equivalent cantilever 中文意思是什麼

equivalent cantilever 解釋
等效懸臂梁
  • equivalent : adj 1 相當的，相同的，同等的。2 【化學】等價的，當量的；【數學】等價的；等量的；等勢的；【物理學...
  • cantilever : n. 1. （橋梁的）懸臂，肱梁；支架。2. 電纜吊線夾板；紙條盤。
  1. Practical method for calculating equivalent wind loads on double cantilever bridges

    等長雙懸臂梁等效風荷載實用計算方法
  2. The content of this thesis comes from the fujian natural science found following research task 。 it studies on a space cantilever single beam attached to a moving support 。 inertia forces which are brought by the support ' s movement ， are acceded to the equivalent initiative forces and the equivalent initiative moments 。 when we consider the relation of the forces and deformation ， we change the method of material mechanical analysis to the elastic mechanical analysis 。 further more ， we discusses the feasibility of the method which uses the multi - rigid - body discrete model to simulate the dynamic characteristic of a elastic body 。 first ， the finite segment method is adopted to establish the models of the beam 。 based on kane ' s equations ， dynamic math - model for the beam are derived 。 and by use of c - language and runge - kutta procedure ， the computer - oriented procedure can give the whole responses of the beam 。 second ， with compare to the numerical examples ， the method which uses the multi - rigid - body discrete model to simulate the dynamic characteristic of a elastic body which is under the condition of movement is verified to be feasible 。

    本論文為福建省自然科學基金后續研究課題，以已知支撐運動的單個空間懸臂梁為對象，在等效主動力與等效主動力矩中加入支撐轉動引起的慣性力，並在考慮力與變形關系時，用更一般的彈性力學分析代替材料力學分析，進一步研究用多剛體離散模型來模擬其動力學特性的可行性。首先，用有限段建立機械臂的多剛體離散模型，用kane動力學方法建立其動力學方程。並用c語言編制演算法程序，採用了四階runge - kutta積分程序求解微分方程組，給出構件的全部動態歷程。
  3. Fabrication process of the microgripper based on silicon bulk micromachining is designed. effects of footing and lag in icp and bonding failure are discussed as emphases. the cantilever type gripping finger that is 6 m wide and 5471 m in equivalent length was released successfully characteristic of comb - drive electrostatically actuated microgripper is tested

    進行了大量的工藝試驗和分析，特別對大深寬比的超長長度懸臂梁型夾持臂及梳狀驅動結構進行了深入研究，解決了微細加工工藝中的關鍵技術。
  4. The whole building can be equivalent to a cantilever bar, and the structural total displacements can be divided into parallel displacement and rotational displacement based on the harmonize condition of displacement, and the parallel shear and the rotational shear of the elements can be accordingly obtained by selecting the renegade body from top to bottom in turn

    根據位移協調條件，將結構的位移分解成平動與轉動成分，得到相應的結構平動時構件所承擔的剪力與結構轉動時構件所承擔的剪力，再根據力的平衡條件，推導出雙向地震作用下考慮構件抗扭剛度時結構的線彈性扭轉角，並對構件的剪力及變形進行了修正。
  5. Then analyse the feature of mems switch and gives a equivalent model of cantilever mems switch to analyse its characteristics. at last, a mems multi - frequency reconfigurable pifa is designed and simulated

    之後對mems開關進行了研究，並給出了懸臂梁式mems開關的模擬模型，利用此模型分析了各參數對于mems開關傳輸特性的影響。
  6. Though the contrast of the algorithm used in cantilever lattice structure and cantilever solid web beam, we can get the algorithm that can be used to calculate the equivalent inertia moment of the lattice structure when it is regarded as solid web beam

    並進一步延伸到四肢格構式構件等效慣性矩的計算，給出了四肢格構式構件等效為實腹式構件時，等效慣性矩的計算公式。
分享友人
分享到 Line

分享到臉書