height-width-depth 中文意思是什麼
height-width-depth
解釋
高（度）-寬（度）-深（度）-
Armhole depth sleeve cap height and width as well as sleeve cap curve arc the important factors in defining modern sleeve shapes
摘要袖勢是由袖窿深、袖山高、袖肥及袖山曲線確定的。 -
In this paper, high heat penetration into a moving particulate bed is described mathematically with a comprehensive heat and mass transfer model. the distribution of gas velocity and pressure, the temperature field of gas and solid in the moving particulate bed are examined for different conditions. the results show that thermal penetration into the moving packed - bed particles by fluid flow in porous media is high only in the position near the gas entrance. the thermal penetration thickness tends to increase with the fluid flow velocity and decrease with the particle moving velocity. in the region of thermal penetration, the porosity of solid bed has significant effect on gas field and pressure loss. it is feasible to reduce the gas pressure loss by a larger width / height packed bed in design and operation. the correspondence between thermal infection depth and particle bed height would be helpful to keep high oapacity of reactor and reduce the cost of operation
針對移動顆粒床中物料層內的高溫氣體滲流傳熱現象，考慮滲流與傳熱的相互作用，採用局部非熱平衡假設建立了多孔介質滲流傳熱物理數學模型並進行了數值計算.研究了不同情況下床內填充多孔介質中的流速、氣固溫度和床層壓力損失.計算結果表明，高溫熱氣對移動床顆粒料層的熱滲透主要發生在滲流入口端區域，增大入口滲流速度以及減小床層物料下移速度將導致物料溫度沿床高慢速下降，熱滲透深度擴大，熱滲透作用區域內的物料溫度水平提高.在熱滲透作用區域，孔隙率對流場和壓力損失有很大的影響.研究結果對于移動顆粒床反應器的設計與運行具有一定的參考作用 -
Connecting to the model test, some suggestions, important for design, are put foward, for example, the chute width of intermediate outlet should be constant ; the optimum height difference of drop between intermediate outlet and surface outlet should be larger than the water depth at intermediate outlet ; and the type of drop should be changed with the characteristics of certain project
結合試驗結果，提出中孔泄槽以等寬或微收縮為宜、表中孔最優坎高差應大於中孔水流的主流水深、跌坎形式的選擇應結合具體工程特點等建議。 -
These measures are as follows : shorten the primary wind intervals to improve thermal load of the burner ; reduce the size of hypothetical circle of contact to prevent the flame from splashing ; use nozzles with larger height / width ratio to increase the effusive rigidity, so as to increase the jet flow depth of secondary wind into the main jet flow ; use a higher primary wind velocity to increase its jet flow rigidity ; use a special flame holder structure of the primary nozzle, so as to improve
這些技術措施主要有:縮小一次風間距以提高燃燒器區域熱負荷;縮小假想切圓防止火焰刷墻;採用高寬比較大的二次風噴口以增加射流剛性，提高二次風射流進入主射流的深度;採用較高的一次風速來提高一次風射流剛性;一次風噴口採用特殊穩燃結構;提高下二次風的托粉能力。 -
Outer dimensions : height 35cm, width 56cm, depth 44cm
外盒規格35厘米高x 56厘米闊x 44厘米深
分享友人