hardening thickness 中文意思是什麼

hardening thickness 解釋
硬他厚度
  • hardening : n. 1. 硬化；【冶金】淬火。2. 硬化劑。
  • thickness : n 1 厚；粗；厚度；粗大。2 濃度，濃厚，黏稠。3 密度；稠密。4 模糊不清，多煙霧，混濁。5 愚笨；遲鈍...
  1. The springback angle increases with the increase of the punch round radius and clearances between the punch and the die while decreases with increase of the blank holder force, sheet thickness, friction coefficient and material hardening exponent

    回彈角隨凸模圓角半徑和凸凹模間隙的增大而增大，隨壓邊力、板料厚度、摩擦系數和材料硬化指數的增大而減小。
  2. 3. based on the bond test for 33 concrete specimens and gfrp and bending test for 15 beams strengthening with gfrp, surface preparation of concrete, type of epoxy adhesives, thickness of adhesives, hardening time of adhesives, cure condition after strengthening are considered, and the effect on concrete structures strengthening with gfrp causing by construction behavior was analyzed. 4

    根據gfrp片材加固混凝土結構在施工中常涉及到的一些相關因素，如混凝土基層表面處理情況、所選用的粘結劑類型、塗抹粘結劑的厚度、加固的方式以及養護狀況，進行了33個混凝土試件與gfrp片材的剪切粘結試驗，並進行了採用gfrp片材加固的15根混凝土梁的抗彎試驗，分析了與施工性能相關的因素對gfrp片材加固混凝土結構效果的影響。
  3. Moreover, it showed that the linearity rising relations were existed between the laser power and the thickness of hardening layer, and the linearity negative rising relations between the scanning velocity and peak rigidity

    此外，結果還表明激光功率與淬硬層厚度成線性增長，而掃描速度與峰值硬度成線性負增長關系。
  4. The study of the effect of material properties and dimensions and loading currents on liner buckling, using a capacitor bank as a driver, indicates that the mode number for buckling increases with the ratio of radius to thickness of a liner, and the yield strength to plastic hardening modulus, but keeps invariable with the increase of loading current, and that the magnitude of buckling increases with the loading current

    用電容器組脈沖發生器裝置作為驅動源，設計4種不同材料、不同尺寸的金屬套簡，通過調節電容器組的充電電壓得到不同的加載電流，研究材料及幾何參數、加載脈沖特性對套簡屈曲的影響；採用瞬態非線性有限元方法對實驗結果進行了數值模擬。
  5. By analyzing the simulation results, how the hardening parameter, bend radius parameter and thickness parameter influence springback is studied

    通過對模擬結果的分析，研究了硬化指數、彎曲半徑、材料厚度等因素對回彈的影響規律。
  6. Some interest has been generated in studying the rationale for assisted hatching. some reports suggest that embryos with lower zona pellucida thickness ( zpt ) and higher zona pellucida thickness variation ( zptv ) had a better chance of successful hatching and so the patient become pregnant ; another reports suggest that in vivo aging ; in vitro culture and exposure to ultralow temperature may induce zona hardening and then impair the embryo ability of hatching

    有作者提出胚胎透明帶厚度（ zonapellucidathickness ， zpt ）小的胚胎孵出時阻力減小，而透明帶厚度變化率（ zonapellucidathicknessvariation ， zptv ）高的胚胎由於透明帶上有一個明顯薄的區域而使胚胎易於孵出；還有作者推測病人年齡、體外培養天數的增加及冷凍處理會增加透明帶的硬度，使胚胎孵出困難。
  7. A mechanical model of conical part stamping process is built under the conditions of considering thickness variation, anisotropy, work - hardening, friction factor and so on

    摘要在綜合考慮板厚變化、各向異性、加工硬化及摩擦等因素的情況下，建立了圓錐形件沖壓成形過程的力學模型。
分享友人
分享到 Line

分享到臉書