expansion joint 中文意思是什麼
expansion joint
解釋
【建築】伸縮（接）縫。-
Jxf flexible dirt - filteration expansion joint
Jxf型可曲撓濾污伸縮接頭 -
Technical standard of thermal packer and expansion joint
注蒸汽封隔器及井下補償器技術條件 -
Jxf flexible dirt - filteration expansion joint - changmao
Jxf型可曲撓濾污伸縮接頭- changmao -
Composition cork - expansion joint fillers - test methods
復合軟木.膨脹連接填充料.試驗方法 -
Standard specification for preformed sponge rubber cork and recycled pvc expansion joint fillers for concrete paving and structural construction
混凝土鋪面和結構建築用預制微孔橡膠軟木和可回收的pvc膨脹接縫填料的標準規范 -
Bellows expansion joint
波形膨脹節 -
Aim at to turn a dense oil pump in the movement the metal bellow expansion joint and buffer tank was installed in the dense oil pump export because of the violent vibration and noise cause by the discharge and the pressure pulsation, the result show lowered the vibration and noise availably was obvious
摘要針對轉子式稠油泵在運行中因流量和壓力脈動所引起的劇烈震動和噪聲，在稠油泵出口安裝金屬伸縮節和緩沖罐，有效地降低了震動和噪聲。 -
Abstract : a manufacture method of a major diameter circline weldless u - expansion joint by hydrostratic forming is introduced, a calculation formula of loading with hydrostratic forming is given by stress analysis
文摘:簡要介紹了液壓成型大直徑無環焊縫u形膨脹節的方法，通過應力分析，給出了液壓成型的加載內壓計算公式。 -
Composition cork - expansion joint fillers - specifications, packaging and marking
復合軟木.膨脹連接填充料.規范包裝和標記 -
Standard specification for preformed expansion joint filler for concrete bituminous type
混凝土用預制膨脹接縫填充料 -
Test methods for preformed expansion joint fillers for concrete construction nonextruding and resilient types
混凝土結構用預制膨脹接縫填料的試驗方法 -
Standard specification for preformed closed - cell polyolefin expansion joint fillers for concrete paving and structural construction
混凝土面層和結構建造用預制閉孔聚烯烴伸縮接頭填充料的標準規范 -
Standard specification for preformed expansion joint filler for concrete paving and structural construction nonextruding and resilient bituminous types
混凝土鋪面和結構建築用預制伸縮縫填料的標準規范 -
Construction management of expansion joint of bridge on highway
高速公路橋梁伸縮裝置施工管理 -
The whole system is supported by the main jack arrangement when concreting, placed at the front supporting bracket and the ( rear ) suspension gallows ? or on supporting brackets only at the start and expansion joint spans
整個系統在混凝土澆注過程中由前牛腿及（后）吊架上主千斤頂系統支撐，在起始段和伸縮縫處則在前後牛腿處支撐。 -
Our company is a sino - korea joint venture that mainly produce rubber joint, steelless and steel expansion joint, our products have all kinds of different type, including german standard, america standard, japan standard, england standard and so on. our products have been exported to spain, france, italy, kroea, dubai, england, japan, america, egypt, vietnam and so on
公司地處鄭州洛陽之間，中西部「百強縣」鞏義市境內，隴海鐵路310國道開洛高速橫貫東西。詩聖杜甫故里，西可觀洛陽牡丹，南遊少林，北臨黃河。物華天寶，人傑地靈，通訊發達，交通便利，實為投資創業之佳境。 -
The modes selection of directly buried installation for hot - water heat - supply pipeline, the design and construction of directly buried installation with and without expansion joint and the quality assurance of prefabricated directly buried insulating pipe are discussed with a practical engineering example
摘要結合工程實例，探討了熱水供熱管道直埋敷設方式的選擇，有補償和無補償直埋敷設方式的設計與施工及預制直埋保溫管質量的保證。 -
Analysis on the causes of damage, this paper modified the meijia bitumen materials in order to enhance the low temperature capacity of bitumen and bituminous mixture through the polymer. emphasis on the study of low temperature capacity of modified asphalt and bituminous mixture, we utilize reasonable construction craft to avoid the cracks problem between bituminous mixture and bridge and give a advance way of small or moderate span bridge expansion joint in low temperature areas
針對這一缺陷，本文通過添加熱塑性橡膠類改性劑和橡膠類改性劑，對美佳改性瀝青結合料進行二次改性，重點研究了改性后瀝青結合料和混合料的低溫性能，並採用合理的施工工藝解決填縫料與梁端間存在的界面裂縫問題。 -
The key factors affecting the stagnation point position of l - type pipeline section are the setting position of bellows type expansion joint and the bend angle degree
影響水平轉角管段駐點位置的主要因素為波紋管補償器設置位置、彎頭角度。 -
The calculation of stagnation point position of straight pipeline section with both movable ends and l - type pipeline section with bend at one end and bellows type expansion joint at other end is discussed
摘要探討了兩側為活動端的直管段及一側活動端為彎頭，而另一側活動端為波紋管補償器的水平轉角管段駐點位置的計算。
分享友人