hole charging 中文意思是什麼

hole charging 解釋
炮眼裝藥
  • hole : n 1 洞，穴，孔；（衣服等上的）破洞；傷口；漏洞；窩，坑；水流的深凹處，（河道的）緩流窪。2 （獸的...
  1. Sonic wave analysis on uncoupled explosive - charging structure for damnification of hole wall rock

    不耦合裝藥爆破對孔壁巖石損傷破壞的聲波分析
  2. Under the condition of immovability of the charging area of blast hole, the increase of the blast hole compression modulus not only improved fragmentation results but also decreased the blasting ground vibration because of the minishing of burden

    在不改變單個炮孔負擔面積的條件下，增大密集系數可以改善爆破效果，同時由於抵抗線減小，爆破震動也有所降低。
  3. The fact that the drill hole openings are located under water complicates charging work.

    炮眼口位於水下，無疑會使裝藥工作復雜化。
  4. The paper researches the relations between blasting effect and blasting parameters, including diameter of drill, non - coincidence coefficient, hole spacing, hole row - spacing, cartridge diameter, charge per hole, density of line charge, charging structure and detonating manner, and how to adjust the blasting parameters to get the best blasting effect under the given geological condition

    本文在重慶市某高速公路合同段進行了現場預裂爆破試驗的基礎上，研究了炮眼直徑、不耦合系數、炮孔間距、炮孔排距、藥卷直徑、單孔藥量和線裝藥密度、裝填結構、起爆方式等爆破參數與爆破效果之間的聯系，以及如何在給定的地質條件下調整爆破參數獲得最佳的爆破效果。
  5. Pneumatic handling. tanks for bulk material transportation. charging hole and locking device

    氣動裝卸.散裝材料運輸罐車.裝料口和扣鎖裝置
  6. The method of strengthening the charging at the bottom of the blasting - hole is usually described in traditional teaching - books and blasting engineering, which is used to overcome resistance at the bottom

    傳統的教科書和工程爆破中通常是採取孔底超深加強裝藥或底部採用猛炸藥的方法，用以克服底部阻力，消除根底。
  7. According to the work principle, mechanical model theory and simulation analysis of the hydraulic control valve of the drilling tool, the optimal design parameters of the angle of center of circle of the high pressure hole of upside valve are proposed ; the influence of the charging and discharging lag times on palm supporting capacity is discussed ; and the theoretic basis of designing the control valve of the drilling tool is put forward in the paper

    通過對調制式旋轉導向鉆井工具液壓盤閥機構的工作原理、力學模型的理論和模擬分析，給出了上盤閥高壓孔圓心角的最優設計參數；討論了充液、泄液滯后時間對巴掌支撐力的影響，提出了調制式旋轉導向鉆井工具控制閥機械設計和控制的理論依據。
  8. Charging hole seat

    裝煤孔座
  9. During the deep - hole blasting for the excavation of guishan quarry for construction of baoquan pumped storage hydropower station, the blasting powder factor and the charging concentration of the blasting powder in the rock are reasonably controlled, and then the rate of blasting chunk is greatly decreased with the reduction of the working amount of the boulder blasting afterwards in conjunction with the suitable excavator and crusher etc

    摘要在寶泉抽水蓄能電站工程龜山料場開挖的深孔爆破中，合理控制了爆破單位耗藥量和炸藥在巖石中的集中度，最大限度地降低了大塊率，並結合使用適宜的開挖及破碎機械等措施，從而減少了二次爆破工作量。
  10. Application of bottom interval charging in deep - hole blasting

    底部間隔裝藥技術在深孔爆破中的應用
  11. Influence of different kinds of hole charging structue on explosion energy transmission

    炮孔不同裝藥結構對爆破能量影響的理論探討
分享友人
分享到 Line

分享到臉書