fin pitch 中文意思是什麼
fin pitch
解釋
散熱片距-
Numerical analysis and experimental study on performance of evaporator with combination of different fin pitch
變片距蒸發器性能數值分析與實驗研究 -
The experimental results of air heat transfer show that the relative fin height, relative fin width, relative fin pitch and density of 3 - d ift with staggered arrangement fins all have an effect on heat transfer and flow friction. especially, the effect of fin density is bigger
空氣換熱實驗的結果表明：肋叉排三維內肋管的相對肋高、相對肋寬、相對肋間距以及肋密度均對其對流換熱特性有影響，其中肋密度的影響較大。 -
According to purpose of the towed flight, a new trajectory consisting of taking off, climbing phase, level flight phase is presented with. trajectory pitch angle of the towing plane is optimized. according to the flight law of the towing plane, the fin deflection angle and amplification coefficient of particle - system trajectory of carrier rocket are designed, in order to realizing flight steadily of the carrier rocker
根據牽引飛行的目的，對載機應用了「起飛?爬升?平飛」的變軌道飛行方案，同時對載機軌道的傾角、傾角變化規律進行優選設計；再根據載機的飛行規律，對運載器質點系軌道的舵偏規律及其放大系數進行了設計計算，實現運載器穩定牽引飛行。 -
Diesel engine, main turbine, generator turbine, main boiler, diesel generators, deck crane, deck machineries, propeller, controllable pitch propeller, switchboard, engine control console, fire extinguishing system, inert gas system, aux. boiler, oil purifier, navigation equipment, life boat, anti rolling system, hatch cover, compressor, fin stabilizers, valves, anchor, chain and scaffolding, control system for lng carrier and various machinery for lng carrier
主機柴油機，液化氣船主機透平鍋爐貨油泵，機艙泵，發電機，甲板吊機，甲板機械，螺施槳， cpp ，配電盤，主機遙控，消防沒備， igs ，輔鍋爐，分油機，航海儀器，救身艇，減搖裝置，艙口蓋，空壓機，減搖鰭，閥門，錨，錨鏈，船舶腳手架，液化氣船控制系統，液化氣船用各種沒備 -
Various successive partial plastic forming methods for processing groove, including thread rolling, cross rolling and skew rolling, splitting, rolling of spline shaft, split rolling, open - die extrusion of spline shaft / gear, extrusion of internal screwed tooth socket parts with large helical pitch, integral cold forging for slot commutator, extrusion - ploughing for outside fin tube, drawing of tube with spiral internal / external ribs etc. have been introduced briefly
摘要介紹了用於加工槽的各種連續局部塑性成形方法，包括螺紋軋制、橫軋與斜軋、分劈、花鍵軸滾軋、劈分軋制、花鍵軸齒輪開模擠壓、花鍵套擠壓、槽型換向器整體冷鍛、外翅片管擠壓一犁削、內外螺紋管拉拔等。 -
3. the combined trajectory control system is designed. the direct force is acting on the pitch channel and the yaw channel, and the roll channel is stabilized by the fin surface deflection
設計的軌控直接力作用於俯仰和偏航通道，而滾轉通道沒有直接力系統的作用，依靠氣動舵面的偏轉對滾轉角進行穩定。
分享友人