gauge size 中文意思是什麼

gauge size 解釋
計量尺寸
  • gauge : n 1 規，量規，量器，量計，表。2 標準尺寸，標準規格；（金屬片等的）厚度，（槍炮的）口徑，（電線等...
  • size : n 1 大小，尺寸規模身材。2 （鞋帽等的）尺碼，號；（紙張的）開。3 巨大，大量；相當大的分量。4 〈口...
  1. Railway transport equipment. connection for flange intercommunication for standard - gauge line stock. size and fastening - measurements and tolerances

    鐵路運輸設備.標準軌距鐵路車輛的法蘭互聯裝置的連接.尺寸連接測量和公差
  2. Water system. swith for pressure gauge. type and size

    水系統.壓力表開關.型式與尺寸
  3. For confirming the results, a full - size model ( dj / dj = 0. 6, t / t = 1. 5 ) was analyzed by means of strain gauge test. the reliability of finite element analysis was proved because the results basically accorded with that of the test. secondly, in this paper, in order to carry out a fair assessment of the reinforcement design on spherical shell with transnormal nozzle, a comparison of reinforcement method was done between jb4732 - 1995 steel pressure vessels ? esign by analysis appendix a4 and hg20582 - 1998 specification for stress calculation of steel chemical vessels

    為了驗證ansys分析結果的可靠性，對其中一組參數下（開孔率0 . 6 、厚度比1 . 5 ）的模型容器，採用電測法進行了應力測試，並將得到的實驗結果與有限元結果進行了比較，二者在應力分佈狀況和大小上均基本吻合，證明此種結構運用ansys進行分析，其結果是完全可靠的。
  4. When threading pipe, gauge pipe threads for size and length to avoid jamming pipe against seat and disc

    當對管道進行攻絲時，要測定管道螺紋的尺寸和長度，避免將管道塞滿閥座和閥瓣。
  5. Firstly, the strain gauge method was used to measure the time difference of stress wave passing through two gauges adhered on the surface of test piece and also their main frequencies secondly, a 3 - component dynamometer was used to measure the resonant frequency of timber six kinds of full size timber were used for test

    本研究旨在研發兩種新的應力波計測技術，其一為利用應變規來測定兩標點間之應力波傳遞時間差及試材之共振頻率，藉以計算試材之音速及動彈性系數，其二為利用三向動力計來測定試材之共振頻率。
  6. And be sure to bring the same kind of socks you wear to a match so that you can accurately gauge what size shoe you need

    確保帶上你比賽時穿的同種襪子，這樣你可以精確選擇你需要的鞋號。
  7. The optimeter is widely used to precisely measure external size of workpiece by comparison with a gauge block or standard part

    本儀器是一般是用標準器（如量塊）以比較法測量工件的尺寸。
  8. 1 4 specification for screw gauge limits and tolerances - limits of size for gauges for screw threads of unified form diameters 1 4 in and larger

    螺紋量規極限和公差規范.第4部分:直徑1 4英寸以上
  9. Blood essels causing edema of the lower legs were measured using a strain gauge plethysmography ( a general instrument for determining and registering ariations in the size of an organ or limb )

    利用應變容積描記術（用於測量並記錄器官或四肢的尺寸一種通用方法）測量低位腿部水腫患者的血管直徑。
  10. Britain ' s environment department commissioned two pieces of work that attempted to gauge the likely size of both the direct and indirect rebound effects across the economy

    英國環境部門授權了兩項工作，用以測定在國家經濟中這些直接回彈與間接回彈的可能出現的程度。
  11. Precision test gauge according to en 837 - 1 with bourdon tube, nominal size nd 160 mm, connection position bottom or back eccentric, accuracy class 0. 6

    高精度波登管校驗表，符合en 837 - 1 ，標準尺寸表徑160mm ，介面位置底部或後方軸向，精確等級0 . 6 。
  12. Test gauge according to en 837 - 1, all stainless steel with bourdon tube, nominal size nd 160 mm, connection position bottom or back eccentric with or without glycerine filling, accuracy class 0. 6

    全不銹鋼波登管校驗表，符合en 837 - 1 ，標準尺寸表徑160mm ，介面位置底部或後方軸向，有或沒有甘油填充，精度等級0 . 6 。
  13. The technique that used to measure the mechanical properties for mems is different from the traditional one considering the size scale. a uniaxial tension test system for test the mechanical property of mems materials is presented in this thesis. the strain is measured by interference strain / displacement gauge ( isdg )

    本文介紹了新近研製的用於測量微電子機械繫統mems材料的機械性能的單軸拉伸試驗系統，採用激光干涉技術測量試樣應變，得到材料從開始變形直至破壞的全歷程應力應變曲線。
分享友人
分享到 Line

分享到臉書