filling bar 中文意思是什麼

filling bar 解釋
污跡
  • filling : n. 1. 裝滿,填裝;填補。2. 填料;填土。3. (糕點內的)餡。4. (織品的)緯紗,漿料。
  • bar : BAR = Browning automatic rifle 白朗寧自動步槍。n 巴爾〈南斯拉夫港市〉。n 1 棒,桿,條;棒狀物。2...
  1. Planting bar used syringes from the bottom of the hole to put adequate amounts of external uniform adhesive filling injection hole, pay attention not to air hole inclose

    使用植筋注射器從孔底向外均勻地把適量膠粘劑填注孔內,注意不要將空氣封入孔內
  2. The variations in trace element contents and ratios may hold up a mirror to the lake - level fluctuations and climatic changes, which, in turn, have exerted a direct and important effect on the sequence stratigraphic development. collectively, the reservoir rocks from the yanchang formation consist dominantly of the delta front subfacies subaqueous distributary channel and channel - mouth bar microfacies and delta plain subfacies subaerial distributary channel microfacies fine - grained feldspar sandstones and siltstones. the reservoir rocks have been subjected to three stages of diagenetic and porosity evolution : ( 1 ) the porosity reduction by the mechanical compaction and chemical pressure solution during the early diagenetic stage ; ( 2 ) the porosity increase by the dissolution during the a substage of the late diagenetic stage, and ( 3 ) the porosity reduction by the cementation and filling during the b substage of the late diagenetic stage

    系統的儲層特徵研究表明,該區延長組儲層成因類型主要為三角洲前緣水下分流河道、河口砂壩及三角洲平原水上分流河道微相細粒長石砂巖、粉砂巖;儲層巖石經歷了壓實,膠結,溶蝕等成巖作用,歷經早成巖機械壓實和化學壓溶孔隙縮小期、晚成巖a亞期溶蝕作用孔隙擴大期及晚成巖a亞期( b亞期)膠結充填孔隙縮小期三個成巖-孔隙演化階段;儲層物性總體上具有較低孔滲、低孔滲的特點,孔隙類型主要為粒間溶孔、殘余粒間孔隙、粒內溶孔、晶間孔及晶間溶孔,裂縫不發育,儲集巖排驅壓力和中值壓力較高,孔隙結構類型以細小孔-微孔隙,微細喉-微喉型為主。
  3. Construction technique of pressure filling concrete to still pipe inner arch of 75m span tie bar arch bridge

    系桿拱橋鋼管拱內混凝土的壓注施工工藝研究
  4. Road tankers. road tankers containing liquefied chlorine and sulphur dioxyde. devices for filling and emptying at the top, for a maximum service pressure of 14. 5 bar

    道路罐車.液態氯和二氧化硫道路油罐.最大工作壓力為14 . 5bar從頂部裝卸的裝置
  5. In this paper are analyzed the causes of light filling bar in weaving fine viscose / flax fabric caused by machine and operation with the technical measures to minimize this defect and the achieved result detailed

    摘要分析了織造過程中機械故障和操作過程中造成粘麻細布稀密路疵的原因,具體介紹了降低稀密路疵點的技術措施和所取得的效果。
分享友人