hole blow 中文意思是什麼
hole blow
解釋
井噴-
The quality of furan sand castings is usually better than clay sand castings, however, some defects are also very easy take place with furan sand castings such as blow hole, metal penetration, veining, cracking, slag inclusion, hardness too low, surface recarburation, surface sulphuration, nodularity degeneration etc, which were usually caused by improper raw materials selection, improper method design, incorrect moulding or / and core - making
摘要呋喃樹脂砂鑄件質量一般比黏土砂鑄件好，但如果原材料選擇、工藝設計、造型和制芯操作不當，也會產生氣孔、粘砂、脈紋、裂紋，夾渣、硬度不足、滲碳、滲硫和球化不良等鑄造缺陷。 -
The results showed that the discharge coefficient of film cooling hole was greatly increased with the increase of blow ratio when the blow ratio m is lower, buta it had a little increase with the increase of m when m is larger
實驗結果表明，在吹風比較小時，隨吹風比的增加流量系數大幅度增加，當吹風比較大時，隨吹風比的增加流量系數增幅減小。 -
The whale expelled water from his blow hole
鯨魚從鼻孔排出水。 -
The ancient xiao was made up of 16 or 24 bamboo pipes of various lengths, each with a hole at the top for the player to blow. these bamboo pipes were then placed onto a bird - shaped stand, an instrument which we now call paixiao. the xiao has a soft and leaving tone, which makes it a suitable instrument for the performance of lyrical works
古代的洞簫用十六根或二十四根長短不同的竹管，管的上端開有吹孔，每根竹管只能發出一個音，把它們編排起來后便插入一具木製的鳥翼型座子上，這樂器現稱為排簫。 -
The reason and prevention of four kinds defects including surface wrinkled skin ( carbon built - up ), chock, blow hole, deformation, was introduced in this part of the article
本部分主要介紹表面皺皮（積碳） 、嗆火、氣孔、尺寸超差及變形等缺陷的產生原因和防止方法。 -
A big wind can blow through a small hole
針尖大的窟窿，斗大的風。 -
Or my friends will blow a hole in your heart
否則我的朋友會在你的心臟上打個大洞 -
Sun ordered his men to blow a hole through the solid marble thick - doors of the underground palaces by using explosive because it was impossible for them to open the doors otherwise
由於地宮的門是用很厚的大理石做的，非常堅固，孫殿英便命令軍隊用炸藥來炸，使大門被炸出一個大洞。 -
I breathe air through a blow - hole on top of my head. i can hold my breath under water. can you
我利用氣孔來呼吸，我可以在水中憋氣，你可以嗎？ -
Based on the analysis for the reason causing choke, shrinkage and blow hole defects at two 216 bosses of the main plate of the offset machine, the method to eliminate the casting defects by carrying out qc activities was described
對01膠印機左右大墻板的兩個216圓臺易出現嗆火、縮孔和氣孔缺陷的原因進行了分析，介紹了開展qc活動消除01膠印機左右大墻板鑄造缺陷的方法。 -
The simulation results show that the shaped degree is decreasing when the spinning temperature and intrinsic viscosity are increasing ; the spinning speed has little effect on the shaped degree when the pump mass throughput is constant ; the shaped degree is increasing with the increasing of pump mass throughput when the spinning speed is constant ; the cross air - blow conditions have much effect on the shaped degree ; the scope of shaped cegree is increasing when the aspect ratio of spinneret hole is increasing ; the shaped degree has obvious decreasing tendency in the small zone of spinning path and this decreasing became gently when the pump mass throughput is increasing
模擬的結果表明：扁平纖維的異形度隨著紡絲溫度及特性黏度的升高而降低；泵供量一定時，紡速對異形度的影響不大；紡絲速度一定，異形度隨著泵供量的增大而增大；吹風條件對異形度的影響較大；隨著噴絲孔的長寬比的增大，異形度增加的幅度也較大；異形度在紡程上較小的區間內有明顯的下降趨勢，並隨著泵供量的增加其下降的趨勢變緩。 -
About a half - hour before the deadline, a swat team used explosives to blow a hole in a classroom wall in hopes of getting a clear shot at him, but they couldn ' t see him through the gap, and they blew the door off the hinges to get inside, said lance clem, a spokesman for the state department of public safety
國家公眾安全部門發言人說，大約三點半的時候，一支特警隊炸開了一間教室的墻壁，希望能更好的瞄準莫里森，將他擊斃，但通過洞口仍無法看到他，於是特警隊就破門而入了。 -
Formation reason and prevention of blow hole on chilled surface of camshaft
凸輪軸激冷麵氣孔成因及防止方法的探討
分享友人