end sleeve 中文意思是什麼

end sleeve 解釋
終端套管
  • end : n 1 端，尖，末端，終點。2 邊緣；極點，極限。3 結局，結果。4 目的。5 最後，死。6 【紡織；印染】經...
  • sleeve : n. 1. 袖子，袖套。2. 【機械工程】套筒，套管，套。3. 唱片套。4. 【氣象學】風（向）袋。vt. 給…裝袖子，給…裝套筒。adj. -less
  1. The main products include high - strength fasteners of 8. 8 and 12. 9 grade and stainless steel fasteners, like hex socket, set screw, hex socket countersunk screw, half - round head hex socket screw, torx head hilt, umbrella - type hilt, bsp line plug throat taps, straight pin, taper sleeve screw, connecting screw, spanner, flying ring, double end screw, hex nut, washer and so on

    本公司主要經營8 . 8 、 12 . 9級高強度螺絲及不銹鋼緊固件，內六角、平杯、圓杯、機米、梅花頭刀把、傘形刀把、 bsp喉塞、塞打、圓柱銷、錐套螺絲、連接件專用螺絲、扳手、吊環、雙頭牙、外六角?螺母?墊圈等。
  2. Triple stitching on front, end lock stitch on armhole must be place on the hidden part of the sleeve seam, as noted it is place on front.

    三針在前面，衣袖的收針必須在隱藏在袖口縫中，請注意它的位置在前面。
  3. Position the fuser film sleeve into heater, and the end of the film with ground ring should be in good contact with the conductive rubber gear of pressure roller or the conductive brush after installation

    請在安裝新定影膜前，在塑料架與定影膜接觸的部位均勻塗上硅脂，盡量在有棱的地方多塗點，以保證定影膜與塑料架的充分潤滑。
  4. Bolted, sleeve - type couplings for plain - end pipe

    平頭管用栓接套筒型聯接器
  5. The distribution of the gas - flow speed is measured at a position 1cm away from the outlet ( the end with larger air - gap ). it is illustrated that the gas - flow speed keeps increasing from the out surface of the inner sleeve to the inner surface of the outer sleeve, and then it decreases gradually

    測量了楔形氣隙流體出口（大間隙埠）外1厘米處空氣流速大小的分佈，發現空氣流速自轉子（內筒）壁面處開始逐步增大，至定子（外筒）壁面處達到最大值，隨后開始減小。
  6. Resembling a leg of mutton in shape ; tapering sharply from one large end to a point or smaller end, as a sleeve or sail

    羊腿形的，一頭寬一頭窄的在形狀上與羊腿相似的；由粗大的一端向另一點或較小的一端突然變細的，如衣袖或船帆
  7. It mainly manufactures automobile fittings, fork fittings, diesel engine fittings and high strength bolts and nuts etc and relevant products chain fittings ( bolt roller sleeve plate chain end joint etc. )

    主要生產汽車配件、叉車配件、柴油機配件及高強度螺栓、螺帽等零部件及相關產品、鏈條配件（銷鈾、滾子、套筒、板式鏈端接頭等） 。
  8. Tubular end - sleeves with plastic sleeve

    帶塑料套的管頭
  9. The reduced pressure detector assembly shall consist of two independent torsion spring check modules, a differential pressure relief valve located between and below the two modules, two drip tight shutoff valves, and required torsion spring check modules and relief valve shall be contained within a sleeve accessible single housing constructed from 304 ( sch 40 ) stainless steel pipe with groove end connections

    這種減壓檢測器總成應該包括兩個獨立扭力彈簧止回閥模塊，一個位於兩個模塊之間的下方的差壓安全閥，兩個防滴漏關閉閥，並且要求扭力彈簧止回模塊和安全閥應該放置在一個套筒內，要易於接近帶溝槽連接的304 （目錄40 ）不銹鋼管的單個外殼。
  10. Tubular end - sleeves without plastic sleeve

    無塑料套的管子端套
分享友人
分享到 Line

分享到臉書