flash pressure 中文意思是什麼
flash pressure
解釋
擴容壓力-
Hydraulic driving system performance is stable, its control and adjusting is convenient and it is safe and reliable. using the synchronous display of the curve of oil pressure and wheel speed and the flash of the control principle. it implements the real synchronous depict of abs word process and control result
液壓驅動系統性能穩定、控制調整方便、工作安全可靠，利用油壓與輪速曲線及控制原理動畫的同步顯示，實現了對abs系統工作過程及控制結果的真實、實時描繪。 -
Some of problems in distillation technology process are studied using excel, matlab and chemcad. they are distillation with simple balance, determining accurately the position of sensitive plates in distillation tower, distillation of multi - components, and crude distillation at steady state. this paper shows how to solve bubble & dew points for binary ideal system and five cases of flash by means of excel and analizes reducing pressure affects on phase equilibrium as an example of distillation and separation ethyl benzene & phenyl ethylene below atmosphere
基於excel 、 matlab和chemcad軟體，對蒸餾過程中的簡單平衡蒸餾、精餾塔靈敏板位置確定方法、多組分精餾等進行了數值計算與定量研究，對原油煉制常減壓塔進行了初步的穩態模擬，實現了用excel求解雙組分理想體系的泡、露點問題和閃蒸計算的五種情況，並分析了減壓對其相平衡的影響。 -
The research of this paper includes : ? high - speed photography and flash x - ray radiography are both used to capture the process of al shell ' s great deformation under low pressure. front illuminations are used to get the development of the fracture on the al shell. the relative energy release is analyzed from overpressure curves measured with some sensors
本文的研究內容主要包括： ?在受試炸藥經歷低應力大變形過程的susan試驗中，同時採用高速攝影、閃光x射線照相對彈體的撞靶過程進行了拍攝，得到了殼體膨脹變形過程圖像，並使用前照明技術觀察到了鋁殼表面產生的裂紋及其發展變化過程；從壓力傳感器測量的空氣沖擊波超壓曲線，獲得反應釋放總能。 -
Step3 inject remain 1 / 3 of product. according to product molding speed and pressure lower than that of step2 to preent flash speed and pressure should decrease but it can ' t shot short
第三段是注射餘下的1 / 3段，其速度和壓力根據產品的需要，一般是小於第二段，速度和壓力存在於一個往下降的過程.主要是為了防止產品毛邊的產生，但同時又必須把產品充填飽滿 -
Step3 inject remain 1 / 3 of product. according to product molding speed and pressure lower than that of step2 to prevent flash speed and pressure should decrease but it can ' t shot short
第三段是注射餘下的1 / 3段，其速度和壓力根據產品的需要，一般是小於第二段，速度和壓力存在於一個往下降的過程.主要是為了防止產品毛邊的產生，但同時又必須把產品充填飽滿 -
Specification for flash welding of steel tubes for pressure applications
承壓鋼管的閃光焊規范 -
Maximum pressure without flash generates optimum physical properties for your rtp company material
最大的壓力而沒有毛邊會造成使用的rtp公司材料有最適當的物理特性。 -
It is obtained by distilling soft pitch in flash column under certain pressure and temperature
中溫瀝青經過在一定的壓力和溫度下進行閃蒸獲得。 -
Injection pressure should be set low initially and increased to the point of filling the part just short of causing flash
一開始應設定低的射出壓力以填充零件至剛好不會造成毛邊。
分享友人