final amplifier 中文意思是什麼
final amplifier
解釋
了未級放大器-
Actuation of one clutch provides positive torque to the final drive, the capstan acting as the main power amplifier.
一個離合器的作用是給最後一級傳動機構，即作為主功率放大器的絞盤，提供正向力矩。 -
Purpose : transceiver final amplifier application, hf transceiver application
用途:用於無線收發機的末級放大和高頻收發。 -
Theoretically several solutions are derived in the final scheme such as broadband matching technology which included negative - feedback technology, traveling wave technology and balance technology. in addition, the design will be optimized by eda software and the final test result indicates that our design is successful. the principle of microwave amplifier is introduced at first in this paper, especially its main parameters index sign, then the material performance and the influence of parasic parameter and model setting of the gaas phemt is discussed
文中首先介紹寬頻帶放大器的主要參數指標，接著介紹了gaasfet的材料特性，以及phemt管芯寄生參數對實際放大器設計的影響，然後討論gaasphemt的大、小信號模型的建立與分類;結合gaasphemt模型和s埠參數分析了寬頻帶匹配技術的原理;最後論述本課題中各個放大器實現的具體方案，以及在放大器實現過程中應該注意的問題，給出了實際寬帶放大器的測試結果，並將軟體模擬結果與實測曲線進行對比。 -
At present the manufacture of surface acoustic wave use the technology of the final submicron. a series of the devices of low insertion loss, high q saw rayleigh surface acoustic wave resonators or stws that insertion loss has less than 5db, load quality factor ( ql ) is more than 1000 on the quartz piezoelectric with zero of first temperature factor in the research. these difference frequencies are 60mhz, 280mhz, 739mhz and 1ghz of normal frequency and at also surface acoustic wave. using 1. 25db noise factor amplifier, careful design curcuit, good setting printed curcuit board, and using the 1ghz surface transverse wave resonator as frequency element, researching the low phase noise surface acoustic wave with sideband phase noise near ? 120dbc / hz deviating 1khz on carrier, spurious suppress with 80db
本研究採用一階溫度系數為零的壓電石英基片上製作出損耗小於5db 、有載品值因素（ ql值）超過1000的一系列低損耗、高q值聲表面波rayleigh波或stw諧振器，頻率分別為60mhz 、 280mhz 、 739mhz和1ghz等不同頻率的高性能聲表面波諧振器。並採用噪聲系數為1 . 25db的低噪聲系數放大器，精心設計電路，優化設計布置印製電路板，用標稱頻率為1ghz的聲表面波諧振器為頻率控制元件，製作出在偏離載頻1khz處的單邊帶相位噪聲近- 120dbc / hz 、雜波抑制達80db以上的低相位噪聲聲表面波振蕩器。 -
This subject aim at designing a linear power amplifer whose output power is 40w for 225 - 450mhz band. but it seems not easy to finish the task because of this power amplifier own unique requirements including high output power, broad working frequency band, high linearity, and flat gain. due to the complexity involved, theoretically several soltuions are derived in the final scheme such as broadband matching technology, power - retreat, power synthesize, automatic power control and negative feedback. in addition, the design will be optimized by eda software and the final test result indicates that our design is successful
本課題的目標是研製一個輸出功率為40w的225 450mhz的線性功率放大器。由於該功放要求輸出功率大，工作頻帶寬，帶內增益波動小，線性度高，所以其終合設計難度大。鑒于這個原因，在理論設計上筆者採用了寬帶匹配、功率合成、功率回退、負反饋、自動功率控制等技術；在實踐中精心設計電路，並且配合eda軟體模擬，最終達到所要求的指標。 -
Firstly, the theory and the architecture of hardware system are described, secondly, the steps of the signal processing are discussed in detail. based on the experiments and the characteristics of the signal, we pre - process the signals with band - pass filter, proportional amplifier and coherent demodulator. after sampling and analysis doppler information, we display the final results distinctly to alarm in time
然後，結合系統中各主要部分的任務，詳細介紹了信號處理的各個步驟：通過實驗比較，並結合接收信號的特點，選用帶通濾波器、比例放大器、相干檢波等技術對信號進行預處理；然後對獲得的多卜勒信息進行采樣和頻譜分析；最後，用比較直觀的形式顯示數據結果，以及時準確地告警。 -
That did not use double slope integral amplifier to realize equivalent sampling. in the course of testing the use of two methods designed to achieve equivalent sampling, the final selection of one of the best ways to be able to meet the demand of users results and performance indicators
該方案的優點是運用了大規模可編程邏輯器件fpga來實現隨機等效采樣而不是採用典型的基於雙斜率電容充放電的電路來實現的。在設計過程中試驗用兩種方法來實現等效采樣，最後選用了一種最好的方法，得到的結果能夠滿足用戶的要求和性能指標 -
In order to make full behavior simulation of sigma - delta modulator, the noise models have been set, taking into account most of the sigma - delta modulator ’ s non - idealities and the final result supports the noise models. last, the main circuits of modulator have been designed, such as operational amplifier, comparator and clock generator, the design principle of noise - killed logic circuit has been presented. these circuits have been simulated
調制器的噪聲模型，考慮了影響調制器性能的一些主要非理想因素，通過模擬驗證了噪聲模型的正確性;最後，設計實現了結構中的主要電路，如運放、比較器、時鐘產生電路，闡述了噪聲抵消邏輯電路的工作原理，利用hspice和cadencespectre對各電路進行了模擬，驗證其功能。
分享友人