full time circuit 中文意思是什麼
full time circuit
解釋
日夜電路-
In the hardware design, the paper completes modules ’ design like outside memory, patulous a / d, patulous d / a, rs232 communication, ecan communication, led control, keyboard control, distant control, emulation, reset, logic voltage switch, dsp supply power regulate and ac - dc power circuit, as well as room layout design like anterior panel, back panel etc. and dsp transfers data with peripheral equipments except outside memory using serial ports. besides, the whole circuit is configured in interrupt response. thus, it can meet system demand as well as take full advantage of tms320f2812 ’ s hardware resource. in the software design, the paper finishs programs like the interface programms intercommunicates with people, the distant control program, ad and da modules ’ control program, in addition, the paper select the velocity and acceleration state - feedback algorithm and is written in the program. the software design uses dsp integrate exploiting environment named ccs2. 2 of ti inc. as software instrument, and programs with the combination of c language and assembly language. moreover, in order to maintenance or modify the software expediently and shorten software ’ s exploitation time, the design adopt software modularization technique. finally, some air cylinder experiments are carried out to proved that the pneumatic controller is very practical
在硬體設計中，本文完成了片外存儲器擴展、 a / d擴展、 d / a擴展、 rs232通信介面、 ecan通信總線介面、液晶顯示控制、鍵盤控制、遠程控制、模擬、復位、邏輯電平轉換、 dsp工作電源校正電路和ac - dc電源等模塊設計以及控制器前面板、後面板等的空間布局設計。其中dsp與除外部存儲器的外圍設備之間的數據傳送全部採用串口通信，同時系統電路配置成中斷響應方式，這樣既滿足了系統要求，又充分利用了tms320f2812的硬體資源。在軟體設計中，本文完成了人機界面功能模塊、遠程控制模塊、 ad擴展模塊、 da擴展模塊、速度和加速度狀態反饋的控制演算法的程序設計。 -
These results prove that the charging action of the power supply is right. the simulation method is applied with other power supply system. at the same time, the hardware system of 2qkv - 60kw high - voltage capacitor direct current charging power supply is described in this paper, and discuss why designed a full digital phase - shifting pulse circuit
同時，本文敘述了20kv ? 60kw高壓電容直流充電電源的硬體電路的設計，其中討論了為什麼不採用已有的uc3875 、 uc3879等晶元來產生zvspwmdc dc變換器的移相脈沖，設計了全數字式移相脈沖產生電路。 -
Once any nonconforming product is found in inspections such as regular self - inspection and regular circuit inspection, the operator should perform full inspection to finished product in properly time under supervised by inspector until nonconforming product is not found
定時自檢、定時巡檢一旦發現不合格品，操作者應在檢驗員的監督下對適當時間內的已生產產品進行全檢，直到不能發現不合格品為止。 -
Three - phase full bridge controlled rectifier, filter circuit and the common loads " mathematics models are built and analyzed. according to the rate of the transition process, the controlled rectification power supply can be classified into fast response and slow response. based on identification of the transition processes using the slope method, the different fuzzy control strategy is adopted. the control method can meet the requirements of real time control and non - error regulation. the simulation results verify its practibility. after that. the design scheme based on dsp is introduced including the design of hardware and software flow chart. emc is an important aspect which can not neglected, so the designs of emc are summarized including hardware and software
根據過渡過程的快慢將可控整流電源系統分為快響應過程和慢響應過程，本文在利用響應曲線斜率法辨以過渡過程的基礎上，分別針對快響應過程和慢響應過程採取了相應的模糊控制策略，以滿足快響應過程要求實時控制，快速跟蹤誤差變化，慢響應過程要求精確定位，無差調節的要求，模擬結果驗證了該方法的有效性，進而分析了用dsp實現該調節器的硬體電路和軟體流程的設計思路。 -
In the design of real - time control system, the paper takes three - phase full - bridge mosfet inverter as the real - time control main circuit, and adopts a control scheme with 120 ? switching mode combined with half - bridge pulse width modulation ( pwm ), which would avoid straightthrough short of a certain bridge. phase current is detected by single current sensor ; three - phase position signals generated by position sensors could not only supply commutation information for inverter, but also be used for speed detecting based on signals " period measurement, which makes the speed sensor unnecessary. the whole control system adopts speed and current dual closed - loop control strategy in order to construct a high performance rare - earth permanent magnetic brushless dc motor ( repm bldcm ) full - digital real - time control system
在實時控制系統的設計中，本文以三相全橋mosfet逆變電路作為實時控制主電路，採用120導通方式結合半橋pwm調制的控制方案，從而有效地避免了橋臂的直通短路；本文用單電流傳感器實現對相電流的檢測，來自位置傳感器的三相位置信號不僅為逆變電路提供換相信息，而且也用於基於信號周期測量的轉速檢測，這樣就省去了速度傳感器；系統採用的是速度、電流雙閉環控制策略，力求構建高性能的稀土永磁無刷直流電動機全數字實時控制系統。
分享友人