fitting procedure 中文意思是什麼

fitting procedure 解釋
擬合程序
  • fitting : n 1 配合，裝配，裝修。2 （衣樣的）試穿。3 〈 pl 〉【機械工程】用具；零件，附件，（接頭）配件。4 ...
  • procedure : n. 1. 工序，過程，步驟。2. 程序，手續；方法；訴訟程序；（議會的）議事程序。3. 行為，行動，傳統的做法；（外交、軍隊等的）禮儀，禮節。4. 〈罕用語〉進行。
  1. The laser radar sub - system determines the heights of the tsp according to the slant height and the oblique angle measured by the laser range finder and the electronic theodolite simultaneously. by lucubrating the motion law of tsp, we decided to compute decent velocities with least - squares procedure & two ranks curve fitting

    地面激光雷達跟蹤測量分系統根據測量到的斜距離和俯仰角確定末敏彈傘彈系統的高度，在深入研究末敏彈穩態掃描過程的運動規律后，通過最小二乘法的二階分段曲線擬合，計算出落速。
  2. The second aspect is the study and application of fitting method after introducing curve fitting method, we will study least - squares procedure used frequently in engineering fields. in addition, we will encode according to item requirement and least - squares procedure algorithm, then using the data picked from image processing to fit the equation we needed

    在介紹了曲線擬合方法之後，主要研究工程設計中常用的最小二乘法，根據課題要求以及最小二乘法的演算法要求編寫源碼，將圖像處理后採集來的數據擬合成所需要的方程。
  3. 3. according to the experimental results and the method to design road surface by using cement concrete, design theory, design method and design procedure fitting for single - skin and compound fiber - reinforced concrete road are brought forward. 4

    根據試驗結論，並依據水泥混凝土路面設計方法，得出了適合於單層式鋼纖維混凝土和復合式鋼纖維混凝土路面的設計理論、設計方法和步驟。
  4. A global crack - line displacement fitting procedure ( gcdfp ) for computing stress intensity factors ( sif ) has been developed. the precision of sif is compatible with the corresponding cod data

    使用paris公式求出裂紋前緣各點的裂紋擴展增量，並用三次b -樣條函數對這些增量進行擬合，得到新的光滑裂紋前緣。
  5. And in allusion to the shortcomings on the fitting of noises by least square, a new procedure is presented to modify the estimations of model parameter of the noise. it can control the effects of the correlation noise of except for first order self - correlation noise. using the model the error of gps / ins integrated navigation system is estimated

    再次，針對卡爾曼濾波方程的前提條件不滿足而影響導航系統的精度的問題，應用時間序列分析理論提出了一種改進的噪聲模型參數估計演算法，對此演算法進行建模，模擬結果表明，該演算法能有效的控制一階自相關特性以外的噪聲對參數模型估計的影響，提高卡爾曼濾波精度。
  6. The molding procedure includes dealing with the end points of section curves, fitting the curves with the defining points, smoothing the curves, sheet molding of the blade surfaces and solid molding of the blade body

    造型過程如下：葉身截面線的端點處理、葉身截面線的擬合處理、葉身截面線的光順處理、葉身曲面造型、葉身實體生成。
  7. Besides providing the surface of the scene, the fitting procedure helps to filter out some large reconstruction errors

    擬合過程在給出場景表面的同時，可以去除一些誤差較大的重建結果。
  8. It changes traditional production working procedure, and labor efficiency gets improvement and reduces labor operation intensity. equipment volume is small, and made candy surface is smooth and with fitting transparence is high and accords with food sanitary demand

    它改變了傳統的生產工序，勞動效率得到了提高，降低了勞動操作強度。設備佔地面積小，澆注成型的糖果表面光滑，夾心透明度高，符合食品衛生要求。
  9. The estimation procedure is based on the steady - state characteristics versus slip curves. the sum of squares of differences between calculated and experimental characteristics is employed as the fitting criterion. the machine parameters are obtained by minimizing the least - squares cost function using genetic algorithms

    該方法利用電機穩態特性曲線，以特性計算值和實驗值的擬合誤差的平方和作為判斷準則，通過應用遺傳演算法最小化二乘準則函數來獲取電機參數。
  10. The parametrization work of eck et al., and the b - spline construction scheme of peters. the main contribution of this procedure are : it presents a combinatorial optimization method for builing a quadrilateral domain from a triangular one ; it presents an efficient method for fitting a gl b - spline surface of arbitrary topological type to unorganized points ; it introduces a scheme for adaptive refinement of the quadrilateral patch network

    論文工作利用了以前hoppe的表面重構工作， eck的參數化工作和peters的b樣條重構方案，主要貢獻在於：提出了從三角形域構造四邊形域的組合優化方法；提出了從無序點重構具有任意拓撲結構g1連續nurbs曲面的有效方法；提出了四邊形網格自適應細分的方案。
  11. Finally, in allusion to the shortcomings on the fitting of colored noises by least square, a new procedure is presented to modify the estimations of model parameter of the colored noises. it can control the effects of the correlation noise of exept for first order self - correlation noise

    最後，針對有色噪聲最小二乘擬合在動態gps有色噪聲模型參數估計中存在的問題，應用時間序列分析理論提出了一種有色噪聲模型參數的改進演算法，有效地控制了一階自相關特性以外的相關噪聲對模型參數估值的影響。
分享友人
分享到 Line

分享到臉書