gas manifold 中文意思是什麼
gas manifold
解釋
氣體管線-
The exhaust gas exits through the other exhaust manifold.
廢氣經另外一個排氣歧管排出。 -
In the case of a single medicinal gas filled via a multi - cylinder manifold, at least one cylinder of product from each manifold filling should be tested for identity, assay and if necessary water content each time the cylinders are changed on the manifold
在用多頭分配器給多個氣瓶灌裝同一種醫用氣體的情況下，對每組多頭分配器至少要對一個氣瓶進行鑒別和分析，必要時，每次更換氣瓶時還須測定水份含量。 -
The analysis model and design methodology for the gas field are discussed referring to related documents. the structure parameters of gas manifold, channel, diffusion layer and hydrophobic layer which affect the oxygen distribution are also studied
本文闡述了氣場分析模型和設計思想，研究了進氣箱、交指型流道、擴散層和疏水層結構參數對氧濃度分佈的影響。 -
The result shows that multiple inlet is better than single inlet, and that inlet with buffer is better than that without buffer. other optimal design structures are also adopted. the gas manifold with optimal structure make oxygen much evener for each cell
結果表明多進口比單進口，有）比無隔板、擴壓型進口比非擴壓型進口、橢圓臺進口比圓臺進口的進氣箱結構更易實現電池堆中每個單電池進氣量的均勻化。 -
The gas field in pemfc means the gas distribution in gas source, gas inlet tube ( scale of m ), gas - blower, gas manifold ( scale of cm ), channel ( scale of mm ), diffusion layer ( scale of um ), hydrophobic layer and catalyst layer ( scale of nm ). the aim of changing the scales is to make oxygen reach reaction area as evenly as possible
Pemfc的氣場指在氣源、進氣管（分米級） 、風機、進氣箱（厘米級） 、流道（毫米級） 、擴散層（微米級） 、疏水層（亞微米級） 、催化層（納米級）中的氣體分佈，每一級尺度的變化是為了氣體的進一步均勻化。 -
The exhaust gas spews out of the exhaust valve and enters into the muffler along the exhaust manifold before draining into the atmosphere from the tail pipe. this process yields wide band exhaust noise
發動機廢氣從排氣門高速沖出，沿著排氣歧管進入消聲器，最後從尾管排入大氣，在這一過程中產生了寬頻帶的排氣噪聲。 -
Gas welding equipment - acetylene manifold systems for welding, cutting and allied processes - safety requirements in high - pressure devices
氣焊設備.焊接切割和相關工藝用乙炔總管系統.高壓裝置的安全要求 -
The exhaust noise contains complex noise elements, including the exhaust noise with a base frequency measured in the number of exhausts in unit time, the resonance noise of the gas column in the pipe, the gas stream blowing noise at the exhaust manifold, the exhaust gas jetting and impact noise, the helmholtz resonance noise of the cylinder, the karman eddy noise and the turbulent noise inside the exhaust system
排氣噪聲包含了復雜的噪聲成分：以單位時間內排氣次數為基頻的排氣噪聲、管道內氣柱共振噪聲、排氣歧管處的氣流吹氣噪聲、廢氣噴注和沖擊噪聲、汽缸的亥姆霍茲共振噪聲、卡門渦流噪聲及排氣系統內部的湍流噪聲等。 -
When volume efficiency is computed by an engine cycle simulation considering gas flow in intake and exhaust manifold as one - dimensional unsteady flow, improperly given parameters in the simulation may cause an error over 5 %
摘要採用進排氣管流動為一維非定常模型的發動機循環模擬方法計算充氣效率時，若模型中給定的參數不合適，可能引起充氣效率的計算誤差超過5 % 。 -
Gas welding equipment. acetylene manifold systems for welding, cutting and allied processes. general requirements
氣焊設備.焊接切割和相關工藝多功能乙炔系統.一般要求 -
Gas welding equipment - acetylene manifold systems for welding, cutting and allied processes - general requirements
氣焊設備.焊接，切割和有關加工工藝用的乙炔導管系統.一般要求 -
Gas welding equipment - pressure regulators for manifold systems used in welding, cutting and allied processes up to 300 bar
氣焊設備. 300bar以下的焊接切削及相關工藝用匯流系統用壓力調節器 -
Gas welding equipment - acetylene manifold systems for welding, cutting and allied processes - general requirements iso 14114 : 1999 ; german version en iso 14114 : 1999
氣焊設備.焊接切割和相關工藝用乙炔匯流系統一般要 -
Gas welding equipment - acetylene manifold systems for welding, cutting and allied processes - safety requirements in high - pressure devices iso 15615 : 2002 ; german version en iso 15615 : 2002
氣體焊接設備.焊接切割和相關工藝用乙炔總管.高壓 -
The medicinal gases filling manifold as well as the cylinders should be dedicated to a single medicinal gas or to a given mixture of medicinal gases ( see also 3. 2. 2 )
醫用氣體灌裝分配器和氣瓶應專用於一種醫用氣體或一種特定的混合氣體。
分享友人