electrostatic process 中文意思是什麼

electrostatic process 解釋
靜電處理技術
  • electrostatic : adj. 靜電的，靜電學的。adv. -cally
  • process : n 1 進行，經過；過程，歷程；作用。 2 處置，方法，步驟；加工處理，工藝程序，工序；製作法。3 【攝影...
  1. This paper describing for acid fog how to do harm 2030 cm01 acidwashing technological process sector, principle of electrostatic removing acid fog, removing course, spot application, technological process, and so on, then demonstrating acid fog density before removing and after in the main spot by chart

    詳盡敘述了酸霧對該廠2030cm01酸洗工藝段的危害及靜電凈化酸霧的原理、凈化過程、現場使用、工藝流程等，並將治理前後主要部位的酸霧濃度列表說明。
  2. The damage of acid mist to the 2030cm01 acid washing line, the principle, the purifying process, the design characteristic and the live using of electrostatic demisting precipitator are introduced

    本文概述了酸霧對該廠2030cm01酸洗工藝段的危害，並對靜電除霧器的工作原理、凈化過程、設計特點和現場使用等方面作出了系統論述。
  3. First, a simple discussion for the mechanism about electrostatic atomization of the liquids has been given ; then the paper theoretically analyzed waving course, liquid drop producing course, and the liquid drop diffusing course in electrostatics atomization process., gave an analysis about the methods about carrying charges to the liquid drop, and analyzed that liquid with high electrical conductivity can be carried charges and atomized by electric field, while the isolated liquid with low electrical conductivity can be charged fully with the soakage electrode and inducing charge methods. at last the paper designed and configured the experimental equipment, conducted the atomization experiment to the three liquid medium - kerosene, emulsifier and alcohol under the same environment, handled the experimental results, then summarized the relationship between liquid electrostatic atomization effect and liquid surface tension, electronic conductivity and viscosity, along with the influence of voltage to electrostatic atomization and so on, found out the liquid atomization rule in high voltage electrostatic field

    首先，對液體介質的靜電霧化機理作了初步的探討，理論上分析了液體霧化過程中射流區、波紋區、霧滴區和霧滴擴散區;然後對液體荷電方法進行了研究分析，對于高電導率的液體，場致荷電和接觸荷電可以使其霧化，而對于電導率較低的絕緣液體，需用浸潤電極荷電和感應荷電方法使其充分帶電;最後，根據前面的研究分析，設計和組裝試驗裝置，在同一環境下對煤油、乳化劑、酒精三種不同液體介質進行高壓靜電霧化試驗，並對試驗結果進行分析處理，總結出液體靜電霧化與液體表面張力、電導率和粘度的關系及電壓對液體靜電霧化的影響等，得出高壓靜電場中液體霧化的一般規律。
  4. Test chart for electrostatic copying process

    靜電圖像測試版
  5. In order to observe process and study the rule of producing and collecting dust, and to study the performance of high - voltage electrostatic dust - collecting system, a set of analog device is designed based on on - site measure for workshop of unloading coal of qing huangdao port

    對秦皇島煤碼頭翻車機房進行實地測量，設計製造了試驗模擬裝置。觀察翻卸作業起塵與收塵的物理過程，描繪起塵量與收塵量之間的變化規律。檢驗了高壓靜電除塵器的工作性能。
  6. Electrostatic precipitation is the leading and most versatile method for high-efficiency collection of dusts, fumes, and mists from industrial furnace and process gases.

    電收塵是回收工業爐及其生產過程氣體中的粉塵，微塵和煙霧的最主要和最通用的高效率收塵方法。
  7. Environment protect requirements of copying machines - power - saving requirements of electrostatic process copier

    復印機械環境保護要求靜電復印機節能要求
  8. Environment protect requirements of copying mchines environment protect requirements of electrostatic process copier

    復印機械環境保護要求靜電復印機環境保護要求
  9. The surface rubbing technique has been commonly used for fabricating liquid crystal display panels by lcd industry. however, the rubbing process may cause electrostatic charge, dust or scratches that tend to destroy the display quality

    然而在摩擦過程中會引起靜電、塵埃造成成品率下降，最嚴重的是摩擦產生的溝痕使微顯示器件的顯示質量降低。
  10. Aimed at some problems such as short spraying distance, electricity - leaking and reverse ionization among electrostatic nozzles existing in the country, a induction charging and pneumatic energy electrostatic nozzle was designed. the basic designing theories, structure and working process of this nozzles were theoretically specified in the paper. and then the atomization quality and charge performances of this nozzle and its affecting factors were studied by carrying out performance experiment and statistic analysis. result of the studies indicate : ( 1 ) some progress were made in solving the problems list above ; ( 2 ) from this nozzle, droplet were minute and uniform, and higher charge - mass ratio can be obtained under lower electrostatic voltage, thus the atomization quality and charge performance of this nozzle were both better ; ( 3 ) within the experiment extend, air pressure at 0. 2mpa, electrostatic voltage at 2400v were the most suitable parameters for the nozzle ; ( 4 ) the regression equations for describing droplet size, intensity of spray current and charge - mass ratio of this nozzle obtained from the experiment data had higher forecast precision ; ( 5 ) cross - effect of all factors were not significant, the atomization quality and charge performance were relative dependency affected by the factors

    諸試驗因素中，充電電壓和噴孔直徑對霧滴荷質比均有極顯著的影響；氣體壓力和液體流量對霧滴荷質比的影響均不顯著；影響霧滴荷質比的主要因素依次為充電電壓和噴孔直徑; （ 8 ）在300v 、 600v 、 1200y 、 1800y 、 2400v 、 3000v六種充電電壓t ，霧滴荷質比先隨充電電壓的增加而增大， 2400v后荷質比減小，推測:對于所研製的噴頭可能存在一個最佳充電電壓; （ 9 ）由充電電壓和噴孔直徑的不同搭配所得霧滴荷質比不同這一結果，可看出，較大充電電壓需配備較大噴孔直徑以增強霧滴荷電效果; （ 10 ） td3 . 6和td3 . 4兩噴頭的霧滴荷質比曲線趨于重合，說明噴孔直徑大於滬3
  11. This charged fiber can be directed or accelerated by electrical forces and then collected in mats or other useful geometrical forms. the diameters of electrospun fibers are in the range of tens of nanometers to several micrometers. in this paper, polyacrylonitrile ( pan ) nanofibers are made by electrospinning pan / dimethylformamide ( dmf ) and pan / dimethylacetamide ( dmac ) with adjusting the main process parameters including electrostatic voltage ( 20 ~ 50kv ), sprinkler aperture ( 0. 5 ~ 0. 8mm ), collection distance ( 15 ~ 25cm ), solution concentration ( 6 wt % - 14 wt % )

    本文主要對聚丙烯腈（ pan ）二甲基甲酰胺（ dmf ） 、 pan二甲基已酰胺（ dmac ）體系進行電紡絲，調節靜電壓（ 20 50kv ） 、噴頭孔徑（ 0 . 5 0 . 8mm ） 、接收距離（ 15 25cm ） 、溶液濃度（ 6wt 14wt ）等過程參數，制得pan納米纖維，纖維平均直徑在200 1000nm ；詳細分析了過程參數對纖維細度、形態等的影響，認為高聚物溶液濃度及靜電壓對纖維細度有決定性影響，其它過程參數如接收距離、噴射孔徑、紡絲溶液溫度、溶液電導率等的調整應以這兩參數為基礎進行。
  12. According to the observations of experiments and the knowledge of electrostatic spray, the process of electrospinning polymer fibers is analyzed

    結合試驗觀測及靜電噴霧技術等知識，對電紡絲形成纖維的過程進行分析。
  13. Safety code for painting - safety for electrostatic powder spraying process

    塗裝作業安全規程粉末靜電噴塗工藝安全
  14. Ink jet printing : a non - contact printing process that combines the use of electrostatic, electronic and computer technology

    噴墨印刷:綜合靜電、電子和電腦科技的一種無接觸印刷。
  15. In fundamental theory, adaptive optics, electrostatic actuation, flexure beam theory and squeeze film damping are researched ; in fabrication, bulk micro fabrication process and surface micro fabrication process are researched and compared, then the structure parameters and layout of a 8 x 8 micromirror array are designed using summit foundry ; in analysis, analytical and numerical method are used to perform static analysis, modal analysis, transient analysis, frequency analysis and to characterize the farfield performance of this 8x8 micromirror array. finally, in order to realize large scale micromirror array with lower snap down voltage, advices are given for further research

    在基本理論方面，通過對自適應光學，靜電力驅動，彈性梁理論和擠壓薄膜阻尼的研究，確定了微變形鏡的配置方案；在加工方面對體加工工藝， mumps工藝和summit工藝進行了研究與比較，並選用殘余應力小，表面質量好的summit工藝對8 8的微變形鏡陣列原型進行了結構設計與版圖設計；在分析方面主要對微變形鏡單元的靜態特性，模態特性，瞬態響應，頻率響應和8 8規模的微變形鏡陣列的遠場光學模型進行了研究，確定了微變形鏡的性能參數。
  16. And many potential factors may give rise to electrostatic ignition or electrostatic explosion in the process of loading, unloading or shipping oil cargoes or during the course of washing tanks

    油輪靜電，對油輪的安全營運是極大的潛在危險因素。在油品的裝卸，運輸及油輪的洗船過程中。
  17. The paper introduces the technological processes of electrostatic powder spraying on large - sized workpiece and some issues that should be paid attention during spraying process

    摘要介紹了大型工件靜電噴粉的工藝流程，以及在實施過程中，應注意的若干問題。
  18. Furthermore, lots of control lines implies that the systems is more susceptible to disturbances by electromagnetic interference ( emi ) and electrostatic discharge ( esd ). in this paper we introduce the design of multi - synchronization monitor by i2c bus which improve monitor performance. this paper discusses how to use i c bus automatically adjust in manufacturing process of monitor

    採用總線技術可使顯示器的調整實現自動化，提高了整機的性能和勞動生產率，節省了成本。採用總線技術可使顯示器的幾乎所有功能都可通過集成ic實現，提高了系統的集成度，減少了外圍元件，利於pcb設計和抗emi 、 esd的干擾設計，提高了整機的穩定性。
分享友人
分享到 Line

分享到臉書