fluidity temperature 中文意思是什麼

fluidity temperature 解釋
液流性溫度
  • fluidity : n. 流動性，流度；流質；液流度，液性。
  • temperature : n. 1. 溫度，氣溫。2. 體溫。3. 〈口語〉發燒，高燒。
  1. Ptfe is one of the most corrosion - resistant materials in the world. however it has defects such as the hot expansion and cold contraction rate is10 times larger than that of steel and the original cold fluidity ( creeping ) etc. therefore, as temperature increases, ptfe extends so excessively that it would collapse and then block the flow of media ; as temperature decreases, ptfe contracts so excessively that it would be ripped and then cause leakage

    Ptfe是當今最耐腐蝕的材料之一，可它被製造成襯里的時候，會存在熱脹冷縮比鋼鐵十多倍及固有的冷流性等缺陷，致使ptfe襯里管道、設備，在使用過程中，溫度高時， ptfe襯里層會伸長過多而內癟，阻塞了介質流通；溫度低時， ptfe層會收縮過大被拉裂而泄漏。
  2. The solution had good fluidity, spinnability, dynamic stability, and would never be demixing. the original camp fibers had better water absorbability when the spinning temperature was 80 and pressure was 0. 4mpa

    紡絲溫度為80 ，紡絲壓力為0 . 4mpa時，以丙酮為凝固劑，經濕法紡絲成形后，得到的camp初生纖維具有較好的吸水性能。
  3. According to the production practice to produced - 35 ( superscript # ) diesel fuels with added low temperature fluidity improver through the years, the effect of the different low freezing diesel composition on susceptibility of low temperature fluidity improver are described, and their mechanism is discussed

    摘要根據多年來採用加入低溫流動性改進劑生產- 35號低凝柴油的生產實踐，闡述了不同的柴油組分對柴油低溫流動性改進劑感受性的影響，並對其原理進行了探討。
  4. Our research is to design the mould arid optimize the molding parameters such as temperature and pressure and finally make the fender to meet the design requirements. also the fluidity and thermal conductivity of gmt are studied and theoretically analyzed the fluidity of gmt is studied by compressing the round shape gmt sheet under constant temperature

    本課題研究的主要目的是制定模具設計方案，優化成型工藝參數（溫度、壓力制度等） ，研製出滿足國產悍馬軍車擋泥板設計要求的製品；同時結合產品的研製，對gmt材料的流動性能、熱傳導性能進行初步的探索，為gmt製品的工業生產提供指導。
  5. Remarkably, the temperature must be limited between softening point and solidification value, at which the bond can get perfect fluidity and stickiness. effects of bond content and pressure on magnet product during heating - pressing process are the same with effects during common - pressing process. fourthly, it is more than 250 hours before magnet is eroded when it is coated with lacquer by way of cathode electrophoresis

    溫度對溫壓效果影響明顯，應當選擇在粘結劑軟化點以上、固化反應前的某一點，保證粘結劑具有適當的粘度和良好的流動性；與普通壓制工藝相同，溫壓工藝制備的粘結磁體密度和磁性能均隨壓制壓力的增大而提高，磁體性能和磁粉體積分數隨粘結劑含量變化的規律一致。
  6. In addition, jewelry alloys used in wax setting and casting must have the properties of low melting temperature, good fluidity and anti oxidization properties

    用於蠟鑲鑄造的合金應具有較低的熔點、較好的流動性及抗氧化性能等。
  7. First, by measure the fiber content in different radius range, the influence of pressure and temperature on fluidity is investigated

    1 ）通過測量擠壓流動后不同半徑范圍內的纖維含量，研究了壓力、溫度等對材料流動性能的影響。
  8. Standard test method for determination of low temperature fluidity and appearance of hydraulic fluids

    測定液壓液低溫流動性和表面特性的標準試驗方法
分享友人
分享到 Line

分享到臉書