周、高低周復合載荷作用下的燕尾榫聯接結構進行了微動疲勞壽命的預測，與試驗結果對比表明採用本文提出的方法預測榫聯接結構的微動疲勞壽命是有效的。 -
Main ingredients : alga moisture essence, halobios nourish element, avocado, elastic polymer, nutrient and etc
主要成分：海藻保濕精華、海洋生物滋潤素、鱷梨、彈性聚合體、營養元素等。 -
In the last, silo structures or its base is simplified as suspensory beam, witch ca n ' t correspond with project practice o considering the interaction among bulk solid, structure and its foundation, a semi - analytic element method static and dynamic analysis on silo structures on elastic foundations is presented in this paper
本文以某大型筒倉結構為例，考慮到散體、結構、地基的相互作用與影響，考慮地基與基礎及結構的耦合問題，採用半解析半數值的方法對彈性地基上的筒倉結構進行了靜、動力的分析計算。 -
Secondly, based on the syntony frequency and the elasticity mechanics and other correlative professional knowledge, establishes a suit of fsm vibration module system, selects the structure, material and the process and treatment technique of the elastic element in the elastic system of the mirror, analyzes a lot of factors which affect the structure of the rapid controlling reflector and provides the derivation formula
以諧振頻率為出發點，利用彈性力學等相關專業知識，建立一套fsm的振動模塊系統；確立了反射鏡彈性系統中彈性元件的結構、材料的選擇，及加工，熱處理。分析了影響快速控制反射鏡結構的諸多因素，給出其相關推導公式，最後應用solidedge和cosmos軟體對該結構進行了計算機模擬。 -
Besides, this paper adopts the random finite element method, uses geometric and physical mechanical parameters that are relevant to lining weight of surrounding rock, coefficient of lateral pressure, height or buried depth of vertical loading, elastic resistance coefficients of surrounding rock, elastic modulus of support structure, unit weight of concrete, thickness of the structure as well as torsional strength and compression strength of concrete and etc., as random variables, applies the monte - carlo method to sampling by computer, preliminarily evaluates the reliability of bearing capacity and stability of molded concrete lining of the xuefeng mountain tunnel, and obtains the related displacement of the lining, mean value and variance of internal force, and computed the reliability index of lining structures
此外，本文採用隨機有限元方法，將圍巖容重、側壓力系數、垂直荷載高度或埋深、圍巖的彈性抗力系數、支護結構的彈性模量、混凝土容重、結構的厚度以及混凝土的抗扭與抗壓強度等與襯砌結構有關的幾何與物理力學參數作為隨機變量，應用蒙特卡洛理論進行計算機隨機取樣，對雪峰山隧道模注混凝土襯砌的承載力與穩定性的可靠度進行了初步評估，得出了襯砌的相關位移與內力的均值和方差，並計算出了相應的襯砌結構可靠指標。 -
The elastic foundation model is considered as two - parameter elastic foundation model and its effect to moderate - thick plates are taken into account by a set of governing differential equations. united with hu hai - chang ’ s function, least squares collocation weighted residual method which uses b - spline function as trial function is put forward for solving the bending problems. compare with the results of finite element method of lines, spline finite strip method, accurate solution of series etc. it is proved that the method in this article has adequate accuracy and practical feasibility
本文採用瑞斯納中厚板理論求解彈性地基板，建立雙參數地基與中厚板相互作用的控制微分方程，結合胡海昌的解耦函數，運用雙五次b樣條函數作為試函數的離散型最小二乘加權殘值法分析了雙參數地基上的中厚板的彎曲問題，並將結果與有限元線法、有限條法、級數精確解等進行比較，證明本文方法具有足夠的精確性與實際的可行性。 -
In this article, according to heat conduction theory, elastic creep theory and finite element theory, the temperature field and creep stress field in the arch dam during construction and operation are simulated and analyzed by means of three dimensional finite element relocating mesh method, and the distribution law of the temperature field and creep stress field in the arch dam during construction and operation are systematically studied, and according to the construction process of concrete arch dam, the effect of lamination placement, construction interval, elastic modulus change, thermal insulation change, surrounding temperature change, concrete creep and autogenous volume change on thermal stress in the arch dam are also considered
論文根據熱傳導理論、彈性徐變理論及有限元理論，用三維有限元浮動網格法對拱壩施工期和運行期溫度場、徐變應力場進行了全過程模擬分析，較為系統的研究了混凝土拱壩施工期和運行期溫度場、徐變應力場的分佈規律，在分析中按照混凝土拱壩施工過程，考慮了混凝土分層澆築、施工間隙時間、彈模變化、絕熱溫升過程、環境溫度的變化、混凝土徐變、自生體積變形等因素對壩體溫度應力的影響。 -
Another topic of this article is to try to find a proper overlay design method. by using elastic layer system ( els ), finite element method ( fem ), genetic arithmetic ( ga ) back calculation and efficacious thickness method, the paper puts forward four design methods. the results say that the position where the max stress appears is not the only one but varies with the thickness of overlay
根據陜西省高速公路瀝青路面病害以及使用性能的實際情況，提出了代表彎沉值的計算方法以及下臥層模量的反演方法，在此基礎上利用彈性層狀體系理論、有限單元理論、遺傳演算法以及有效厚度法等理論對加鋪層厚度設計方法進行了研究。 -
Finite element analysis of the elastic plasticity of a naval boiler superheater expanded - joint
礦用圓環鏈間接觸應力場的三維有限元分析 -
Solving the wire loop profile for which nonlinearity mainly caused by plastic - elastic forming is a challenging work, a finite element model has been proposed to simulate the wire loop profiling, in which beam23 has been selected as calculating unit, and the trajectory of capillary is divided into many displacement loads and applied on the wire step by step
摘要針對引線成形過程中的材料非線性和幾何非線性問題，選用塑性變形梁beam23單元建立有限元模型，通過時引線分階段分步施加位移載荷模擬鍵合頭的運動軌跡，求解得到相應的引線輪廓形狀。 -
This paper focuses on the research of the stress mechanism of the ribbed shell structure in statics, dynamics and under the explosive load on the basis of the engineering practice of cave depot of single aircraft. in this paper, according to the classical shell theories, the basic differential equilibrium of the ribbed shell structure and the finite element analysis of 3d rippled plate are established, in which the function of annular ribs reinforcement bars and 3d ripped steel plates are distributed in the range of the steel, and the functions along the longitude direction of tension, bending, and torsion are neglected ; applied with dynamic analytical theory, the dynamic model of ribbed shell structure and the analytical theory model of elastic - plastic are set up ; the triangle series method is used to solve the displacement and stress under the distributed load and the concentrated load of the ribbed shell structure
本文以軍用機場地面單機掩蔽庫工程建設為工程背景，首次對內襯三維波紋鋼板混凝土拱型復合結構的受力機理進行了靜力、動力和爆炸荷載的分析研究。根據將橫肋、鋼筋及三維波紋鋼板的作用均勻分佈在殼體范圍內的情況，忽略橫肋、鋼筋及三維波紋鋼板沿殼體母線方向的抗拉、抗彎及其抗扭作用，首次推導出了內襯三維波紋鋼板混凝土殼體的微分平衡方程，建立了有限元計算模型，並採用三角函數法，求解了三維波紋鋼板混凝土拱型復合結構在分佈荷載和集中荷載作用下的位移響應和應力響應，並與普通殼體進行了比較。 -
Based on the relationship between developed scale of urban road and some social variables, we draw a cobo - douglas production function which involves the devotion element of urban road by econometrics method, and by which we can mensurate the elastic coefficient between urban road scale and gdp
本文在研究我國城市道路發展規模與相關社會指標之間相關關系的基礎上，通過運用計量經濟學的方法，建立了包含城市道路設施投入要素的柯布-道格拉斯生產函數，從而測定了城市道路設施投入與城市國內生產總值產出之間的彈性關系。 -
Finite element method could not only obtain all the same stress of interference fit joint under ideal model as that obtained with elastic mechanics method, but also could analyze the contacting edge effect - edge stress concentration caused by con - tact, which could not be solved by elastic mechanics
有限元方法不僅可以獲得與彈性力學完全一致的理想模型下過盈聯接的應力等，還能夠分析彈性力學所不能求解的接觸邊緣效應?由接觸引起的邊緣應力集中。 -
In this paper, the author combines the theory analysis with the experiment research method, and discusses the seismic behaviours, 3d elaborate finite element analysis and simplified model analysis of a kind of multi - function tall building - " sub - shearwall supported by frame ", which is applied widely today. the main contents are as follows : in order to observe the failure process and the earthquake response of the complex structure, and to analysis the seismic behaviour of the structural system and structural members, a 1 / 20 cement mortor model of a complex tall - building which is about to be built was producted and the shaking table test of this model under 26 sorts of earthquake loads was made. using sap2000 finite element analysis program, a 3d analysis model was built in computer, and the elastic time - history analysis of the model was done
本文採用理論分析和試驗研究相結合的方法，研究了目前應用較多的綜合性大廈? ?框支分區剪力墻高層商住樓的抗震性能及空間精細分析和簡化分析方法，主要內容為以下幾方面：對一擬建的復雜高層建築結構，採用1 20比例的空間整體模型，進行了26種工況下的模擬地震振動臺試驗，觀察了結構的破壞過程和地震反應，分析了結構及構件的抗震性能；建立了結構的精細空間模型，利用sap2000n大型有限元分析程序對結構進行了彈性時程分析；通過有限元分析與試驗結果的對比，對結構的抗震性能和抗震能力做出綜合評價，認為該結構由於轉換層上部去掉部分樓板，既可滿足建築設計的通風、採光等要求，又可達到協調結構轉換層上、下樓層抗側剛度的效果，是一種較理想的有多道抗震防線的結構型式。 -
Rapidly active skin cells, promote the circulation of the blood, remove fatigue of the skin, help the penetrate and the obsorb of the nourish element, whiten, moisturize and firm the eye skin, recovery the elastic of the skin, release the black eye circle
功效：能迅速活化肌膚細胞，促進血液循環，消除肌膚疲勞，幫助營養成份滲透，吸收，美白滋潤及收緊眼部皮膚，恢復肌膚彈性，白皙細膩，改善眼周的血液循環，減淡黑眼圈，令雙眼時刻保持健康神采，展現柔滑明眸。 -
Gauges - pressure indicating dial type - elastic element
量規.壓力顯示刻度表型.彈性元件 -
The optimum is obtained after computing and the optimization result indicates that the method is efficient to optimize the elastic element structure. so it could be applied extensively in the engineering of the sensor element optimization design
優化結果表明該方法對傳感器的彈性元件結構起到很好的優化效果，該方法可廣泛應用於傳感器彈性元件的優化設計工程。 -
The paper introduces the method to optimize the elastic element structure of sensor and how to make the elastic element structure optimization come true by using the ansys soft. author takes the structure optimization of one electrical resistance strain gauge extensometer as an example. and establishes the mechanics model, optimization parameter model, optimization mathematics model for the elastic element of the electrical resistance strain gauge extensometer, at the same time, discusses the design space, programs analysis file and optimization control file by using the ansys parameter design language
論文提出用ansys軟體對傳感器的彈性元件結構進行優化的方法，研究了如何用ansys軟體實現彈性元件的結構優化，以應變計式引伸計彈性元件的結構優化為例，建立了應變計式引伸計彈性元件的力學模型、優化參數模型，優化數學模型和對設計空間的探討，用ansys的參數化設計語言編制了分析文件和優化控制文件，經計算獲得最優結果。
分享友人