heat polymerization 中文意思是什麼

heat polymerization 解釋
熱聚合（作用）
  • heat : n 1 熱；熱力；熱度；熱量。2 體溫；發燒。3 （氣候的）高溫，暑氣。4 【冶金】熔煉的爐次；裝爐量；一...
  • polymerization : 聚合酌
  1. Anhydride-type curing agents require the application of heat to promote polymerization.

    酸酐類固化劑則要求加熱以促進聚合反應。
  2. The silicone and silicone emulsion, hydrophobic additive, were preparaed by the method of hydrolytic polymerization and emulsion polymerization, respectively. the technical factors and properties of the coating were optimized. the design mothod of the heat - insulated coating film was studied

    首先用硅氧烷水解聚合法和乳液聚合法制備了高效疏水性硅酮樹脂和有機硅乳液型疏水添加劑，並對制備工藝參數、性能進行了優化。
  3. Modification of ep by nano - sio2 and organic silicone was presented to enhance heat - resistant, wet - resistant and mechanical properties of ep cured system by review of nano - composites, modification of ep and nano - sio2. polymerization of epoxy resin and teos with dispersing nano - sio2 was studied

    用納米sio2和teos共同改性ep的酸酐固化體系，隨teos和納米sio2添加量的增加， si o si網路結構趨于完善，產物的耐高溫性能顯著提高。
  4. For many experiments, using high pureness mma, controlling polymerization temperature and polymerizing condition under high - pressure nitrogen gas and heat treatment after polymerization, a transparent preform without any bubble and blemishes was prepared. then drawing this preform, gi - pof with diameter 0. 8 - 1. 0mm was obtained. because of the limitation of the experimental conditions and the shortage of the money, it is very regretted that we ca n ' t test the index profile and the loss of the gi - pof accurately

    在系統研究界面凝膠法原理和聚合機理的基礎上，通過多次實驗總結、改進，在制備過程中採用提高精餾效率、控制溫度、加壓聚合、氮氣保護和後期處理等措施，制備出無氣泡及銀紋缺陷、光潔、透明的光纖預制棒，拉絲得到直徑0 . 8 - 1 . 0mm的gi - pof 。
  5. As the content of vermiculite minerals increased, the content of the " intercalated " shape, in which crystal gallery breadth was about of 40nm, also increased. in the curing reaction processing of polybenzoxazine / vermiculite hybrid nanocomposites intercalated with bisphenol a type precursor. according to the content of vermiculite minerals, while different shape of crystal was forming, these crystals were retarding the heat ring - opening polymerization of bisphenol a type precursors in the nanocomposites

    通過對雙酚a型ben蛭石納米插層物固化過程的分析：不同蛭石含量的插層物，在形成不同納米分散狀態固化結構的過程中，蛭石晶片對雙酚a型ben的熱開環聚合有明顯不同的阻礙作用，蛭石含量為3的插層物160的凝膠化時間較純樹脂的延長約7min ，活化能高約8kj mol ，固化反應熱晗低約14j g ，使得固化物的固化程度較純樹脂低約10 ，阻礙作用最大，其它含量的次之。
  6. At first, some preparative methods of magnetic microsphere were summarized, including physical and chemical methods such as spray evaporation, heat treatment, emulsion polymerization, self - assembly and so on

    首先介紹磁性微球的幾種制備方法，包括噴霧乾燥、熱處理等物理方法，以及乳液聚合、自組裝等化學方法。
  7. Abstract : focusing the key problem of liquid with high viscosity in heat transfer, experiments on mixing and reaction rate of hot liquid were carried out. a new polymerization process of methylvinyl silicone rubber was designed

    文摘:通過對現有甲基乙烯基硅橡膠生產工藝、過程和設備的分析研究，針對高粘度流體傳熱難度大的問題，進行了熱流體混合速度及反應速度的試驗，設計了一種生產甲基乙烯基硅橡膠的新工藝。
  8. Emulsion polymerization is a reaction system which can be characterized as a low - viscosity, good - heat - transference, and at the same time, the environment friendly. therefore, it is being widely used to prepare paints, vanishes, adhesives, rubbers and controlled drug release systems

    乳液聚合因具有體系粘度低、傳熱快、環保以及分隔效應等特點，其產物已廣泛運用於塗料、油漆、粘合劑、橡膠和藥物緩釋膠囊載體等領域。
分享友人
分享到 Line

分享到臉書