full-voltage 中文意思是什麼
full-voltage
解釋
滿電壓-
Single range voltmeters are normally calibrated at cardinal points ( maximum 10 test points ). for multi - range voltmeters, the basic calibration will include measurements at full ranges and linearity check at 5 voltage levels for one range. linearity check for other ranges can be offered at extra cost
單量程電壓表一般以基點（最多十個測試點）進行校正；多量程電壓表的基本校正則會包括全量程測量及按五個電壓量位為一個量程進行線性檢查。 -
A white led driver circuit is presented in this paper. the circuit drives up to four white leds with regulated constant current for uniform intensity. by utilizing proprietary adaptive 1x / 1. 5x modes and ultra - low - dropout current regulators, it maintains the highest possible efficiency over the full 1 - cell li + battery input voltage range
整體電路以恆定電流驅動4隻白光led ，利用1倍/ 1 . 5倍分數型電荷泵和低壓差電流調節器，在整個鋰電池供電電壓范圍內保持最高的效率，並使四個白光led獲得均勻的亮度。 -
The nominal full load voltage and maximum voltage have been computed
以上已計算出額定滿負電壓和最大電壓。 -
When specifying the transformer, the nominal full load voltage is usually reduced to allow for the minus 20 % resistance tolerance of the elements and slow furnace heatup
當指定變壓器時，考慮到要減去20 %的電阻阻值，通常要減少額定滿負電壓並且使熔爐加熱緩慢。 -
A novel phase - shifted zero - voltage and zero - current switching pwm dc / dc full - bridge converter is presented in this thesis, which is based on the groundwork of summarization of the development of power electronics in recent years and lucubration in theoretical basis of modern high frequency soft switching power convert technique and analysis of operation principle, characteristic of the circuit and inherent drawbacks of the traditional phase - shifted zero - voltage switching pwm dc / dc full - bridge converter
本文在對近年來電力電子學科的發展高度綜述和對現代高頻軟開關功率變換技術理論基礎深入研究的基礎上，對傳統的移相控制zvspwmdc dc全橋變換器的工作原理、電路特性、存在的缺點進行了分析，在此基礎上提出了一種改進型的移相控制zvzcspwmdc dc全橋變換器。 -
The power ’ s quality is decided in the system performance, the amplifier has 4 groups ’ power sources, input 220v through the filter, the transformer transformation, the full - wave rectification, finally through manostat leveling off voltage, after the electric capacity filter outputs
電源質量的好壞是決定系統性能的一個重要因素，放大器共4路電源，輸入220v通過型濾波，變壓器變壓，全波整流，最後通過三端穩壓器穩壓，電容濾波后輸出。 -
A. c. high - voltage switchgear and controlgear. high - voltage motor starters. part 1 : direct - on - line full voltage a. c. starters
交流高壓開關設備和控制裝置.高壓電動機起動器.第1部分:直接在線交流起動器 -
In the hardware design, the paper completes modules ’ design like outside memory, patulous a / d, patulous d / a, rs232 communication, ecan communication, led control, keyboard control, distant control, emulation, reset, logic voltage switch, dsp supply power regulate and ac - dc power circuit, as well as room layout design like anterior panel, back panel etc. and dsp transfers data with peripheral equipments except outside memory using serial ports. besides, the whole circuit is configured in interrupt response. thus, it can meet system demand as well as take full advantage of tms320f2812 ’ s hardware resource. in the software design, the paper finishs programs like the interface programms intercommunicates with people, the distant control program, ad and da modules ’ control program, in addition, the paper select the velocity and acceleration state - feedback algorithm and is written in the program. the software design uses dsp integrate exploiting environment named ccs2. 2 of ti inc. as software instrument, and programs with the combination of c language and assembly language. moreover, in order to maintenance or modify the software expediently and shorten software ’ s exploitation time, the design adopt software modularization technique. finally, some air cylinder experiments are carried out to proved that the pneumatic controller is very practical
在硬體設計中，本文完成了片外存儲器擴展、 a / d擴展、 d / a擴展、 rs232通信介面、 ecan通信總線介面、液晶顯示控制、鍵盤控制、遠程控制、模擬、復位、邏輯電平轉換、 dsp工作電源校正電路和ac - dc電源等模塊設計以及控制器前面板、後面板等的空間布局設計。其中dsp與除外部存儲器的外圍設備之間的數據傳送全部採用串口通信，同時系統電路配置成中斷響應方式，這樣既滿足了系統要求，又充分利用了tms320f2812的硬體資源。在軟體設計中，本文完成了人機界面功能模塊、遠程控制模塊、 ad擴展模塊、 da擴展模塊、速度和加速度狀態反饋的控制演算法的程序設計。 -
Then novel circuit structure of bi - directional voltage mode ( based on forward converter ) inverters with high frequency link, are proposed, which is constituted of input cycloconverter, high frequency transformer, output cycloconverter, input and output filter ; the circuit topologies family of this bi - directional voltage mode inverters with high frequency link include six circuit topologies, such as push pull - full wave mode, push pull - full bridge mode, half bridge - full wave mode, half bridge - full bridge mode, full bridge - full wave mode, and full bridge - full bridge mode etc. taking full bridge - full bridge mode circuit as an example, principle of uni - polarity phase shifting controlled bi - directional voltage mode inverters with high frequency link is introduced
本文首先論述了dc / ac逆變技術的應用前景及發展現狀。基於正激forward變換器的雙向電壓源型高頻環節逆變器電路結構，由輸入周波變換器、高頻變壓器、輸出周波變換器、以及輸入、輸出濾波器構成;雙向電壓源高頻環節逆變器電路拓撲族，包括推挽全波式、推挽橋式、半橋全波式、半橋橋式、全橋全波式、全橋橋式六種電路。 -
The full - bridge converter was controlled with the pid strategy based on the feedback of voltage output
電源的全橋功率變換器採用基於電壓瞬時值反饋的數字pid控制。 -
The thesis includes two parties : research on 2kw multi - function ac excitation power and study on high voltage high power ( hh ) dc / dc full - bridge converter
論文包括兩個部分： 2kw多功能交流勵磁電源研製和高壓大功率dc dc全橋變換器研究。 -
This thesis focuses on the development of the dc / dc stage, which adopted the phase - shifted zero - voltage - switching ( zvs ) pwm full - bridge converter with two clamping diodes
本文主要研究單相靜止變流器的dc / dc級，它採用加箝位二極體的移相控制zvspwm全橋直流變換器。 -
After which, the battery will be charged by large constant current to allow the fast charging. finally, the constant voltage charging is adopted to guarantee the battery was charged to its full capacity. under the condition that the temperature has raised to a certain threshold at the constant current charging stage, the over temperature circuit is performing and it provides a compensation current which switches the system to constant temperature charging mode with the intention of protecting the ic
即在充電初期採用較小的電流對電池進行預處理，對出現過放電的電池進行修復和保護;然後採用較大的恆定電流對電池充電，實現快速充電的目的;最後採用恆定壓充電，確保電池充滿;在恆流充電階段，當晶元溫度上升到一定程度時，晶元過熱保護電路開始工作，該電路以提供充電補償電流的形式使充電進入恆溫充電模式，對晶元進行保護。 -
Dc voltage signal : 0 - 500v direct input ; if the voltage exceed 500v it can adopt voltage dropping device to transform into voltage signal whose full range is 100v to input
直流電壓信號： 0500v直接輸入，超過500v可採用降壓裝置轉換成滿量程為100v的電壓信號輸入 -
Phase - shifted zero - voltage - switching pwm full bridge converter can realize zvs for the power switches with the use of the leakage inductance of the transformer and the intrinsic capacitors of the power switches, so it is used widely for medium and high power applications
移相控制零電壓開關pwm全橋變換器利用變壓器的漏感和開關管的結電容可以實現開關管的零電壓開關，在中大功率的場合應用廣泛。 -
( 5 ) taking full of advantage of the ado. net and asp. net technology under the. net platform. it construct a powerful remote control and monitor system and meet the reqirment of the users. in order to achieve real - time control, it design a front environments built on the asp. net structure, from which the system can fulfill the real - time function. due to the characteristic of drain off water pump station remote control and monitor system ( big pump station need high voltage ( 6000v ) and great power ), so now do n ' t adopt the ways that client _ end controls it. in addition, the server - end design a database to manage from which the system could tackle users information and online users log in the form of winform and strengthen the safety of the system
Net平臺下的ado . net與asp . net技術，發揮兩者的武漢理工大學碩士學位論文優勢，構造了功能更強的遠程監控系統，更好的滿足用戶的需要。系統設計中以asp . net架構為前臺環境，實現了客戶端通過ie瀏覽器來實時的監控到排水泵站的運行情況，使系統達到了實時監視，但由於大泵機工作電壓高（ 6000v ）功率大（ 100okw ）的特點，暫不採用客戶端控制系統。在服務端，設計了數據庫，並且以winform的形式來管理網路管理員和用戶的信息以及在線用戶的日誌，加強了系統的安全性。 -
This system consists of a full bridge pwm ( pulse width modulation ) regenerative rectifier or so - called vsc ( voltage source converter ) that connected to pcc ( point of common connection ) at the power utility grid through a passive interface circuitry
這種系統包括一個pwm全橋可逆整流器或者所謂的電壓源變換器，通過無源電路介面與電網的pcc點（公共連接點）相連。 -
Circuit breaker for full - voltage circuit
全電?迴路遮斷器 -
Magnetic full voltage starter
電磁全電壓起動器 -
Because this is an identification in a no - load full voltage starting mode, so there are some estimations which can bring some errors. so the following work should emphasis on how to get more exact parameters. and we can also expand this project not only identify the motor ' s parameters but also its other characteristic
在本項目中，由於試驗條件所限，還是在一定程度內進行了近似計算，因此，在第五章的總結與展望中，作者提出本課題的兩個發展方向，一個是向更精確的方向發展，一個是在參數辨識的基礎上，進行電機其他特性的計算與檢驗。
分享友人