form coating 中文意思是什麼
form coating
解釋
模板塗料-
This product is the newest filming technique, the latest achievement of usa electronic magic, it utilizes decomposition principle of electronic material to form a positive negative ions film on the surface of car coating, which has high water repellency and makes the surface of coat has more than 95 % brightness of mirror surface, lt has preeminent performance on weathering resistance, ageing resistance, oxidation resistance static resistance and wear resistance, with the force of charged ions, this product can easy removes the dirt, water drop acid rain and grease on the surface of the film and perennially and effectively protect coat surface, lt is the fourth generation car beauty and protective product which replaces glaze sealing products
本品屬于當今最新的鍍膜技術，屬美國電子工學魔法的最新成果，它利用電子物質的分解原理，在車漆表面生成持有高撥水性的正負離子覆膜，使漆面光亮度可達鏡面光澤的95 %以上，並具有超強的耐候性、抗老化、防氧化、防靜電、耐磨性極好的功能，它利用電離子的力量，可輕松彈去覆膜表面的污垢、水滴、酸雨、油脂等，平時只需清水沖洗，便可立即使之恢復離子效應，達到長期保護漆面的目的，是取代封釉的第四代汽車美容保護產品。 -
It is indicated after laser remelting, the density of the nano material infiltrated coating is improved and grain size is decreased greatly. in above researches, it is found that the nano material is distributed among general material grains to form inter - granular structure of the coating
研究發現，在各種塗層中納米顆粒明顯填充在粗顆粒間，構成晶間型組織結構；初步測試還表明，在al _ 2o _ 3 + 13 wt -
It is found that the nano material is distributed not only among general material grains to form inter - granular structure of the coating but also in the general material grains to form intra - granular structure. micro - crack caused by laser will be eliminated greatly. 3 mechanical performances of the ceramic coating manufactured are tested
得到的結論是經過激光熔覆后的塗層緻密化程度有了很大的提高，比單純的激光重熔塗層還高，納米顆粒不僅填充在晶粒之間，而且還嵌入在大晶粒內部，有利於消除激光作用產生的微裂紋。 -
The latter can form a coating that is resilient.
后一種可形成一種有回彈力的塗層。 -
Coating machine ( whether two - sided gyro wheel scribble, is it scribble two, flatten to blow the form and two, two hot to dissolve and react the trough the polishing form ) surface processing and manufacturing is antibiotic, defends, waterproof, ventilative to used in not weaving cotton cloth, pack and prevent germs to infect and isolate and use the cloth in food, medical treatment
塗布機（雙面滾輪塗、單面刮塗二次、壓平及拋光單面二次、兩座熱溶反應槽）用於不織布表面加工製造抗菌、防? 、防水、透氣，食品、醫療包裝和預防病菌傳染隔離用布。 -
The product is adopting the numerator that the united states first enter synthesize the craft, the numerator that pass science designs, make epoxy and water polyurethane the combination, form polymers has each other thing of wearing the network construction, and join the functional monomer to it make the product can polymerize in normal temperature ; make coating have excellent hardness, luster, chubbiness and attrition resistance, water resistance ， ethanol resistance ; make the water - paint with the product has epoxy and polyurethane excellent capability
該產品採用美國最先進的高分子合成工藝，通過科學的分子設計，使環氧樹脂與水性聚氨酯分散體有機地結合，形成具有互穿網路結構的高分子聚合物；並通過功能性單體的引入賦予該產品常溫自交聯功能，使漆膜具有極好的硬度、光澤、豐滿度、耐水性及耐磨性，使配置的水性漆兼具聚氨酯及環氧樹脂的優異性能。 -
The silica coated nanometer particles after containning in n2 for 2h within 600 c is the crystallization form. thus it can sufficiently work the nano effect. the surface of the composite particles has no crystal water and no absorbing water. the anti - oxidation ability increase after coating
鐵納米復合粒子為結晶態，納米粒子在6000c ，氮氣保護下，納米粒子不重新結晶，殼層二氧化硅包裹在納米鐵表面阻斷了納米粒子之間的重新原子排列。 -
Fabrication of the box beam is divided into such parts as reinforcement, formwork, concreting, prestressing, moving and storing of beam, pipe grouting under pressure, end sealing of the beam, water - proof layer on the bridge surface system, protective coating etc. the paper makes description of effective box beam construction technology and workmanship which can be adopted in other projects, such technologies as : manufacturing and fixing of reinforcement, steel reinforcement fixing baseplate, web plate and top plate respectively and lifting the steel skeleton into form, requirements of design and manufacturing and way of utilization for dismantling - erection type formwork and hydraulic formwork, optimization of concrete ratio, concrete pouring process of two ends of beam in priority over the middle, in sequence of first baseplate followed by web plate and top plate at last, concrete pouring in inclined section and in horizontal layer, concrete vibration mainly by external vibrator in assistance with internal vibrator, methods and regulation for steam curing of concrete, dual controls over stress and strain to ensure quality of prestressing workmanship, construction method of effective beam moving by heavy - weight special moving facility, some regulations and key notes about construction of grouting under pressure, beam ends sealing, water - proof layer on the bridge surface system, protective coating
箱梁製造由鋼筋工程、模板工程、混凝土工程、預應力工程、移存梁工程、孔道壓漿工程、梁體封端工程、橋面防水層和保護層工程等施工環節組成。文中介紹的採用胎具製作和綁扎鋼筋，分底腹板和頂板分別綁扎並吊裝鋼筋骨架入模；拆裝式和液壓式兩種模板的設計、製作要求和使用方法；綜合考慮、優化混凝土配合比，混凝土灌注從兩端至中間、先底板、后腹板、再頂板的施工順序和斜向分段、腹板水平分層、附著式振搗為主、插入式搗固為輔的施工工藝，蒸汽養護的方法和規定；應力應變雙控制確保預應力施工質量的施工技術；採用重物移運器有效移梁的施工方法；壓漿、封端、橋面防水層和保護層施工的一些規定和注意事項等都是對箱梁製造行之有效的施工技術和施工方法，並可為以後類似施工作借鑒。 -
Through experiment and analyzing the changes of the thickness, rigidity, tensile strength and the opening rate of the conduits caused by the different kinds of coating material, the thickness of the coating and the different braiding structures, we investigate the physical and mechanical, properties of the braided conduits. the results show : the chitosan is easy to form the film structure on the surface of the conduits increasing the conduits ' rigidity clearly ; the rigidity and opening rate of the braided structure with inserted reinforcing yarn are better than the others, this will prevent the conduits collapsing and distorting effectively in the practical uses, so we select conduits of this structure for animal experiment
在導管的物理機械性能研究方面，本課題通過塗層劑的種類（ pgla丙酮溶液和甲殼胺漿液） 、塗層劑的厚度、導管的編織結構三個方面分析它們對導管的厚度、硬挺度、拉伸強力和孔隙率等性能的影響。測試結果顯示：甲殼胺塗層易於在導管表面成膜，對導管的硬挺度有明顯提高，塗層效果較好；加筋結構神經導管在硬挺度和孔隙率方面優于其它導管，能有效防止導管在實際應用中的塌陷變形。 -
Two world of beings with form position idea uses two kind of liquid phase medium the proportion difference, causes special coating the glass float to float in the position
二色界位計利用兩種液相介質的比重差，使特殊鍍層的玻璃浮子浮在界位上。 -
In the absence of heat, i think, no oxide coating should form during rolling
在無加熱的條件下，我想，軋制過程中不會生成鱗皮吧！ -
Conclusion the more production of matrices ， the better formation of tissue - engineered cartiolage ； the constructs of chondrocytes seeded onto pga coating with pla ， lec and plys can form tissue - engineerd cartilage in animals who have inherited immunity
結論細胞支架復合物體外培養期間有基質產生，是組織工程化軟骨生成的前提條件；以卵磷脂、多聚賴氨酸及聚乳酸共同修飾的聚羥基乙酸支架與軟骨細胞復合培養后回植到有免疫力的動物體內可生成組織工程化軟骨。 -
In the thermal shock under air medium, a main damage form of 3d - c / sic was that oxidation of carbon fibers had been caused by peel - back of carborundum coating
3d - c sic復合材料在空氣介質中的熱震損傷相應大致分作三階段，主要損傷為碳化硅塗層剝落而導致的碳纖維的氧化。 -
In terms of the unstability of it, we take dopping and coating measures to restrain it. the dopping elements include cr, al, co and ni, and licoo2 is used as the coating material. through xrd ananysis, we can know only dopping al can form limno2, the product of coating licoo2 forms the main phase limn2o4 although liniv04 has high voltage as cathode materials, it is difficult to ni3 + from ni2 +, which makes it hard in the first charge
基於limno :結構的不穩定性（在充放電過程中會不可逆的轉變為類尖晶石limnzo4結構） ，對lin [ n02進行摻雜、表面包覆改性實驗研究，通過對limnoz進行摻鉻、摻鋁、摻鉆、摻鎳等元素，從xrd物相分析可以看出:只有摻入鋁能形成limnoz :用licooz進行包覆得到是以limnzo4為主相的混合物。 -
On the surface of annealed 45 steel, as the pearlite in it contains cementite phase and has high crystal boundary density, the nucleation and growth of deposits prefer to occur at the pearlite at the beginning during depositioa the coating exists in form of nano - polycrystal layers composed by gathering of nano - sized crystals
在退火態45鋼表面，由於珠光體組織中含有滲碳體相且具有比較高的晶界密度，因而在沉積初期鍍層優先在此處形核和生長；鍍層在基體表面是以納米尺度的晶粒聚集在一起形成的聚晶體形式存在的。 -
As annealing temperature is 400, the phase of fexsy is greigite ( fe3s4 ) the fexsy particles cover the porous film of tio2. the average size of fexsy particles range from 5000nm to 20nm as the concentration of the starting solution decreasing. after five times of coating - annealing process, fexsy particles form aggregate in size of 10 m
鐵硫化合物顆粒覆蓋在多孔tio _ 2基底上，顆粒尺寸隨著初始溶液濃度減小從幾個微米減小到十幾個納米，隨著塗膜厚度、退火時間增加，鐵硫化合物的形貌按顆粒狀島狀層狀變化。 -
Effect of air and its flow form on powder coating
空氣及其流動形態對粉末塗裝的影響 -
This paper describes the theory of oxide vacuum coating and the form mechanism of film. it is discussed the technique that nonmetal is conated on polymer. the barrier performance of this new material that is produce by using different deposited method and raw materials is compared
論述了非金屬真空鍍膜的蒸發理論和鍍層的形成機理，討論了非金屬鍍膜的技術方法與工藝，比較了不同蒸鍍原料與方法對材料阻隔性能的影響與效果。 -
4, the formation mechanism of the n - sic particles in the ceramic coating prepared by the nano - micrometer n - sic / al2o3 composite powder located within m - al2o3 grains is revealed : m - al2o3 would be well melted during spraying and form droplet, the n - sic particles existing on the surface of droplet, then the particle enter the droplet when it is impacted and flattened on the substrate
4 、提出了利用納米一微米n - sic al _ 2o _ 3包覆復合粉末所制的陶瓷塗層中n - sic粒子分佈於m - al _ 2o _ 3晶內的機理：在噴塗過程中微米級al _ 2o _ 3完全熔化形成液滴， n - sic粒子存於液滴表面，在液滴撞擊基材平鋪過程中n - sic粒子進入液滴內部形成。 -
In order to prolong the lifetime of the phosphor, na2sio3 liquid phase hydrolyzation and atmospheric chemical vapor deposition of teos and o2 is adopted to form coating of silicon dioxide film on the surface of the electroluminescent phosphor zns : cu in this paper for the first time
為了延長材料的使用壽命，本論文首次採用na _ 2sio _ 3液相水解和teos與o _ 2的常壓化學氣相沉積的方法在zns ： cu發光材料的表面包覆sio _ 2膜層。
分享友人