filling of mold 中文意思是什麼

filling of mold 解釋
裝模
  • filling : n. 1. 裝滿，填裝；填補。2. 填料；填土。3. （糕點內的）餡。4. （織品的）緯紗，漿料。
  • of : OF ＝Old French 古法語。
  • mold : mold ＝ mould.
  1. Different parameter variation caused by energy distribution duri ng die casting process shows that high energy filling mold is the key to insuring quality of die casting

    從壓鑄過程中能量分配引起的各種參數變化，說明高能充型是保證壓鑄件品質的關鍵。
  2. The results show that the heat preservation coating and its proper thickness are favorable to the enhancement of filling mold speed of aluminium alloy ; the higher the pouring temperature is and the larger the ratio of hollow areas of vertical pouring is, the faster the speed of filling mold of aluminium alloy is ; if the mold is too thick or too thin, it may decrease the speed of filling mold ; the proper length and the area of vertical pouring are favorable to the enhancement of the speed of filling mold ; although negatire - pressure may improve filling the speed, too high negatire - pressure may enlarge the flaw in casting

    結果表明：保溫塗料及一定的塗層厚度有利於提高鋁液的充型速度；澆注溫度越高、直澆道空心面積率越大，鋁液充型速度越快；模樣厚度太厚或太薄，均會使鋁液充型速度降低；一定的直澆道長度及直澆道面積有利於提高鋁液的充型速度；施加負壓會使鋁液的充型速度大大提高，但負壓過大會增大鑄造缺陷。
  3. Computer simulation and actual experiments of rtm mold - filling process affected by processing parameters

    工藝參數對樹脂充模過程影響的模擬與實驗研究
  4. Analysis on defects and filling process of tial based alloy exhaust valve during the centrifugal foundry process in permanent mold

    基合金充型過程及排氣閥門內部缺陷分析
  5. Semi - solid forming of aluminum is finding its main niche today in its growing ability to 1 ) control metal viscosity and hence mold filling behavior, 2 ) reduce die casting cycle time, 3 ) improve die life, 4 ) improve casting soundness and quality, and 5 ) produce parts at acompetitive cost

    由於鋁半固態成型技術能更好地1 ）控制金屬粘性和模具填充性能2 ）減少壓鑄生產周期3 ）增加模具壽命4 ）改善壓鑄質量5 ）使生產的零件價格具有競爭性，因此目前有重要的使用價值。
  6. Abstract : thermally induced stress and the relevant warpage cause by inappropriate mold design and processing conditions are problems that confounded the overall success of injection molding. a thermorheologically simple thermoviscoelastic two - dimension material model is used to simulate the residual stress and warpage within injection molded parts generated during the cooling stage of the injection molding cycle. the initial temperature field corresponds to the end of the filling stage. the fully time - dependent algorithm is based on the calculation of the elastic response at every time step. numerical results are discussed with respect to temperature and pressure

    文摘:不均勻的熱殘余應力及其變形是注塑成型加工中常見的工程問題之一.應用熱流變簡單材料的二維熱粘彈本構方程得到的遞推公式，數值模擬了成型中的熱殘余應力及其翹曲變形，並用數值實驗討論了溫度、壓力對注塑件殘余應力及變形的影響，發現溫度變化不均勻是注塑件翹曲變形的最主要原因，其影響遠大於壓力的作用，與工程實驗的結論一致
  7. In the numerical methods section, a finite element / control volume mold filling simulation, a tensor representation of fibre orientation and a finite element solution of the transient fibre orientation equations are combined in the program. the input data and output results are visualized by means of finite element software

    程序中用有限單元控制體方法模擬模壓流動，用表徵纖維取向的張量和有限元伽遼金方法來解決瞬時纖維取向方程，用計算機圖形原理編程實現對smc流動軌跡、纖維取向分佈的計算機模擬。
  8. According to the experiment of influences of fiber structures and the width of edge channel on flow filling, it was found that even a small gap ( l or 2mm ) between the preform and the mold edge could also disrupt the flow pattern, which evidently changed the local permeability of preform. the filling process was simulated using the permeability for different edge width predicted by a. hammami or poiseuille model, which shown good agreement with the experiment results

    實驗研究了纖維鋪層結構及流道縫隙的寬度對充模流動的影響，發現在纖維預成型體和模具壁間存在的較小的縫隙也會對邊緣的流動產生干擾，進而影響增強材料主體的滲透；對于不同的縫隙寬度，分別根據a . hammami模型和poiseuille模型預測邊緣等效滲透率，並進行充模過程數值模擬，與實驗結果吻合較好。
  9. First, according to the demand of vimp for resin system, the reaction kinetics and rheological of up resin are investigated and the optimal content of low additive profile ( lpa ) is determined. then vimp based on a high - permeable medium and grooves are studied by visual experiments, through which the appropriate high - permeable mediums are selected and the parameters of width, depth and spacing for flow grooves and spacing for supply grooves are optimized. furthermore, various factors affecting the mold filling process are discussed and the whole vacuum infusion procedures are described taking examples of the manufacture of a model boat and a sandwich panel in one infusion

    文中首先根據vimp對樹脂體系的要求，對vimp用不飽和聚酯樹脂體系的動力學和流變學性能進行了研究，確定了最佳低收縮添加劑的含量；對高滲透介質型和溝槽型vimp開展了實驗研究，通過可視化實驗優選出較好的高滲透介質，確定了引流槽的寬度、深度和槽間距及主槽的槽間距等工藝參數並進行了優化；對影響充模過程的各種因素進行了詳細的討論，並以模型船和夾芯面板的製作為實例描述了兩種vimp的成型過程；在實驗的基礎上，建立了二維滲漏模型，採用控制體有限元法對高滲透介質型vimp進行了成型過程的計算機模擬計算，通過充模時間和流動前峰的計算值與實驗結果的比較，驗證本文所採用的數學模型和數值方法的正確性，其結果對實際生產具有一定的理論指導意義。
  10. Sbs injection is generally in medium speed, but sebs injection must be in higher speed, to prevent the freeze - off of melting plastics when filling up the mold

    注射sbs材料通常使用中等的注射速度.但注射sebs材料就必須使用較高的注射速度，以避免熔膠在填模時半途「凍結」 freeze - off
  11. The mould filling process of rheo - diecasting of semi - solid magnesium alloy and die casting of liquid magnesium alloy has been simulated with the computer program of mold filling process

    摘要利用數值模擬技術，模擬了鎂合金液態壓鑄和半固態流變壓鑄成形充型流動過程。
  12. A new implicit numerical algorithm was proposed for mold filling simulation of rtm

    摘要rtm充模分析的隱式方法需要迭代來決定樹脂注滿的區域。
  13. Reserve some slices for placing on top of the nutella filling which will be the bottom of the cake when removed from the mold

    記得預留出一些蓋到慕斯餡上面，出模后翻過來時便成了蛋糕底了。
  14. Based on filling / post filling simulation in injection molding and design of experiment ( doe ) technology, the fractional factorial design method was introduced to investigate the significance of interaction among process parameters, and each factor ' s effect on the quality of mold part was also studied

    摘要基於注射成型充填后充填數值模擬，結合實驗設計（ doe ）技術，應用分析因實驗設計方法，研究工藝參數之間存在的兩兩交互作用，以及工藝參數對製品質量的影響度。
  15. Edge effect in the mold filling of lcm

    充模過程中的邊緣效應
分享友人
分享到 Line

分享到臉書