flat valve 中文意思是什麼

flat valve 解釋
蓋閥
  • flat : n 1 〈英罕〉地板；（房屋的）一層。2 一套房間；〈pl 〉分宅公寓〈美國高級公寓叫 apartment house〉。...
  • valve : n 1 【機械工程】閥，活門，舌門；汽門。2 【解剖學；動物學】瓣，瓣膜；（貝）殼瓣；【植物；植物學】...
  1. The mattress should be stored flat and with the valve open until it is to be packed for a trip

    氣墊儲存的時候要放平，閥門打開，知道充氣完畢。
  2. This paper has built more precision mathematical model for the valve controlled asymmetrical cylinder system based on the simulink simulation flat, then according to actual need and combining self - adaptive control theory, we choose a mathematic model which has good performance to be the reference model of our adaptive control and adopt velocity system of asymmetric cylinder controlled by symmetric valve as controlled device to design the adaptive controller

    本文建立了基於simulink模擬平臺上的閥控非對稱缸系統較精確的非線性模型，然後根據對系統提出的性能指標要求，結合自適應理論選取性能良好的數學模型作為自適應控制的參考模型。以閥控非對稱缸速度系統作為被控對象，設計自適應控制系統。
  3. Since the compensation valve cannot open unless it is mechanically actuated by the flat diaphragm via a lever, it ensures that the flat diaphragm and the hose diaphragm cannot be over - stretched

    除非通過杠桿受平隔膜的機械作用，補償閥門是打不開的，這就保證了平隔膜和軟管隔膜不會被過分地拉伸。
  4. Using the system developed, we have set up the basic drawing - base of four different valves such as resilient seated gate valve, the wedge flat gate valve and the three - eccentricity butterfly valve etc. so these four type valves can be rapidly designed. it is shown that this system realizes the valve quickly modeling, consumedly increases the valve design efficiency, and has stronger extensibility

    應用已建立起的閥門三維參數化設計系統開發了「軟密封膠板閘閥」 、 「撐開式平板閘閥」 、 「三偏心蝶閥」等四種結構的閥門基本圖形庫，可對這四種結構的閥門進行快速序列化設計，大大提高了閥門設計生產效率，並具有較強的可擴充性。
  5. Mainly directing against leaking of pz900 high temperature flat valve body with hydraulic pressure, utilizing foundry technology theory and metal solidification principle, combineing computer aided design, analyzed casting process and found out the defect causation, the leaking defect resolved

    摘要主要針對pz900高溫平板閘閥閥體試壓滲漏的問題，利用鑄造工藝理論和金屬凝固原理，結合計算機輔助設計，對閥體的鑄造工藝進行了分析，找到了產生缺陷的根本原因，解決了該件的滲漏問題。
  6. Aiming at several representative electric - hydraulic control module of the construction machine control system based on the can bus will stand out all the electric - hydraulic control system of the construction machine. based on what we have said above, we design the communication adapter, data acquisition module, data control module and the hydraulic test flat which is controlled by the high - speed switch valve

    針對工程機械幾種典型的電液控制模塊，分析其功能需求，並探討了其實現的控制方式、控制復雜程度和數據傳輸和處理的量，經過縱橫向比選后，認為基於can - bus的數字電液控制系統必將成為下一代工程機械電液控制的主流。
  7. Delivery valve installation - part 6 : dimensions of cabinets and installation of hose reels with lay - flat hoses according to din en 671 - 2

    消防水龍帶閥門裝置.第6部分:扁形消防水龍帶壁裝消防
  8. Flat slide shut - off valve

    平板式截止閥
  9. Seat end of valve must be mated to a standard flat faced metal flange. rubber flanges not acceptable

    閥門的閥座埠必須與平面金屬法蘭配合。橡膠法蘭是不可接受的。
分享友人
分享到 Line

分享到臉書