equation of line 中文意思是什麼
equation of line
解釋
直線方程式-
The relation of radius of curvature and error as well as formulas of increasing parameters on condition of constant error are diverted. the equation of the line on the center of approximate circular arc is obtained ， and it can avoids the trouble that numerical solution owns possibility of no convergence and simplifies node calculation of non - circular curve
導出了曲率半徑與逼近誤差之間的關系和等誤差條件下的參數遞推公式，建立了通過逼近圓弧圓心的直線方程和圓心坐標計算公式.按這種方法用圓弧逼近平面參數曲線，不需要求解非線性方程組，避免了計算可能不收斂的麻煩，簡化了非圓曲線的節點計算過程 -
First calculation method : doing horizontal projection drawing on drawing piece, k value is introduced by area equation of projection drawing, k value is obtained by area equation, along outline of projection drawing to add k value, that is, outline shape of blank drawing, principle area - equal and shape similar are used. second calculation method : along outline of drawing piece horizontal projection drawing, to do normal line of penetration line for wantonly point of this point, to obtain high of drawing piece on this point normal line, point and point is to form outline shape of blank
計算方法之一為k值法：作拉深件水平投影圖，在該投影圖面積方程中引入k值，利用面積相等原理解方程，求得k值，沿水平投影外沿加上k值，即為毛坯圖的外廓形狀。計算方法之二為拉深線法：沿拉深件水平投影圖外廓，在任意點作該點切線的法線，在該法線上以該點拉深件的高度為量，在法線上取截點。 -
On the condition of “ many - head ” and “ small drive ratio ” ， the plane double enveloping hourglass worm can not settle the problem of undercutting and sharpening simultaneously. it has devoted to a new type hourglass worm _ sphere double enveloping hourglass worm. the coordinate system is established according to the frock. the meshing equation and the tooth equation of worm and gear have been developed and the distribution of contact line on gear tooth is analyzed. to evaluate the meshing quality ， four meshing quality indexes and five original parameters are put forward. through mass programming computing ， the relations between meshing quality and original parameters are derived and depicted by graphs
考慮到平面二次包絡環面蝸桿傳動在多頭小傳動比條件下根切與齒頂變尖的矛盾很難同時解決且嚙合性能較差，介紹了一種新型環面蝸桿傳動? ?球面二次包絡環面蝸桿傳動.在研究過程中，根據工裝建立了坐標系，根據一二包過程的運動關系推得了嚙合方程和蝸桿與蝸輪的齒面方程，分析了蝸輪齒面上的接觸線分佈.為了評價嚙合性能，提出了4項性能指標和5項原始參數，通過大量編程計算得到了嚙合性能指標與原始參數之間的關系，並以圖表直觀的表示 -
Creative points and all tasks having be finished are briefly shown below : according to the classical space meshing theory, we have strictly deduced a series of formulae such as the equation of contacting line of worm, the equation of the second limiting curve of worm gear, and the equation of working surface and non - working surface, etc. and we have deeply studied the algorism of the actual contacting lines of worm gear drive
本文的主要創新點和成果如下：基於經典共軛嚙合理論，對平面二包蝸桿副的運動關系進行了嚴密分析，獲得了蝸桿副齒面方程、蝸桿齒面一界曲線方程、蝸輪齒面二界曲線方程等一系列齒面分析所必須的數學公式，並深入研究了蝸桿副齒面接觸線的演算法，為蝸桿副的三維數字化造型打下了堅實的數學基礎。 -
Boundary integral equation of electromagnetic field with line current element of external source
存在外源線電流元的電磁場邊界積分方程 -
Results indicate that with the approximation of _ ( 0 ) _ ( 0 ) - grtlneisen equation of state is usable to describe the release isentrope of ofhc copper in the present pressure range. in addition, the difference ( w - 2u ) becomes greater with the increase of shock pressure, where w is the measured particle velocity at the final release state ( 1 atm ) and 2u is computed from the mirror line of hugoniot
卸載路徑的計算和分析表明：在所研究的壓力范圍，無氧銅的等熵卸載過程用gr neisen狀態方程在_ 0 _ 0 =近似下的描述是適用的；卸載到一個大氣壓的終態粒子速度w與鏡像反演的粒子速度2u的偏差，隨沖擊波壓力的增加而增大。 -
3 - d ift have three fin arrangements : staggered arrangement fins, in - line arrangement fins and spiral arrangement fins. the former experimental study regressed the experimental data of all three fin arrangements and obtained the heat transfer criterion equation of 3 - d ift, while the paper sets apart the three mixed fin arrangements and applies othorgonal testing method to the 3 - d ift with staggered arrangement fins which is wide used in the engineering
原有的研究是將三種肋排列形式三維內肋管的實驗數據混雜在一起進行回歸得到三維內肋管的換熱準則式，而本文則將原有研究中混雜不清的肋排列的三種形式區分開來，並對其中在工程中應用最廣泛的肋叉排三維內肋管進行了詳細的正交試驗研究。 -
The main job of this research is : ( 1 ) analyze the operation situation of power system during faults ; pay attention to the traveling wave on the three - phase transmission line ; study the equation of voltage on three - phase transmission line with impedance capacitance coupling between phases ; contact the voltage on any point with the fault voltage, study the singularity of the voltage signal in fault point, and make it to be the base of the new fault detection method ; ( 2 ) apply the singularity detection theory based on wavelet analysis to the power system faults detection, give a complementary criterion to current fault detection criterion, study how to select the basic wavelet, how to filter noise, how to detect the singular point or fault point, and finally give a total solution. the simulations prove it to be a quick, correct and effective fault detection method
本文的主要工作有： （ 1 ）分析電力系統在發生故障時的運行狀態，尤其對三相傳輸線上的故障行波進行了分析和研究，推導了考慮相間耦合的三相傳輸線電壓方程，並將傳輸線上任一點的電壓與故障點電壓建立起聯系，得出了傳輸線上電壓信號在故障點處的奇異性，並以此作為構造新的故障檢測演算法的理論基礎； （ 2 ）將基於小波變換的信號奇異性檢測理論運用於電力系統故障檢測中，針對目前相關研究的不足，提出了電力系統故障檢測判據的補充判據，通過對基本小波的選擇、除噪措施、信號奇異點也即故障點的檢測方法所作的分析，給出了一個可行的解決方案；模擬研究表明：這是一個快速、準確、有效的故障檢測演算法。 -
Based on conjunction theory, the models for gear manufacturing is developed, and the equation of the gear surface is gained by the equation of rack cutter. the contact line in manufacturing and the tooth profile of the gear is also discussed based on the equation of the gear surface
本文首先基於齒輪嚙合原理，建立了齒輪加工的模型，由刀具曲面方程推導出被加工齒輪的齒面方程，並進一步推導出齒輪端截面的齒廓方程和齒輪刀具接觸線方程。 -
2. the transmission line model of integrated inductors are presented and the procedure of extracting parasitic parameters of integrated inductors are induced to created an equation of parasitic parameters. a series of planar spiral integrated inductors are designed and fabricated
設計和制備了一組常規平面螺旋電感，並測量了其s參數，研究了電感量， q值的計算方法，計算了常規平面螺旋電感的各種參量，對實驗結果進行了詳細的分析和研究。 -
The numerical simulation for adjustable - blade pump on - line autoregulation in diversion works has been studied in this paper whose background is modification works of dongjiang - shengzhen diversion works. the problems include autoregulation on water height of the fore bay in single pump station, autoregulation on output of adjustable - blade pump in single pump station, and autoregulation on flow equation of multilevel pump stations
本論文以東江深圳供水改造工程為背景，對輸水工程中應用轉槳泵進行在線自動調節數字模擬進行了研究，其中包括單級泵站中對前池水位進行自動調節，單級泵站中對轉槳泵的輸出流量進行自動調節，以及多級泵站輸水系統流量平衡自動調節。 -
Only using data of single - terminal, the algorithm can eliminate the influences of the fault resistances and it need n ' t resolve the complicated equation of long line
這種方法僅採用線路的單端數據，不受故障過渡電阻的影響，無需求解復雜的長線方程。 -
The flood and drought in both first stage and second stage of rainy season in fujian province were forecasted by the ways of line regression prediction equation and three kinds of artificial neural network models, the results show : the backpropagation ( bp ), radial basis function ( rbf ) and elman neural network models are much better than line regression prediction equation in historical sample fittings, independent sample test, actual prediction ability
（ 3 ）運用線性回歸預報方程和三種人工神經網路模型對福建汛期旱澇進行預測的實驗表明： bp 、徑向基（ rbf ）和elman這三種人工神經網路模型在歷史樣本擬合精度上、獨立樣本檢驗結果和網路模型的實際預測能力上都明顯優于傳統的線性回歸方法。 -
The model can be made into difference equation of the temperature field that can be used to simulate calculation ; then we can get the set of edge point, and we can have the function of the fire line, and we can also have the burned area, the length of fire line and the space of fire area ; it also come to the conclusion that the main factor of forest fire is convection heat transfer
經差分處理，得到進行模擬計算的一組溫度場計算方程；由邊界點條件，求出邊界點的集合后，擬合得出火線函數，積分后可得到時刻火場的過火總面積、火線長度和火場形狀，同時進一步證實了對流傳熱方式是影響林火蔓延的主要因素。 -
Several transient simulation programs have been developed based on the models above, and were put into practice of the transient simulations of following : ( 1 ) autoregulation on water height of the fore bay in single pump station, and the influence of governor parameters ; ( 2 ) autoregulation on output of adjustable - blade pump in single pump station, and the influence of governor parameters ; ( 3 ) on - line autoregulation on flow equation of multilevel pump stations system
本文應用上述方法編制了過渡過程模擬程序， （ 1 ）進行了單級泵站中轉槳泵在線自動調節泵站前池水位的動態模擬計算，並對調節參數的影響做了比較研究； （ 2 ）進行了單級泵站中轉槳泵在線自動調節泵輸出流量的動態模擬計算，並對調節參數的影響做了比較研究； （ 3 ）進行了多級泵站中轉槳泵在線自動調節輸水系統流量平衡的動態模擬計算。 -
The transmission line equation is the basic equation of the transmission line theory and is an important equation from lumped parameter circuit to distributed parameter circuit in the circuit theory
傳輸線方程是傳輸線理論的基本方程，是電路理論中由集中參數電路過渡到分佈參數電路的一個重要方程式。 -
Technology of non - damage test for concrete intensity is extensively applied in project testing, as a precise and direct approach. accordingly, the test in this essay makes use of average concrete samples made up of commo - n raw material in boutou, and adopt comprehensive method of ultrasonic elasticity to test the concrete used within one year in boutou. through the regression analysis, we get the regression equation of anti - intensity of these two materials under the given conditions. according to the result, we establish the accurate curve line for comprehensive method of ultrasonic elasticity and provide practiced and non - damage testing approach and calculating method for concrete intensity test and reference for testing staff concerned
混凝土強度無損檢測技術作為一種簡便快捷準確的測強技術在工程檢測中得到了廣泛的應用，鑒於此，本次試驗通過採用包頭地區常見原材料製成的一定批量常見齡期的不同種類（指混凝土試塊中的粗骨料、混凝土強度等級不同）普通混凝土標準試塊，採用回彈?超聲綜合法對包頭地區齡期不超過一年的現場混凝土進行了大量的試驗，並利用回歸分析，給出兩種骨料混凝土在相應測強條件下的立方體抗壓強度回歸方程，根據實驗結果建立包頭地區精度較高的混凝土回彈?超聲綜合法基準測強曲線，為實際工程的混凝土現有強度評定提供簡單易行的無損測試方法和計算方法，供有關檢測人員參考使用。 -
Based on unified strength theory, the boundary line equation of surrounding rock mass plastic zone under non - uniform stress field was deduced, and it can be used to pre - estimate the dimensions and shapes of underground tunnel ' s plastic zone with different coefficients of horizontal pressure
摘要基於統一強度理論，推導出非均勻應力場的巷道圍巖塑性區邊界線方程式，可用於預測不同側壓系數時地下深埋隧洞的塑性區大小及形狀。 -
The cauchy problem for a hyperbolic equation of second order equation with data on the parabolic line
取值在拋物線上的雙曲型微分方程的柯西問題 -
On the basis of the research achievements of the predecessors, combing the research object, that is spherical indoor space, this thesis adopts energy - area method and the equation of the wrap - up line analyzing and researching deeply on the acoustics wave reflection features of spherical indoor space
在總結前人研究成果的基礎上，結合本文的研究對象球形室內空間，採用聲能面積法和包絡線方程從理論上深入分析研究球形室內空間的聲波反射特點。
分享友人