heat treatment the 中文意思是什麼

heat treatment the 解釋
熱處理
  • heat : n 1 熱；熱力；熱度；熱量。2 體溫；發燒。3 （氣候的）高溫，暑氣。4 【冶金】熔煉的爐次；裝爐量；一...
  • treatment : n 待遇；作業；處理，處置；討論，論述；【醫學】治療，療法；（種子的）消毒（處理）。 preferential t...
  • the : 〈代表用法〉…那樣的東西，…那種東西。1 〈用單數普通名詞代表它的一類時（所謂代表的單數）〉 （a） 〈...
  1. A heat treatment to composite membrane, preferred at a 70 hot air bath for 20 minutes can improve the salt resistance of the composite membrane

    對復合膜進行適當的熱處理可以進一步改善復合膜的脫鹽性能，以70熱空氣浴， 20min為宜。
  2. In our company we have forging, costing and heat treatment workshops with advanced producing equipments. all the tasks which refused by the other companies will be done well here. there are many large - size air hammers, blast furnaces and costing equipment including all sorts of heats treatment equipment, costing equipment including all sorts of heat treatment equipments

    我公司下屬鍛造鑄造熱處理加工廠各一座，有先進的生產設備，可以接收其它部門不願承攬，甚至不敢承攬的艱巨任務，我們有大型的空氣錘和高爐冶煉鑄造設施和場地，有淬火退火回火各種熱處理設備。
  3. There are three main operations in the heat treatment of steel: hardening, tempering and annealing.

    鋼的熱處理操作主要有三種，即：淬火，回火和退火。
  4. Effect of heat treatment on induced apatite deposition and bonding strength of the alkali treated titanium oxide layer for carbon carbon composite

    碳復合材料上堿液處理氧化鈦鍍層誘導沉積磷灰石和結合強度的影響
  5. Heat, in the form of hot baths and hot packs, has been widely acclaimed and accepted as an aid in the treatment of arthritic pain

    以熱水浴和熱袋形式的熱敷作為關節炎疼痛的輔助治療已經被廣泛地認同。
  6. That is the premise of the bg / ha electrophoresis codeposition. the laws of the electrophoresis deposition of the bg and ha partic les were found by the study on each of their deposition under the different conditions. the electrophoresis codeposition of the bg and ha particles had been studied and the bg / ha graded coating, which is compact in the bottom layer and porous near the surface layer, had been prepared on the surface of the dental implant after the low temperature heat treatment ( about 740 ) and fast firing ( 50 - 80 / min, heat preservation time was 5 - 8min. )

    以bg微粉和ha微粉作為塗層原料，通過研究bg和ha微粉在非水介質中的分散情況和帶電特性，選擇冰醋酸為介質，使分散在其中的bg顆粒和ha顆粒表面均帶上正電荷，為電泳共沉積提供前提條件；通過對不同條件下bg 、 ha各自電泳沉積的研究，探索出了兩者電泳沉積的規律；通過對bg和ha在冰醋酸中電泳共沉積以及后續低溫（ 740左右）快燒（ 50 ? 80 min ，保溫5 ? 8min ）熱處理的研究，在鈦合金牙根種植體基體上成功制備出了底層緻密而表層多孔的bg ha梯度塗層。
  7. In this paper, 6013al / sicp / gr metal matrix composite ( mmc ) was produced by spray codeposition, by means of changing the medium of quenching, influence of five types of heat treatment system ( furnace cooling, air cooling, water quenching, dry ice quenching, liquid nitrogen quenching ) and different aging temperature on the damping was studied systematically

    本文採用噴射共沉積方法制備了6013al sicp gr金屬基復合材料（ mmc ） ，通過改變淬火介質，較為系統地研究了五種熱處理制度（爐冷、空冷、水冷、乾冰冷及液氮冷）以及不同時效溫度（ 120 、 150 、 170 、 190及210 ）對6013al sicp grmmc阻尼性能影響。
  8. Sagging and creep of the compo ? nents occur during heat treatment as a result of improper support of components or warped hearth in the hardening furnace

    當對部件支持不當或在爐床翹曲的淬火爐中進行淬火時，部件在熱處理過程中會出現弧垂和蠕變現象。
  9. This paper describes the structure, technical features and technical requirements of manufacture of a gasification stove with four contraposition burners on side walls, expatiates on its manufacturing process, key techniques and quality guarantee measures such as barrel formation, machining, assembly welding, heat treatment, subassembly secondary machining and precision detection

    摘要氣化爐是煤化工的核心設備，大慶油田金屬結構廠與哈爾濱鍋爐廠合作，為某大型石化企業製造了一臺側壁4個燒嘴對置式新型氣化爐，該氣化爐是目前國內同類產品中最大的氣化爐。
  10. Based on the analyses on mechanical properties, microstructure and fracture of - the microalloyed steels socrv with various heat treatment technique, it can be affirmed that various fractures arttribute to various mechanism, we can draw conclusion that the strength and toughness of microalloyed steels 50crv will be increase simultaneously by optimal heat treatment technique. to illustrate the mechanism of the strength and toughness of microalloyed steels socrv, we designed the comparative experiment and observed the microstructure of the sample which occurred at different quench and tempering temperature and different tempering time. the last experiment results were determined by the four factors : fined microalloyed elements grains, the decompound of martensite, martensite transformation of remnant austenite and the second phase precipitation

    為解釋微合金化50crv鋼強韌化機理，本文通過對不同淬火溫度，回火溫度，回火時間下的力學性能指標的對比及顯微分析，認為微合金元素的細化晶粒，馬氏體的回火分解，殘余奧氏體的轉變，第二相的沉澱析出共同決定了微合金鋼的強韌化情況，特別是由於微合金元素的存在，其細化晶粒及其碳氮化物的沉澱析出，導致鋼的良好的強韌性，並且如果工藝滿足第二相的沉澱析出強化大於回火馬氏體分解引起的軟化效應，會在硬度曲線中產生明顯的二次硬化現象。
  11. In regard to the low wear resistance of the white iron shot in the practical application, based on experimental research and trial production, by alloying and proper heat treatment, the shot can be made with higher hardness, better toughness and increased service life

    摘要針對白口鐵丸在實際應用過程中不耐磨的現象，通過大量實驗研究和試生產，找到通過添加合金元素生產合金鐵丸，並通過適當熱處理等手段，使其既具有較高硬度，又有良好的韌性，使用壽命得到提高，滿足拋丸工作的需要，節約大量資金，提高了勞動生產率。
  12. A tio2 layer prepared by dipping in the stable tio2 sol was deposited on the surface of etched aluminum foils. after heat treatment, the composite oxide films were prepared by a normal formation

    將鋁腐蝕箔在此穩定的溶膠中浸漬處理，高溫熱處理后將其陽極氧化，得到復合氧化膜。
  13. With the very low water to cement ratio, rpc has ultra - high strength high ductility and low permeability. in this paper, the compressive strength of rpc can reach to a high point with the number approximately 135mpa. as illustrated from the study results, we can approve some fundamental conclusions : there are big effects on rpc with deferent kinds and properties of raw materials and deferent curing conditions ; stress - strain curve shows the process of destroy with rpc samples ; x - ray diffraction analysis indicates that heat treatment at temperatures 90 accelerate the hydration of rpc sharply, therefore, mechanical and microstructural properties of rpc are highly dependent on heat treatment ; it is believed that rpc materials have excellent resistance to chloride permeability ; during the heat treatment, the shrinkage of rpc developed quickly because of chemical reactions ; the rpc with slag mostly has the advantage of rpc without slag about resistance to solutions corrosion

    研究結果表明：通過對rpc各組分摻量變化的研究，可以找到rpc的最優配合比；試件成型后的熱養護制度對rpc的性能影響巨大； rpc的抗壓應力?應變曲線可以反映出試件受破壞時微裂紋的擴展情況，剛纖維的摻入可以大幅改善rpc的韌性； rpc在成型后存在較大的收縮，而其中的化學收縮要遠遠大於乾燥收縮； rpc具有很強的抗氯離子滲透性能，漿體的密實度很高；通過x射線衍射實驗，可以發現rpc的膠凝體中ch晶體已經幾乎不存在，膠凝體主要由c - s - h凝膠和未水化水泥顆粒組成；在抗溶液侵蝕的實驗中，摻礦渣rpc的抗溶液侵蝕性能在絕大多數情況下要好於不摻礦渣試件，酸、堿溶液和浙江工業大學碩士學位論文摘要一些鹽溶液都會對rpc的結構產生侵蝕作用，但是機理各有不同。
  14. During the culture of the porcine ear skin fibroblasts, the successful rate was increased by selecting culture methods, contrasting donor age and improving culture condition. the rate of living cells in the method of combining trypsin cold treatment with trypsin heat treatment was much higher than that in the method of trypsin heat treatment. the results showed that the method of combining trypsin cold treatment with trypsin heat treatment had less adverse effects on cells than the method of trypsin heat treatment

    在培養豬耳皮膚成纖維細胞時從篩選細胞分離方法、比較供體年齡和改善培養條件這三方面著手提高培養的成功率。實驗中發現胰蛋白酶冷熱處理結合法培養的細胞存活率明顯高於胰蛋白酶熱處理法，說明使用胰蛋白酶冷熱處理結合法對細胞的不利影響較少，細胞產量較高。
  15. In chapter four, in our experiments, we selected four representative mould steels as samples. after laser heat treatment, the hardness of samples was measured by special instrument, microstructure was also photographed to be analyzed carefully. through these experiments, we also debated on the theories which explain the new phenomenon occurring in laser overlapping treatment

    第二章：介紹了工業中的各種激光加工技術和激光加工系統，詳細說明了本實驗所使用的高功率激光加工系統；第三章：詳細敘述了激光淬火的機理和熱傳導數學模型；第四章：通過實驗，分析激光淬火后的模具鋼的硬化帶的硬度分佈及金相組織特性，同時對激光交疊熱處理的特點及形成機理都作了深入的探討。
  16. It is natural graphite as outstanding films phosphorus chemical processing, heat treatment, the non - pressure processing from any binder pure graphite products

    它是由天然磷片石墨經特出化學處理、熱處理、壓力加工而成的不含任何粘結劑的純石墨製品。
  17. In order to improve the formation and distribution of carbides and the resistance to oxidation of high speed steel during the procession of heat treatment, the content of w and mo should be limited and the content of v and nb should be en

    4 m復合變質處理的高速鋼fe衛ce v斗mo 5ocr刁0wi 5onb ，其熱處理組織中分佈著大量細小彌散的粒狀碳化物，碳化物網基本上得到消除。
  18. The paper describes the heat treatment at the temperature of 160, 250, 350, 400, 450 and 500, the dimension change and microstructural evolution of miniature fuel element plates after heat treatment. the result reveals that : the fuel plates did not deform after 60 days at 160 and 250, slightly curved after 60 days at 350 and 400, and heavily curved after 20 days at 450 and so did after 1 day at 500

    本論文介紹了微型燃料元件板（芯體u _ 3si _ 2 - al ，包殼為6061鋁）的熱穩定性實驗研究，在160 、 250 、 350 、 400 、 450 、 500溫度下經過一定的熱循環，測定燃料板的變形，進行微觀組織分析，結果表明：在160 400范圍四個溫度循環熱處理60天後，燃料板厚度變化均小於0 . 03mm ，在前兩個溫度下，基本沒有變形；在後兩個溫度下，燃料板稍有捲曲。
  19. Before heat treatment, the coating with low phosphorus content is harder than that with high phosphorus content and its abrasion - resistance is also better

    在鍍態下，低磷鍍層較高磷的非晶鍍層具有更高的硬度，其耐磨性能也顯著高於高磷鍍層。
  20. The optimal molar ratio of bzach was ti4 + : bzach = l : 0. 8, and the solvent was ethyl alcohol and de - ionied water. after heat treatment, the thickness of the thin films was about 70nm and the line width was 0. 5 urn

    用此溶膠制備bst凝膠膜，通過激光干涉制備了bst薄膜光柵，溶洗劑為乙醇十去離子水，圖形熱處理后的厚度約為70nm ，線寬約為0 . 5卜m 。
分享友人
分享到 Line

分享到臉書