flat gain amplifier 中文意思是什麼

flat gain amplifier 解釋
平坦增益放大器
  • flat : n 1 〈英罕〉地板；（房屋的）一層。2 一套房間；〈pl 〉分宅公寓〈美國高級公寓叫 apartment house〉。...
  • gain : vt 1 獲得；博得，掙得；贏得，打勝（戰爭、官司）。2 吸引；爭取…（到一邊），說服。3 （尤指通過努力...
  • amplifier : n. 1. 【電學】擴大器；擴音器。2. 放大鏡；放大器。
  1. The influence of the configuration, the pump wavelength, the bragg wavelength, the reflectivity, the pump power and the length of edf to the gain - clamped characteristics is studied. an optimal l - band gain - clamped edfa configuration with appropriate parameters of the amplifier, which can also provide a flat - gain band, are given

    總之，本論文圍繞光纖通信領域的國際熱點問題，從理論和實驗上研究了高增益、低噪聲、譜平坦的摻餌光纖放大器的實現，關于edfa的特性的研究成果，我們相信能對科研生產起一定的指導作用。
  2. Raman fiber amplifier （ rfa ） is a kind of optical amplifier that can amplify signal light directly through nonlinear interaction of high intensity pump and signal light in fiber. whereas the spectrum of raman gain coefficient of optical fiber is not flat, the gain of signal light with different wavelength induced by a single pump is rather different, when wavelength division multiplexing ( wdm ) signal light is amplified by a single pump, the gain spectrum of the wdm signal light is not flat. the flatness of the wdm signal light has important impact on the optical signal - to - noise ratio ( osnr )

    拉曼光纖放大器（ ramanfiberamplifier ，簡稱rfa ）利用高強度的泵浦光與信號光在光纖中的非線性相互作用實現信號光的直接放大，但是由於光纖的拉曼增益系數譜很不平坦，所以同一泵浦光源對不同波長信號光的增益就存在很大的差別，因此，用單泵浦光源來放大波分復用（ wavelengthdivisionmulti - plexing ，簡稱wdm ）信號光時，各信號光的增益值就有很大差異， wdm信號增益的平坦度對光信噪比（ opticalsignal - noiseratio ，簡稱osnr ）有重要影響。
  3. This subject aim at designing a linear power amplifer whose output power is 40w for 225 - 450mhz band. but it seems not easy to finish the task because of this power amplifier own unique requirements including high output power, broad working frequency band, high linearity, and flat gain. due to the complexity involved, theoretically several soltuions are derived in the final scheme such as broadband matching technology, power - retreat, power synthesize, automatic power control and negative feedback. in addition, the design will be optimized by eda software and the final test result indicates that our design is successful

    本課題的目標是研製一個輸出功率為40w的225 450mhz的線性功率放大器。由於該功放要求輸出功率大，工作頻帶寬，帶內增益波動小，線性度高，所以其終合設計難度大。鑒于這個原因，在理論設計上筆者採用了寬帶匹配、功率合成、功率回退、負反饋、自動功率控制等技術；在實踐中精心設計電路，並且配合eda軟體模擬，最終達到所要求的指標。
分享友人
分享到 Line

分享到臉書