finger joint 中文意思是什麼

finger joint 解釋
指接
  • finger : n 1 指頭，手指〈一般指拇指以外的手指〉。2 指狀物；（手套的）指部；（鐘表的）指針。3 一指之闊〈約3...
  • joint : n 1 接合，榫接合處，接合點。2 【解剖學】關節。3 【植物；植物學】節。4 【電學】接頭。5 【建築】接...
  1. The paper briefly describes the structure of the electrical system in the finger of a new dextrous hand, introduces driving system based on fpga in the base joint of the finger

    簡要描述了靈巧手手指電氣系統的結構，詳細介紹了基關節基於fpga的電機驅動電路。
  2. Single blade carbid finger joint cutt for woodworking

    木工硬質合金單片指接銑刀
  3. The blow is struck with the side of the hand, all the force being concentrated in one small area, approximately half way between the base of the little finger and the wrist joint

    該技術以手掌外側進行打擊，全部力量集中在一個狹小區域，約在小指根部到腕關節的正中間。
  4. The company is producing and exporting china fir and pine relatied production such as fencing, finger - joint panel, blockboard, plywood ect. mainly in charge of export business

    這家公司主要生產杉木製品，如柵欄，指接板，細木工板，杉木膠合板等. 。主要負責以上產品出口。
  5. Sell finger joint board - edge g.

    建議使用800x600解析度，聯系郵件：
  6. Among them, operating with the power from the tip of the thumb is called finger - tip pushing ; in which the interphalangeal joint of the thumb is fixed at the back - stretching position, operating with the force from the whorled surface is shao - shang point at the side of the thumb - radius is called lateral pushing, in this operation, the operator slightly flexes his wrist joint with index finger, middle finfer, ring finger and little finger naturally stretching forward in the finger - separating pattern

    以拇指端峰為著力點操作的稱指峰推；操作時，拇指之間關節固定在背伸位，以羅紋面為著力點的稱羅紋推；以拇指橈側少商處為著力面的又叫偏峰推，此法操作時腕關節略屈，食、中、無名、小指向前自然伸開，成散手狀。
  7. This manipulation is operated by the tip of the middle finger or the joint of the index and middle finger, pounding at the certain points or part regularly

    用中指指端或食指、中指屈曲后的近側指間關節突起部為著力點，在一定的穴位或部位上做有節律地點擊，稱為「搗法」 。
  8. Objective to report the result of the defects of metacarpophalangeal joint from 2 to 5 repaired by metacarpal articular surface with dorsal metacarpal artery and using kirschner pins to transfix the injured finger and the nearby normal finger

    目的報道利用傷指鄰近的正常手指作為生理性外固定支架與傷指並指固定，應用帶血供的掌骨近端骨塊修復2 - 5掌指關節缺損的效果。
  9. Then, the forward and inverse kinematics of multifingered hands in joint space and the redundancy problem of the single finger are analyzed, which are followed by correlative simulation tests

    然後對其運動學的正、逆問題進行了分析和模擬，並對單手指的冗餘問題進行了討論。
  10. A case study is presented for the reachable workspace of the human finger ( flexion / extension planar motion ), based on the research on the anthropometric data of human finger kinematic parameters and the joint motion range limits, and then 3 - d modeling of fingers reachable workspace using a recursive swept boundary method is constructed

    通過測量活體手指的長度及活動度，研究了人體手指幾何和運動參數的分佈，並用曲麵包絡的方法求出手指可達工作空間的三維模型。
  11. We hereby report a 20 - year - old male sustained an old trauma with stiff pip joint of his right little finger

    我們藉此報告一位20歲男性因為右小指陳舊性外傷而造成他的近端指間關節炎合併完全強直。
  12. Abstract : this paper puts forword and verifies the ratio of the length from one finger point to the other shoulder joint to that between finger points of two hands when one raises one " s two arms levelly obeying normal law of eu 0. 168

    文摘:提出並檢驗了雙臂側平舉時人體從一支手尖到另一個肩關節的長度與兩支手的手尖之間的長度之比依正態分佈期望為0 . 618
  13. Standard specification for elastomeric flexible hinge finger total joint implants

    彈性撓性全指關節植入物的標準規范
分享友人
分享到 Line

分享到臉書