immersion resistance 中文意思是什麼

immersion resistance 解釋
耐浸漬性
  • immersion : n. 1. 沉浸,浸沒。2. 【宗教】浸禮。3. 【天文學】掩始。4. 專心。 immersion in study 埋頭研究。 immersion in thought 沉思。
  • resistance : n. 1. 抵抗,反抗,抗拒,抵禦;敵對,抵抗力,反抗力,阻力,【生物學】抗病性。2. 【電學】電阻;阻抗;電阻器。
  1. All wire and connectors used to buid the black dragon 2 is cryogenically treated in our proprietary cold fusion deep immersion process to structurally align and fuse the metallurgical molecular bond in the conductive metals for less noise and lower line resistance

    黑龍2型電纜含有的所有導線及連接器都經過我們獨有的冷聚變深浸過程處理,以改變導電金屬絲內部的原子鍵位結構,產生低電阻低噪音的效果。
  2. The strength and wear resistance of diamond drill bits for petroleum exploitation will be increased considerably when cast tungsten carbide is applied and adheres to the substrate firmly with cast tungsten carbide of 80 - 200mesh as the skelton and copper alloy as the soldering material in a process of non - pressure immersion

    石油鉆探行業用的金剛石鉆頭,用粒度為80 ? 200目的鑄造碳化鎢粉作骨架,採用無壓浸漬工藝,以銅合金作釬焊料,將鑄造碳化鎢與基體牢固結合,強度、耐磨性大大提高。
  3. The results showed the mass abrasion resistance of the wpc was not affected by the immersion time and the saltness of the artificial simulated seawater obviously

    研究結果表明:海水的浸泡時間和海水鹽度對塑木復合材料的質量磨損量均無明顯影響。
  4. Iso 2812 - paints and varnishes - determination of resistance to liquids - part 2 : water immersion methods iso 2812 - 2 : 1993 ; german version en iso 2812 - 2 : 1994

    顏料和清漆.耐液體性測定.第2部分:水浸法
  5. Paints and varnishes. determination of resistance to liquids. part 2 : water immersion method

    塗料和清漆.耐液體性測定.第2部分:水浸泡法
  6. Ship coatings - determination of resistance to salt water - salt water and hot salt water immersion method

    船舶漆耐鹽水性的測定鹽水和熱鹽水浸泡法
  7. Standard practice for testing water resistance of coatings using water immersion

    水浸漬法測試塗層的耐水性能的標準實施規程
  8. Common test methods for insulating and sheathing materials of electric and optical cables - part 2 - 1 : methods specific to elastomeric compounds - ozone resistance, hot set and mineral oil immersion tests

    電纜和光纜的絕緣和鎧裝材料的通用試驗方法.第2 - 1部分:彈性復合物專用方法.耐臭氧熱固及礦物油浸漬試驗
  9. Insulating and sheating materials of electric and optical cables - common test methods - part 2 - 1 : methods specific to elastomeric compounds - ozone resistance, hot set and mineral oil immersion tests

    電纜和光纜用絕緣和護套材料.通用試驗方法.第2 - 1部分:彈性化合物的專用方法.臭氧抗性熱固和礦物油浸漬試驗
  10. Coil coated metals - test methods - resistance to water immersion

    卷材覆層金屬.試驗方法.耐水浸性能
  11. Resistance spot welding in aluminum alloy was tested by ultrasonic immersion method with focusing probe

    摘要介紹採用水浸超聲聚焦回波檢測鋁合金電阻點焊焊核直徑。
  12. Aerospace industry. paints and varnishes. determination of the water resistance. method by immersion in de - ionized water

    航空航天工業.塗料和清漆.耐水性的測定.用去離子水浸漬法
  13. Complete, filled transport packages - method for determination of resistance to immersion in water

    滿包運輸包裝件.耐浸水性能測定方法
  14. Rubber and similar elastomers. resistance of tubes and pipes to the action of liquids by contact or immersion testing methods

    橡膠和類似彈性體.管材耐液體浸漬或接觸作用試驗方法
  15. Common test methods for insulating and sheathing materials of electric cables. part 2 : methods specific to elastomeric compounds. section one : ozone resistance test - hot set test - mineral oil immersion test

    電纜絕緣和護套材料通用試驗方法第2部分:彈性體混合料專用試驗方法第1節:耐臭氧試驗-熱延伸試驗-浸礦物油試驗
  16. Hot applied joint sealants - part 8 : test method for the determination of the change in weight of fuel resistance joint sealants after fuel immersion

    熱用接縫密封膠.第8部分:燃料浸沒后耐燃料接縫密封膠重量變化測定的試驗方法
  17. The coatings obtained by zinc immersion had higher corrosion resistance than without zinc immersion

    浸鋅比不浸鋅鍍層孔隙率低。
  18. Evaluating intergranular corrosion resistance of heat treatable aluminum alloys by immersion in sodium chloride hydrogen peroxide solution

    將鋁合金浸入氯化鈉和過氧化氫溶液中進行熱處理時抗晶粒間腐蝕的評定
  19. The unit shall be equipped with a built - in electrical junction box. electrical heating elements shall be screw - in, direct - immersion, resistance - type. element operation shall be controlled by a thermostat for each element

    這種熱水爐應該配置一個內置的電氣接線盒。電氣加熱元件應該螺紋擰進的,直接浸入式,電阻型加熱元件。每個加熱元件的工作應該由一個溫控器控制調節。
  20. Electric heating elements shall be screw - in, direct - immersion, resistance - type heating elements

    電氣加熱元件應該螺紋擰進的,直接浸入式,電阻型加熱元件。
分享友人