hub blade 中文意思是什麼

hub blade 解釋
轂狀磨石刀片
  • hub : n. 1. 【機械工程】（輪）轂，旋翼葉轂。2. 中心，中樞。3. （電器面板上的）電線插孔。4. 【機械工程】襯套；套殼；中軸殼。n. 〈口語〉丈夫〈husband 的縮寫〉。
  • blade : n 1 （殼、草等的）葉片，葉身，葉。2 刀片；（安全）剃刀刀片 （＝ razor blade）; 刀口，刃；刀，劍；...
  1. In order to investigate the unsteady flow frequency domain performances of an axial flow compressor at different mass flow, rotating speed and blade row spacing, plus inlet flow distortion, and considering aerodynamic characteristics and stability of the compressor, the low speed research compressor ( lsc ) at college of energy and power in nuaa is used to carry out the experiment studies. a large amount of test data has been gained through dynamic pressure transducers embedded in the stator blades at the tip, middle and hub section, then fast fourier transform algorithm ( fft ) is applied to calculate the frequency data

    為探討軸流壓氣機在工作流量、工作轉速及動?靜葉排軸向間距變化時的葉片排流場非定常頻譜特性變化規律，並耦合進氣畸變的影響，同時與壓氣機氣動性能和氣動穩定性相關聯，作者利用南京航空航天大學能源與動力學院的低速大尺寸軸流壓氣機（ lsc ）試驗器，採取在靜子葉片表面埋入動態壓力傳感器的實驗方法，對葉尖、葉中和葉根三個截面的動態壓力進行了測量，獲得了大量的可靠的實驗數據。
  2. The effect of leakage flow due to the upstream hub axial gap on the rotor performance and the mechanism of interaction between the hub leakage flow and the rotor blade passage flow were studied based on the numerical simulations of the flow fields of a transonic compressor rotor with upstream hub leakage

    摘要為研究壓氣機轉子上游葉根軸向間隙泄漏流對轉子性能的影響程度以及泄漏流與轉子流場之間的相互作用機制，對帶有葉根泄漏流的跨聲壓氣機轉子流場進行了數值模擬。
  3. The surface of propeller, hub and the vortex of blade is discreted by a number of small hyperboloidal quadrilateral panels with constant source and doublet distribution

    槳葉、槳轂表面和螺旋槳尾渦面採用四邊形雙曲面元離散，以消除面元間的間隙。
  4. Among others, one method to solve this problem is to install lead - lag dampers. the conventional configuration for installing dampers is to put them between blades and hub. in 1990s, eurocopter began to use the inter - blade dampers in ec155 which means to put every damper between two adjacent blades

    傳統的減擺器布置是槳葉-槳轂式;上個世紀90年代，歐直公司開始在ec155上使用葉間減擺器，減擺器不是布置在槳葉和槳轂之間，而是布置在相鄰兩片槳葉之間。
  5. The complex vortex system structure and shock wave system structure inside this rotor is obtained. wall flow patterns on the blade surface and hub surface are found out. the complex vortex system structure, such as horseshoe vortex, passage vortex, corner vortex and trailing vortex, and the interaction with shock wave system are researched. especially, the character of the tip clearance flow inside the rotor passage is revealed, and the interaction between shock wave and tip clearance flow near blade tip and the evolution of tip clearance flow are considered

    給出了葉片表面及輪轂面上的壁面流型，分析並揭示了轉子葉道內的馬蹄渦、通道渦、角渦、尾渦等復雜渦系及其與激波的相互干涉；特別是，分析並揭示了轉子葉道內頂隙射流的特點，得到了頂隙附近激波與泄漏流動的干涉形態及泄漏流動的發展，並著重給出了其與激波的干涉形態。
  6. The flight test of ec155 tells us that inter - blade dampers can work very well in stabilizing the system ; another advantage of this configuration is it can make the hub system simpler and reduce the drag of air to the hub which is very important for helicopters with 4 or more than 4 blades

    Ec155的飛行試驗證明，這種減擺器布置方式對提高穩定性效果明顯;這種布置方式的另外一個優點是可以簡化槳轂，降低其氣動阻力，對多槳葉（四片和四片以上）直升機有重要意義。
  7. A new aerodynamic design system developed by authors for draft fan with enhanced efficiency, suppressed noise, enlarged flux and high load. the new design system features : a twist regulation for vortex control is employed in designing to lessen the secondary flow loss in the blade tip and hub ; the feasibility and high efficiency of this procedure has been verified by the tests of the prototype fan ; a new computer - aided 3d blading is used to optimize the blade ; numerical inverse checking is adopted to enhance accuracy in designing and cut down the period of the designing and production. this design system can make the optimized blade with " forward inclination ", " inclining sweep ", " bending sweep ", to minimize the various secondary flow losses, to expand the steady working range of the fan, and to suppress the aerodynamic noise source

    本文通過對一種新型高性能礦用局部通風機的設計、製造及試驗全過程的綜述，展現了新的先進設計體系在民用通風機上的成功運用，其研製特點是： （ 1 ）在葉片氣動設計中為了降低葉根及葉尖區二次流損失，採用可控渦扭向規律設計，樣機實測的高性能驗證了這種方法的可行性和高效性； （ 2 ）在設計方法中採用較精確的數值反驗算，獲取最優設計方案，大大提高設計的準確性和成功率，並縮短了設計試制周期； （ 3 ）在設計過程中發展了計算機輔助三維葉片造型新方法，可以根據設計需要簡便快捷地對葉片進行「前傾」 、 「傾掠」或「彎掠」造型，這些造型對減小各種二次流損失、擴大穩定工況范圍和控制葉輪機氣動噪聲源起到了非常好的作用。
  8. Abstract : a new aerodynamic design system developed by authors for draft fan with enhanced efficiency, suppressed noise, enlarged flux and high load. the new design system features : a twist regulation for vortex control is employed in designing to lessen the secondary flow loss in the blade tip and hub ; the feasibility and high efficiency of this procedure has been verified by the tests of the prototype fan ; a new computer - aided 3d blading is used to optimize the blade ; numerical inverse checking is adopted to enhance accuracy in designing and cut down the period of the designing and production. this design system can make the optimized blade with " forward inclination ", " inclining sweep ", " bending sweep ", to minimize the various secondary flow losses, to expand the steady working range of the fan, and to suppress the aerodynamic noise source

    文摘:本文通過對一種新型高性能礦用局部通風機的設計、製造及試驗全過程的綜述，展現了新的先進設計體系在民用通風機上的成功運用，其研製特點是： （ 1 ）在葉片氣動設計中為了降低葉根及葉尖區二次流損失，採用可控渦扭向規律設計，樣機實測的高性能驗證了這種方法的可行性和高效性； （ 2 ）在設計方法中採用較精確的數值反驗算，獲取最優設計方案，大大提高設計的準確性和成功率，並縮短了設計試制周期； （ 3 ）在設計過程中發展了計算機輔助三維葉片造型新方法，可以根據設計需要簡便快捷地對葉片進行「前傾」 、 「傾掠」或「彎掠」造型，這些造型對減小各種二次流損失、擴大穩定工況范圍和控制葉輪機氣動噪聲源起到了非常好的作用。
  9. The hub leakage flows were modeled and calculated in two different ways : the flow fields inside hub axial gap were calculated together with blade passage flow in an integrated manner, and the leakage flows due to the hub axial gap were modeled as inlet boundary conditions

    計算時分別採用了兩種模化途徑，即耦合求解轉子上游葉根間隙內空腔與轉子通道內的流場，以及求解將葉根同間隙模化為進口邊界的轉子流場。
  10. The chinese clones typically use cheap plastic for the main rotor hub, main blade grips, frames and other critical parts

    中國復製品的典型是用廉價的塑膠做主要的轉軸轂，主漿夾片，框架和其他關鍵的部位。
  11. Abstract : concerning the models for discribing aerodynamic stability of axial flow compressor, the original model is one - dimensional, and it is reasonable for the onset of surge only. for the onset of rotating stall, there are just some two - dimensional models at published literatures. a three - dimensional aerodynamic of compressor has been presented in this paper. an aerodynamic stability model concerning radial disturbance of compressor is presented. the calculated results show that the occurrence of radial disturbance is related to the axial velocity disturbance, which has important effect on aerodynamic stability of compressor. the position of onset of stall, in blade tip or hub, is dependent upon the characteristics of blade element. the comparisons of calculated results predicted by 2d and 3d aerodynamic stability model have also been made in this paper

    文摘:軸流壓氣機的氣動穩定性模型，最初為一維模型，僅適用於描述喘振發作.對于旋轉失速發作，在公開文獻中有一些二維模型發表.本文提出了一類考慮壓氣機徑向擾動對失速影響的新的氣動穩定性模型.計算結果表明壓氣機的軸向擾動往往隨著徑向擾動的產生，徑向擾動的強度影響壓氣機的氣動穩定性，在葉尖還是葉根首先產生失速與壓氣機基元葉柵特性密切相關.本文對軸流壓氣機二維和三維氣動穩定性模型的計算結果進行了對比分析
  12. Concerning the models for discribing aerodynamic stability of axial flow compressor, the original model is one - dimensional, and it is reasonable for the onset of surge only. for the onset of rotating stall, there are just some two - dimensional models at published literatures. a three - dimensional aerodynamic of compressor has been presented in this paper. an aerodynamic stability model concerning radial disturbance of compressor is presented. the calculated results show that the occurrence of radial disturbance is related to the axial velocity disturbance, which has important effect on aerodynamic stability of compressor. the position of onset of stall, in blade tip or hub, is dependent upon the characteristics of blade element. the comparisons of calculated results predicted by 2d and 3d aerodynamic stability model have also been made in this paper

    軸流壓氣機的氣動穩定性模型，最初為一維模型，僅適用於描述喘振發作.對于旋轉失速發作，在公開文獻中有一些二維模型發表.本文提出了一類考慮壓氣機徑向擾動對失速影響的新的氣動穩定性模型.計算結果表明壓氣機的軸向擾動往往隨著徑向擾動的產生，徑向擾動的強度影響壓氣機的氣動穩定性，在葉尖還是葉根首先產生失速與壓氣機基元葉柵特性密切相關.本文對軸流壓氣機二維和三維氣動穩定性模型的計算結果進行了對比分析
分享友人
分享到 Line

分享到臉書