gear check 中文意思是什麼
gear check
解釋
起落架檢查-
The thesis developed the optimization design software of geometric parameter for the worm gear including strength check module, the drawing contact lines module, the change lines of tooth thickness of worm, and the parametric modelling software for the reducer which includes parametric modelling of parts and assembly. the cad prototype system is very convenient because of its accessible interfere, simple operation and written in chinese. by input design parameters ， the cad system can make optimization design and strength check for the worm gear ， draw contact lines of tooth flank of worm - gear and change line of tooth thickness of worm ， judge if the tooth flanks of worm undercut and if the sideward tooth of worm - gear hob come to a point ， make project design and structure design for the reducer and draw its 2d parts and assembly
研究和開發了平面二次包絡環面蝸桿傳動的參數優化設計和校核軟體系統：包括幾何參數設計計算模塊，強度校核模塊，繪制齒面接觸線模塊，蝸桿齒厚變化曲線模塊和蝸桿根切判別模塊；開發了平面二次包絡環面蝸桿減速器外形與結構尺寸數據庫以及傳動效率數據庫，建立了平面二次包絡環面蝸桿傳動公差及極限偏差數據庫；開發了平面二次包絡環面蝸桿減速器參數化建模軟體：包括零部件的參數化建模模塊和裝配圖的參數化建模模塊，其中零部件的參數化建模包括蝸桿軸系的參數化建模、蝸輪軸系的參數化建模、箱體的參數化建模、端蓋的參數化建模、軸承的參數化建模和其它零部件的參數化建模軟體模塊。 -
After being improved, the gear surface contact fatigue strength obeys weibull distribution and stress obeys normal distribution, the gear bottom bend fatigue strength and stress obey logarithm normal distribution, according to the relation of average safe rate and reliability, then the gear strength reliability design and check equations can be deduced
將齒面接觸疲勞強度按威布爾分佈、應力按正態分佈處理，將齒根彎曲疲勞強度和應力均按對數正態分佈處理，再根據平均安全系數和可靠度之間的關系，推導出了齒輪強度可靠性設計和校核公式。 -
Check the gear wheel drive in the groove of the wall, select four gear wheel ( red pinion is not used ) of different size for use, load heavy gear wheel, times of heavy gear wheel, times of light gear wheel, minimum gear wheel most onto separately from left to right, make gear wheel hand in, form each other, leave behind, operate a switch, drive, finish
檢查墻壁凹槽中的齒輪驅動裝置，選用大小不同的四個齒輪（紅色的小齒輪不用） ，從左到右分別裝上最大的齒輪、次大的齒輪、次小的齒輪、最小的齒輪，並使齒輪間相互交結，拉下拉閘，驅動完成。 -
1 set of 3101 integrative gear check - instrument
3101型輪綜合檢查儀1臺 -
Request a low flying over the runway for gear check
請求低空飛行通過跑道檢查起落架。 -
The design manual falls into three parts : chapter 1, as the overal design part, mainly descirbes how to determine which mechanisms with what metal structures shall be used and illustrates how to design its boom structure and balancing system, including point search, calculation and check ; chapter 2 introduces how to design the crane ' s running gear, including model selection, wheel pressure calculation and overall stability check ; and chapter 3 deals with model selection of its lifting mechanism and related calculations
說明書詳細的介紹了該型號起重機的總體設計及行走機構設計和計算過程，總共分為三章：第一章為起重機總體設計部分，主要內容是起重機各機構和金屬結構型式的確定，並用作圖法對臂架結構和平衡系統進行設計，包括了機構找點，驗算及校核；第二部分是運行機構的設計計算，包括了運行機構的選型，輪壓計算，整機穩定性校核；第三部分為起升機構的傳動方案選型和設計計算。 -
Check visually if gear and tyre are intact, do not retract the landing gear until fire is out
請目視檢查起落架及輪胎是否完整無損，火熄滅后才收上起落架。 -
Abstract : this paper derives thecalculating formulas to the contact strength and oil - film thickness of the involute spur gear according to hydrodynamic lubrication principle. through check with test, shows that they may rully replace now available hertz formula and dowsonformula respectively
文摘:根據流體動力潤滑原理，推導出了漸開線直齒圓柱齒輪接觸強度及油膜厚度的計算公式，通過實驗驗證，說明它們可以完全分別代替現有的赫芝公式及通森公式。 -
Right main well on fire, we extended landing gear to avoid damage, returning to base for a thorough check
右主輪艙失火，我們放下起落架避免燒壞，返回基地進行徹底檢查。 -
Design on torque check circuit using for gear test bed
電加載變速箱試驗臺轉矩的檢測電路 -
Now landing gear fully extended, three greens on, over the field. please give me a visual check on the landing gear
現在起落架完全放下，三個綠燈亮，飛越機場。請給予我目視檢查起落架。 -
On the basis of analyzing the respective development and current situation at home and abroad of cad / cae / capp technology, this paper brings forward the research direction - integration and intelfectualization combining the expert system. by the analysis of the characteristic and restriction of the gear components, this paper upbuilds the characteristic model based on the restriction and actualizes data transmission and information sharing among cad. cae and capp. this paper analyzes the general principle of parameter determination and strength check about gear and researches the algorithmic of gear strength check based on the characteristic. this paper introduces expert knowledge into respective procedure of cad. cae and capp and actualizes the intellectualization in design process. strength analysis and process planning. on the basts of aforementioned research. this paper develops the cad / cae / capp integration software of gear components by means of the active - automation technology provided by autocad and vb and conducts the integration with general mechanical and shaft components integrated designing system. the application of the software indicates this system has perfect function and project applied cost
本文在分析國內外cad cae capp技術各自的發展歷史與現狀的基礎上，結合專家系統，提出了智能集成的研究方向。以齒輪類零件作為研究對象，在分析了其特徵及約束的基礎上，利用數據庫技術和圖形單元建模技術，建立了基於約束的特徵模型，實現了cad cae capp之間的數據傳輸和信息共享；分析了齒輪參數確定、強度校核的一般原則，進行基於特徵的齒輪強度校核的演算法研究；將專家知識融入在cad 、 cae 、 capp各個過程中實現了設計過程、強度分析和工藝分析的智能化。在上述研究的基礎上，利用autocad2000提供的activexautomation技術，以vb為開發工具，開發出了齒輪的cad cae capp集成軟體，並與其它機械通用件設計系統進行了集成。 -
On the basis of analyzing application situation of cad / cae / capp technology at home and abroad, this paper brings forward the research direction ? integration and intellectualization combining the expert system. by the analysis of the characteristic of each part of worm gear, this paper upbuilds the characteristic model of worm gear based on the restriction and actualizes data transmission and information sharing among cad, cae and capp. this paper analyzes the general principle of parameter determination and strength check about worm gear and researches the algorithmic of strength check based on the characteristic about worm gear. this paper introduces expert knowledge into respective procedure of cad, cae and capp and actualizes the intellectualization in design process, strength analysis and process planning. on the basis of aforementioned research, this paper develops the cad / cae / capp integration software of gear components by means of the active - automation technology provided by autocad and vb. the applic ation of the software indicates this system has perfect function and project applied cost
本文在分析cad / cae / capp技術在國內外應用概況的基礎上，結合專家系統，提出了智能集成的研究方向。以蝸桿傳動的各個零件作為研究對象，在分析了各自特徵的基礎上，利用數據庫技術和圖形單元建模技術，建立了蝸桿傳動的特徵模型，實現了cad / cae / capp之間的數據傳輸和信息共享；分析了蝸桿傳動中參數確定、強度校核的一般原則，進行了基於特徵的蝸桿傳動強度校核的演算法研究；將專家知識融入在cad 、 cae 、 capp各個過程中實現了設計過程、強度分析和工藝分析的智能化。在上述研究的基礎上，利用autocad2000提供的activexautomation技術，以vb為開發工具，開發出了蝸桿傳動的cad / cae / capp集成軟體。 -
Check the indication of pressure gauge on central landing gear strut
請檢查中起落架減震支柱指示。 -
Then the machine can directly check out the gear parts, which has transmission fault. the frequency spectrum analysis is applied to analyze measuring results
利用本系統能直接對齒輪傳動質量進行檢驗，並可利用分析技術對測量結果進行分析。 -
Check completed, i think gear is still jammed, but i ' m not quite positive about it. request foam carpet
已檢查過了，我想輪子仍被卡死，但我不十分肯定它，請求在跑道上噴灑泡沫墊。
分享友人