fiber reinforcement 中文意思是什麼

fiber reinforcement 解釋
纖維強化熱固性/纖維強化復合材料
  • fiber : n. 〈美國〉 ＝ fibre。
  • reinforcement : n. 1. 增強，加固；補強物，強化物；補給品。2. 增援，支援；〈pl. 〉增援部隊，援軍；救援艦。
  1. Thus the use of steel fiber reinforcement concrete in corbel can avoid complicated calculating in design, and the diminish difficulty of construction, at the same time when corbel ' s dimension can not be increased the reinforcement concrete corbel ' s ultimate load capacity and anti - seismic performance can be improved by the addition steel fiber into concrete. this method has become a kind of applied method and is highly concerned by the domestic and international academe and engineer group

    因此，在配筋密集的牛腿中使用鋼纖維混凝土可以避免設計時繁雜的配筋計算、減小施工難度，同時在牛腿截面尺寸不能增大的情況下，可以通過加入鋼纖維來提高鋼筋混凝土牛腿的承載力和抗震性能，用鋼纖維加入鋼筋混凝土牛腿已成為一種實用方法受到了國內外學術界和工程界的極大關注。
  2. ( 1 ) systematic triaxial compression tests are made for the sand reinforced by various national geosynthetics. comprehensive investigations into the interaction characteristics are also made between sand / lime fly ash and various national geosynthetics by direct shear tests and pull out tests, which can help choosing geosynthetic type and understanding the geosynthetic reinforcement mechanism ; ( 2 ) this paper is also firstly systematically presents the results of a comprehensive investigation into the interaction characteristics between lime fly ash and various national geosynthetics ; ( 3 ) by non - linear fem, the influence of the modulus of geosynthetics, the thickness of the soft ground and the width of the foundation on the effectiveness of geosynthetic reinforcement are also studied ; ( 4 ) the main conclusions are as followed : ( geotextiles are likely to be suited for projects allowing high displacement, polyester warp knitting geogrids and oriented geogrids for projects allowing medium displacement, glass fiber geogrids for projects allowing low displacement and geonets for secondary projects. ( the confining effect of fill material to act on different kinds of geosynthetics varies largely, which must be considered

    （ 1 ）本文利用三軸壓縮試驗，比較各種國產土工合成材料對砂土的加筋效果；利用直剪試驗和拉拔試驗，比較各種國產土工合成材料與砂土或石灰粉煤灰的界面摩擦特性，深入研究土工合成材料的加筋機理，首次明確提出加筋土工合成材料的選型原則； （ 2 ）本文首次系統地研究了石灰粉煤灰與各種國產土工合成材料的界面摩擦特性； （ 3 ）本文採用有限元法，系統研究了加筋模量、軟土地基厚度、基礎寬度等因素對土工合成材料加固軟土地基效果的影響； （ 4 ）本文主要結論如下： （無紡土工織物適合用於允許大變形的加筋土工程；滌綸纖維經編土工格柵和塑料拉伸土工格柵適合用於對變形有較嚴格要求的加筋土工程；玻璃纖維經編土工格柵適合用於對變形有嚴格要求的加筋工程；土工網適合用於低等級的加筋土工程。
  3. To produce cylinder by woven edge and glass fiber with twisting to each other, then producing composites reinforcement through the process of resin permeating, gelatin and heat designing

    將廢布邊及玻璃纖維在施予一張力下加?完成長條圓柱狀，再經過含浸、膠化及熱定型等過程製成復材鋼筋。
  4. Some manufacturers use fiber reinforcement to control plastic shrinkage and thermal cracking

    一些生產商使用纖維增強來控制塑性收縮和熱脹開裂。
  5. The main products include fiber glass yarn, fiber glass fabric, rpgb - tape, fiber glass reinforcement for grinding wheel, texturing of yarn, winding roving, smc roving, chopped strands and so on

    主要產品有無堿玻璃纖維紗、布（含用於電氣和玻璃鋼製造業的脫臘處理布） 、帶，玻璃纖維增強砂輪布，膨體紗，纏繞紗， smc ，短切原絲以及各類玻纖網布鋁過濾布等等。
  6. According to the mechanic and ballistic properties test, the kevlar fiber and phenolic resin are chose as the reinforcement and matrix respectively

    並通過對增強材料力學性能、及防彈性能的測試分析，確定了防彈芳綸纖維增強材料。
  7. Patterned, water - activated paper tape with fiber reinforcement. the pattern can be anything that will help identify when a carton seal has been broken. tape must not interfere with carton markings

    牛皮紙防水封箱膠帶：當箱子上的任何封口膠帶破裂時，很容易被辨別出來，但封箱膠帶不能封到箱嘜上。
  8. Layer steel fiber reinforced concrete ( lsfrc ) of pavement is a new composite pavement material which both cherishes the reinforcement of steel fibers to the concrete and cuts the costs

    層布式鋼纖維路面混凝土是一種既利用了鋼纖維的增強性能，又節約了工程造價的新型的復合式路面材料。
  9. Until now, the domestic and overseas scholar has studied the factors that have effect on performance of steel fiber reinforced concrete corbel such as shear span to depth, strength of concrete, reinforcement ratio ( including longitudinal reinforcement and stirrup ) and ratio of horizontal to vertical load. for calculating the cracking load, and ultimate load domestic and foreign scholar has brought forward a series of calculative formulas and methods have been put forward that based on statistical analysis, flexural model and truss model

    到目前為止，國內外學者已研究了剪跨比、混凝土強度、配筋率（包括縱向鋼筋和箍筋） 、水平荷載與垂直荷載之比等因素對鋼筋鋼纖維混凝土牛腿受力性能的影響，對牛腿的抗裂計算和承載力的計算，國內外學者曾提出了基於數理統計分析、彎壓模型和桁架模型等的一系列計算方法和計算公式。
  10. We are a leading global supplier of high - tenacity polyester fiber and other advanced materials that are used in automobile tire reinforcement, engineered reinforcements, broad and narrow woven fabrics and rope

    我們是首屈一指的全球供應商，提供高強力聚酯纖維和其它先進的材料，用於汽車輪胎及工程增強骨架材料寬幅和窄幅織物和纜繩。
  11. Now reinforcement and improve toughness is the core topic study of the ceramic materials, and fiber reinforcement is the most obvious method, it can improve not only the toughness but also the hardness of materials

    目前研究陶瓷材料的核心課題是補強增韌，而纖維增韌是目前補強增韌方法中效果最為顯著的方法，它在提高材料韌性的同時，在大多數情況下還能提高材料的強度。
  12. The application of carbon fiber reinforced plastic in frame beam reinforcement of one factory building

    某廠房框架梁加固中碳纖維的應用
  13. During the above iteration, the stress resultants of the concrete in the cross section are evaluated by integrating the concrete stress - strain curve over the compression zone, while those of the structural steel and the steel reinforcement ( if any ) are obtained using the fiber element method

    迭代計算過程中混凝土的截面抗力通過對混凝土應力-應變曲線在截面上的精確積分求得，而型鋼和鋼筋部分的截面抗力則採用纖維元方法求得。
  14. Based on the test of 3 concrete beams reinforced with surface adhering sand carbon fiber bar and 2 concrete beams reinforced with surface adhering sand glass fiber bar, the deflection, balanced reinforcement ratio, failure mode, and ultimate capacity were analyzed and corresponding formulas are recommended

    摘要以3根粘砂碳纖維聚合物筋混凝土梁和2根粘砂玻璃纖維聚合物筋的試驗為依據，分析了纖維聚合物筋混凝土梁的撓度變形和破壞形式，以及界限配筋率和正截面承載力；並結合我國混凝土結構設計規范對梁的正截面承載力計算公式進行了推導。
  15. An experimental study on steel fiber reinforced concrete ( sfrc ) thick cap with four piles indicates that the factors affecting its ultimate loads are composed of its effective thickness, steel fiber volume ratio, concrete strength grade, shear span length, steel ratio and the form of reinforcement, in which the factor of the form of reinforcement affecting the ultimate loads of pile cap is distinct

    摘要鋼纖維混凝土四樁厚承臺的性能試驗研究結果表明，影響其極限荷載的因素主要有承臺有效厚度、鋼纖維體積率、混凝土基體強度等級、承臺的剪跨比、縱向鋼筋配筋率和配筋形式等，其中，配筋形式對鋼纖維混凝土厚承臺承載力的影響是很顯著的。
  16. The followings are carried out for ballistic composite with resin matrix to realize its double function of loading and bulletproof and meet various tactics technology demands in the paper 1. the resin and reinforcement for arms ballistic system are selected and ballistic properties for composites with different resin matrixs ( improved phenolic, polyethylene, rubber, bi - phenol - a, and biamaleimide ) and different fibers ( kevlar, glass, carbon and uhmwpe fiber ) are investigated, with the aim of maxwell model to explain the matrix match principle for ballistic composites

    1 、本論文從材料選擇入手，進行了復合裝甲防彈體系用樹脂、增強材料進行了選擇和研究，考核了不同樹脂類型（改性酚醛、聚乙烯、橡膠、雙酚a環氧和雙馬來酰亞胺體系） 、不同纖維（ kevlar纖維、玻璃纖維、碳纖維、高強聚乙烯纖維）復合材料的防彈性能，並引入maxwell模型較好地解釋防彈復合材料的基體匹配原理。
  17. It was found that the permeability of fibrous reinforcement mainly lied on the preform architecture. the distribution of void region and fiber volume fraction in the perform had important effects on permeability

    文中對lcm纖維增強材料預成型過程中常見的兩大纖維鋪敷缺陷? ?流道效應及剪切變形情況下的滲透特性進行了研究。
  18. The distortion of in - plane fibers is considered to be the main reason for the effect of stitching on the in - plane mechanical properties, and the fiber distortion region, the resin - rich pocket and the through - thickness reinforcement section are taken into account. the fiber misalignment angle and the inhomogeneous fiber volume fraction caused by stitching have been determined within the lamina. the elastic constants of a lamina are calculated using a micromechanical model, then the constitutive equations of the stitched composite laminates can be composed

    從縫紉孔附近纖維變形的細觀結構出發，建立的纖維彎曲模型，以面內纖維的彎曲變形作為縫紉影響層合板面內力學性能的主要原因，同時考慮了纖維變形區、厚度增強區以及樹脂富集區的影響，得到單向板內任意一點處的纖維偏轉角和纖維體積百分含量。
  19. Preparation of reinforcement of aramid fiber and fiberglass

    關于加固混凝土用混雜纖維復合材料耐久性的討論
  20. The term fiber glass molding correctly refers only to products involving a resin and some form of glass fiber reinforcement

    術語「玻璃纖維模塑」僅僅是指樹脂與一些玻璃纖維增強的產品。
分享友人
分享到 Line

分享到臉書