heating section 中文意思是什麼

heating section 解釋
加熱部分
  • heating : adj. 1. 加熱的；供熱的。2. 刺激的。n. 1. 加熱；供暖；（建築物的）暖氣裝置。2. 白熾，灼熱。
  • section : n 1 （外科、解剖的）切斷；切割；切開。2 【外科】切片，【金相】磨石。3 （果子的）瓣。4 【數學】截...
  1. Using material, which composition is basically same to substrates through grinding, and then dipping its slurry on substrate with heating 800 and then sintering at 1400. there was no crack on the surface of coating. distinguish between coating and substrate may use sem, from sem micrographs of cross section of coating, there is gradated pore structure, while pore - forming agent is no good for coating

    採用與基體成分相同的原料配製的料漿在經800燒成的素坯上成膜，燒成后發現，添加成孔劑的料漿成膜后表面易於開裂，而未加成孔劑的料漿成膜效果較好。
  2. The welding technology of francis turbine runners is optimized from the view of subsection welding and local heating by numerical simulation. the result shows that welding residual tensile stress appears in the weld and its area nearby, and peak stress appears in the dangerous area of blades after practising quondam welding technology ; welding residual tensile peak stress in the dangerous area of blades can be decreased by welding both ends earlier and then welding middle section later during subsection welding, and decreasing effect on welding residual stress of the subsection welding is related to the weld length of blade outlets and welding direction of each subsection ; decreasing effect on residual stress of the local heating is direct proportional to heating time, heating temperature, heating area, and inversely proportional to cooling area, and welding residual tensile peak stress in the dangerous area is decreasing trend earlier, and then increasing trend later with heated location increased

    本文利用數值模擬手段對轉輪的焊接工藝從分段焊和局部加熱兩個方面進行了優化，結果表明:採用普通工藝焊接時，葉片焊后殘余拉應力出現在焊縫及其附近區域，並且在葉片出水邊的熔合線附近（危險區域）出現了峰值;在採用優化的分段焊時，先焊兩端后焊中間的方法可以降低葉片危險區域的焊接殘余拉應力峰值，降低效果與葉片出水邊焊段長度、焊縫各段的焊接方向有關;局部加熱法降低轉輪危險區域殘余應力的效果主要與加熱時間、加熱溫度以及加熱面積成正比，與冷卻面積成反比，並且危險區域的殘余應力隨加熱區域的增大呈先降低后升高的趨勢。
  3. Asme boiler pressure vessel code - section 4 : rules for construction of heating boilers

    Asme鍋爐和壓力容器規程.第4節:加熱鍋爐的建造規則
  4. Erection of low voltage installations - part 7 : requirements for special installations or locations - section 753 : floor and ceiling heating systems ; german version hd 384. 7. 753 s1 : 2002

    低壓設備安裝.第7部分:特殊裝置或位置要求.第753節
  5. Avoiding the difficulties of detecting the difficult parameters in furnace control and of building up the models, integrated with fuzzy control and conventional pid control, abb ’ s control it system is used to predict the bloom surface and center temperature directly based on the temperature of furnace wall easily to be detected so that the temperature settings in various furnace sections can be self - corrected, the furnace temperature of each section self - adjusted and on - line parameters of combustion control self - optimized. in addition, the heating parameters and the operating status of the field plant can be monitored with alarm

    採用abb公司的controlit控制系統，避開爐子控制中遇到的困難參數檢測及建模困難等因素，直接根據容易檢測的爐壁溫度來推知鋼坯表面溫度及鋼坯中心溫度，將模糊控制技術與常規pid控制相結合，實現各段溫爐設定值自修正、各段爐溫自協調、各參數在線自整定的自尋優最佳燃燒控制;對熱工參數、現場設備的運行情況進行監視、報警，實現爐膛壓力、管道壓力、換熱器的保護控制，並將重要參數送往廠級mis網路。
  6. For the pipe section with natural gas hydrates formed, several effective methods to treat ngh are suggested to use, that is, depressurizing as fast as possible ; heating the pipe ; injecting methanol / ethylene glycol and venting

    指出對已形成水化物的管道段，可採取盡快降低運行壓力、加熱、注醇和放空等措施進行處理。
  7. Instant heating device can automatically activate the shoe glue at the rear section of drying oven

    配備瞬間加熱裝置，可使後段烘箱自動活化膠化。
  8. Our main products include central material supply system, series drier, automatic charging machine, single double screw extruder, series heating and cooling blending machine, crusher, cold water machine, mould temperature controller, pipe, bar section, board, pp - r pipe, pe fuel pipe, plastic dual tubing extrusion production line and granulation completed production line equipment, at same time, we also carry on various plastic machine and refrigeration engineering. the products are sold well in every province and city of the whole country and also exported to about 30 countries and areas with strong technical force, advanced equipment, scientific management system and perfect after - sales service

    公司主要產品有集中供料系統系列乾燥機自動加料機單雙螺桿擠出機粉料高速混合機粒料混合機螺旋上料機牽引機切割機離心脫水機化纖團粒機全自動擴口機全自動計量混合裝置破碎機磨粉機冷水機模溫機管材型材板材pvc管材pp - r管材pe供水燃氣管材中空壁纏繞管材硅芯管材生產線，雙管擠出電工穿線管材造粒等全套生產線設備。
  9. No. of heating section of machine barrel

    機筒加熱段數
  10. No. of heating section of mold head

    模頭加熱段數
  11. Elements should have their heating sections in the furnace chamber so that no portion of the heating section extends into the furnace wall or refractory plug

    安裝時應確保其發熱部在爐腔內，沒有超出爐壁或者難熔插栓的部分。
  12. Double - deck stainless steel inner in heating section, and automatic radiator system fitting in sloww - cooling sect

    加熱段雙層不銹鋼內膽，緩冷段有自動散熱系統裝置。
  13. Asme boiler pressure vessel code - section 6 : recommended rules for care and operation of heating boilers

    Asme鍋爐和壓力容器規程.第6節:加熱鍋爐維護和操作的推薦規則
  14. Test methods for pigments - part 15 : loss on heating - section 2 : ignition residue

    顏料試驗方法.第15部分:加熱損耗.第2節:燃燒殘余物
  15. Bigger section area of three phase heating cable can broaden heat transmitting area and thisincreases the transmitting efficiency

    三相帶截面大，傳熱導面積大，能提高傳輸效率。
分享友人
分享到 Line

分享到臉書