glass transition 中文意思是什麼

glass transition 解釋
玻變
  • glass : n 1 玻璃，玻璃狀物。2 〈集合詞〉玻璃製品，玻璃器具，料器；玻璃暖房 （＝glasshouse）。3 玻璃杯；一...
  • transition : n 轉變，演變，變遷，變化；飛越；過渡期；【音樂】變調，轉調；【修辭學】語次轉變；【語法】轉換；【...
  1. The glass-transition is a cooperative phenomenon.

    玻璃轉化是一個協同作用的現象。
  2. Dsc for the nanocomposites showed the glass transition temperature ( tg ) of the nanocomposites increases slightly as the mmt content increases. water absorption velocity and water retentivity under pressure tests showed the addition of montmorillonite ( mmt ) can improve the beginning absorption velocity and water retentivity for pure superabsorbent resin

    吸水速率和加壓保水能力測試表明，一維納米級蒙脫土片層的引入能在一定程度上提高高吸水性樹脂的初期吸水速度和加壓下的保水能力。
  3. Swelling test, dsc and tg were used to determine the solubility parameter, glass - transition temperatures and thermolysis temperatures of polycondensates

    使用溶脹試驗、 dsc 、 tg對其溶度參數、玻璃化轉變溫度、熱分解溫度等參數進行了測定。
  4. If the surfaces of baso4 particles were not modified with couplant, the interface was clear with a very small adhesive force ; while the surfaces modified, the interface was fuzzy with a strong adhesive force. the glass transition temperature ( tg ) of baso4 / tpu blend was obtained by dma

    當baso _ 4表面未用偶聯劑處理時， baso _ 4 / tpu共混體系相界面清晰，界面粘合力較小；當baso _ 4表面用偶聯劑處理后， baso _ 4 / tpu共混體系相界面模糊，界面粘合力強。
  5. Then by means of heterocoagulation and encapsulatin, on controlled condition the superfine powders of caco3 and tio2 were coated with different nonaparticles ps. the composite particles with core / shell structure were prepared by heating the composite particles above the glass transition temperature of ps

    然後根據異相凝集-包埋法原理對具有不同表面電性的微米級的caco _ 3和tio _ 2進行包埋復合，制得以無機粒子為核，有機粒子為殼層的包覆型有機?無機復合粒子。
  6. By reducing bromine content and adding aluminum hydroxide in the surface of substrate for the printed circuit board, comparative tracking index ( cti ) of the substrate is improved significantly, meanwhile the size stability, heat resistance, the glass transition temperature of the substrate are improved too

    摘要通過降低印製電路板的基板表層的嗅含量並加入氫氧化鋁，顯著提高了基板的相比漏電起痕指數（ cti ） ，並同時提高了基板的尺寸穩定性、耐熱性、玻璃化溫度。
  7. National key laboratory of advanced composites ( lac ) in beijing institute of aeronautics materials ( biam ) has developed a new medium temperature curing epoxy resin system, of which the glass transition temperature is 119. 88, for resin transfer molding ( rtm ). in order to investigate the relation between viscosity and time - temperature, the rheological behavior of the system was studied by dsc and viscosity experiments. a rheological model based on the dual - arrhenius equation was established and used to simulate the rheological behavior of the resin, which was in good agreement with experimental data

    本文表徵了北京航空材料研究院先進復合材料國防科技重點實驗室樹脂組新開發出的rtm用中溫固化環氧樹脂體系3266 （玻璃化轉變溫度為119 . 88 ）其粘度隨時間、溫度的變化關系，在粘度實驗和dsc熱分析實驗的基礎上，對用於rtm工藝的該環氧樹脂體系的化學流變特性進行研究，並根據雙阿累尼烏斯方程建立樹脂體系的流變模型。
  8. Test results show that that the breakcown voltage and heat distortion temperature the encapsulating materials of epoxy resin with hgh are famously improved, but the the addition of hgh, the viscosities of the epoxy resin - hgh system is higher compared with that of the others and the encapsulating process is effected. nano - sio2 improves the mechanical properties of encapsulating materials of epoxy resin, impact strength reaches 27. 64kj / m2 from 13. 95 kj / m2, flexural strength reaches 136. 68mpa from64. 95 mpa. by addition of the montmorillonite, glass transition temperature and heat distortion temperature of the encapsulating materials are 13. 2 and 16 higher than that of epoxy re

    結果表明，活性硅微粉對環氧灌封材料的熱變形溫度和電學性能提高較為顯著，尤其在浸水后，電學性能降低幅度很小，西北工業大學碩士學位論文但活性硅微粉用量較大，材料的工藝性能明顯降低;納米5102對環氧灌封材料具有顯著的增強和增韌作用，沖擊強度、彎曲強度由原來的13 . 95kj / mz和64 . 95mpa分別提高到27 . 64kjzm2和136 . 68mpa 。
  9. For the crystalline polymer matrix, the ptc transition temperature is close to the melting point, while for the amorphous polymer matrix, the ptc transition temperature is close to the glass transition temperature

    Ptc轉變溫度與體積膨脹的轉變溫度非常一致，對于結晶聚合物基體體系， ptc轉變溫度在基體的熔點附近，而對于非晶聚合物基體體系， ptc轉變溫度在基體的玻璃化轉變溫度附近。
  10. The polymer of p - tert - butylstyrene ( tbs ) has a relative high glass transition temperature and is soluble in aliphatic solvent. it has a comprising prospect of application in many areas including the development of novel materials, theoretical research, dispersion polymerization, unpolluted paints, oil additives, and so on

    對叔丁基苯乙烯聚合物具有較高的玻璃化溫度，並且能溶於脂肪烴中，使其在新型材料的開發、理論研究、分散聚合、環保油漆和油品添加劑等領域有廣闊的應用前景。
  11. Glass transition temperatures decreased with the length of soft units increasing, however, the effects of soft units were random

    隨柔性間隔基k度的增加，玻璃化轉變溫度卜降，但柔性間隔基對熔點的影響是無規律的。
  12. Standard practice for glass transition temperatures of hydrocarbon resins by differential scanning calorimetry

    用差分式掃描熱量儀測定碳氫化合物樹脂玻璃導熱溫度的標準實施規程
  13. The paper focuses on the processing technique of wood flour - recycle polystyrene composite, and assesses the effects of wood flour contents, coupling agent contents and the rotate speeds of extruder on water uptake, tension strength, bending strength and dynamic mechanical properties. the results can be shown as follows : with the increasing of wood flour, composites gain higher water uptake but lower dynamic mechanical properties, the storage moduli ( e " ) and glass transition temperature ( tg ) decrease

    較系統地研究了木粉含量、偶聯劑添加量和雙螺桿擠出機的螺桿轉速等主要擠出工藝參數對復合材料的吸水性能、拉伸強度、彎曲強度、動態機械性質（存儲模量e和損耗正切角tan ）的影響規律，初步確定了適宜工藝條件，主要結論是： 1 ）木粉含量的增加使得復合材料的吸水性能增加，動態機械性質下降。
  14. Comparison of the diffusion coefficients calculated by this new model with the present experimental data, including benzene, toluene, ethylbenzene in polystyrene ( ps ) and poly ( methyl methacrylate ) ( pmma ) are performed, calculation results in this study are in good agreement with experimental data, for the correct estimation of the hole - free volume change above and below the glass transition

    以芳香族溶劑苯、甲苯、乙苯在玻璃態聚苯乙烯和聚甲基丙烯酸甲酯中的擴散系數為例對模型進行驗證，理論計算結果和實驗值取得良好一致。
  15. Standard test method for assignment of a glass transition temperature using thermomechanical analysis under tension

    拉力下熱機械分析的玻璃轉變溫度分配的標準試驗方法
  16. Glass transition temperature

    玻璃轉換溫度
  17. Crystallinity, glass transition temperature

    玻璃轉移溫度
  18. Standard test method for assignment of the glass transition temperature by thermomechanical analysis

    使用熱機分析測定玻璃轉變溫度的標準試驗方法
  19. Standard test method for assignment of the glass transition temperature by dynamic mechanical analysis

    用動態力學分析測定玻璃轉變溫度的標準試驗方法
  20. Meanwhile, the choose of monomers composition, the amount of curing materials, the token of surface characteristic and the glass transition temperature of fluorited polymers were discussed, with the help of ft1r, dsc, and sem analysis

    對配方選擇、固化劑的用量及含氟量進行了討論。利用ftir 、 dsc 、 sem等方法，對兩種含氟聚合物成膜性能、玻璃轉化溫度及膜的表面特徵進行了表徵。
分享友人
分享到 Line

分享到臉書