evenly distribution 中文意思是什麼

evenly distribution 解釋
均勻分佈
  • evenly : 公平地
  • distribution : n 1 分配，分發，配給；分配裝置[系統]；配給品；配給量；【經濟學】配給方法，配給過程；分紅；【法律...
  1. The gas field in pemfc means the gas distribution in gas source, gas inlet tube ( scale of m ), gas - blower, gas manifold ( scale of cm ), channel ( scale of mm ), diffusion layer ( scale of um ), hydrophobic layer and catalyst layer ( scale of nm ). the aim of changing the scales is to make oxygen reach reaction area as evenly as possible

    Pemfc的氣場指在氣源、進氣管（分米級） 、風機、進氣箱（厘米級） 、流道（毫米級） 、擴散層（微米級） 、疏水層（亞微米級） 、催化層（納米級）中的氣體分佈，每一級尺度的變化是為了氣體的進一步均勻化。
  2. Abstract : it has been established that titanium exists in jinduicheng molybdenum deposit in rutile type by test for all kinds of ores. its grade is about 1 %. there isn ' t concentration in products. the particle size is fine, and the distribution isn ' t evenly. it has a definite economic benefit if it recoveried from tailings

    文摘:通過對金堆城鉬礦床中各種類型礦石的系統測試，查明了鈦在該礦床中主要以單礦物金紅石的形式存在於花崗斑巖各蝕變帶的鉬礦礦石中，品位約為1 % ，產品中沒有富集，基本隨尾礦流失，粒度細，分佈不均，從尾礦中進行綜合回收，具有一定的經濟效益。
  3. Results : there was no significant effect on the stress distribution in the supporting tissue according to the different numbers of abutments at the central occlusion, and there was an evenly stress distribution in the abutment and alveolar membrane of the area around the missing teeth

    結果:基牙和人工牙在正中咬合時，基牙數目對支援組織的應力分佈無明顯影響，且基牙利牙槽幡頂黏膜的應力分佈均勻。
  4. 3 the luminous intensity of daylight signalling lamps should have its maximum in the centre of the luminous intensity distribution. it should decrease evenly from the centre of luminous intensity distribution

    白晝信號燈的發光強度最大值應位於發光強度范圍的中心，並應均勻地自中心向發光強度范圍內減少。
  5. Block e cases appeared earlier in the outbreak and showed a point - source type of distribution. cases in other blocks which appeared 3 days later were more evenly spread out in time

    E座個案傾向在爆發初期發生，並呈現點源分佈模式，其餘各座樓宇個案的發病時間則在3日後，而且分佈得較為平均。
  6. The results of the malvern laser analytical apparatus and sem also show that by adding a kind of surfactant into the reacting vessel, a evenly grain distribution precursor particl e that has a average grain size about 0. 5um can be obtained

    在反應中加入表面活性劑，用malvern激光粒度檢測儀和掃描電鏡觀察粉體的粒度及分佈狀態，可看出平均粒度在0 . 5 m左右的前驅體粉末分佈均勻，分散良好。
  7. The smaller the the difference of the temperature of feedwater and backwater is, the more evenly and slowly the temperature distribution is. the smaller the thickness of overburden layer and the distance of two tubes are, the more evenly and slowly the temperature distribution is

    在供回水溫度和覆蓋層厚度均不變的條件下，排管間距越小，其溫度分佈越為平緩，地板表面的溫度分佈也越為均勻，地板表面平均溫度也越高。
  8. Node evenly distribution ( super peer and normal peer ). 2. classification of nodes - accounting heterogeneity

    主要的技術內容如下: 1 .節點均勻分佈（超級節點和普通節點） 。
  9. For the membranes modified by fe2 + / ooh initiation, the grafted hydrophilic polymers on the membranes surface has a more evenly distribution and a smoother surface morphology than that of the membranes modified by uv initiation. chondrocyte culturing was performed to evaluate the cytocompatibility of the control and the modified plla membranes

    與紫外光引發接枝聚合所得到的plla改性膜相比，由fe ~ （ 2 + ）輔助引發接枝聚合所得到的plla改性膜表面的親水性聚合物的分佈更為均勻，表面粗糙度較低。
  10. The performance of usscd is compared with the well known algorithm, icollide, through a series of experiments. the results show that, when the objects are evenly distributed, and the number of objects is large, the performance of usscd is better than that of icollide. in this paper, a class of non - uniform spacial subdivision method is proposed, which is composed of two steps : first, the space is coarsely subdivided non - uniformly, based on the distribution density of the objects, then, every subspace is uniformly subdivided

    提出了一種基於均勻空間分割的快速碰撞檢測演算法usscd ，與經典的icollide演算法進行了對比試驗，試驗結果表明，在物體均勻分佈的情況下，隨物體數量的增多， usscd表現出明顯的優勢；提出了一類非均勻空間分割方法，在該方法中，空間分割由基於密度的非均勻空間分割和對每個子空間進行均勻分割兩個步驟實現；提出了一種基於投影的非均勻空間分割方法。
  11. When the eccentricity distance is different, the distribution form of average pressure density in machining zone is given. in the lapping and polishing experiment, sic materials can be evenly removed by choosing reasonable process conditions and parameters, and the surface will convergence to prefect shape. this is helpful to the study on quantificational machining technologies of aspheric components

    主要內容和創新點包括： 1 、根據平面研拋的成形原理和材料去除特點，建立了工件表面相對運動軌跡的數學模型，給出了不同偏心條件下加工區域的平均壓強分佈形式；在sic工件的平面研拋實驗中，通過選擇合適的加工條件和對工藝參數進行調整，能夠實現表面材料的均勻去除，獲得理想的工件面形，同時也為非球面確定量研拋提供工藝指導。
分享友人
分享到 Line

分享到臉書