inclined section 中文意思是什麼
inclined section
解釋
斜截面-
From the analysis, some suggestion about joint rigidity design is put forward : 1. joint initial rigidity can be enhanced within the limited range when to increase end - plate thickness ; 2. the rigidity and ultimate moment can be enhanced obviously when to adopt the beam with inclined section or to add axilla at the connections between beam and column ; 3. withm the permissive construction condition, exteriorly extended end - plate inclinedly placed is suggested to be applied firstly ; 4. when the rate of joint rigidity to beam rigidity, that is called, is less than 0. 1, the joints can be regarded as zero - rigidity joints ; on the other hand, if is more than 26, it is rigid connection joints
採用斜截面梁並在樑柱交接處局部加腋能明顯提高節點剛度和梁的抗彎能力； 3在允許的施工條件下，應優先採用外伸式端板斜放節點，有利於提高節點剛度，進而提高節點的抗彎能力； 4節點剛度與其連接構件的剛度比值0 . 1時，可按鉸接節點設計； 26時，可按剛接節點設計。 -
Moreover, aiming at the location of inclined license plate, we have proposed the algorithm based on gray changing characteristic and orientation field. in this section, we discussed in detail the application of mathematical morphology operator in rough locating objective region and introduced the theory and realization method of orientation field. then we used it to detect inclined angel of objective region, finally we can precisely locate and emendate the inclined license plate based on detection result, and so we provided the favorable foundation for segmenting character
此外針對傾斜車牌區域的定位分割問題，提出了基於灰度變化特性和方向場計算的定位演算法，其中詳細討論了數學形態學運算元在目標區域粗定位中的應用，重點介紹了方向場計算理論和實現方法，並將其應用於目標區域傾斜角度的檢測，根據檢測得到的結果進行了傾斜車牌區域的準確定位和校正，為后續的字元分割打下良好的基礎。 -
In order to considering the affections of the adjacent zone out of the girdler section, the internal - forces of two end surface which were obtained by the horizontal shaft system analysis are exerted on each model respectively. moreover, the weight, cable force and prestressing forces including girder longitudinal, diaphragm transverse and inclined web vertical directions are considered
考慮到梁段以外附近區域的作用，在其兩端面上施加了由平面桿系結構分析所得的端面內力，另外，索力和預加力（梁縱向、橫隔梁橫向、斜腹板豎向）也施加在相應的位置，分析了箱形主梁在自重、索力和預應力作用下的空間應力效應。 -
The penstock for jinhe hydropower station is less in china, as it has a obliquity of 50 on the bending and inclined straight section in space ; for which the manufacture and installation are smoothly completed under the construction condition in the tunnel and the environment of alpine region with available construction method in combination of limited construction method for the key technical problems of the manufacture and installation of the penstock, which provides a reference for the constructions under the similar circumstance
摘要金河水電站壓力鋼管的空間轉彎和斜直段的50傾角在國內是比較少見的，針對鋼管製造、安裝的技術難點，在高寒和復雜的洞內施工環境中，結合有限的施工手段，採取有效可行的施工方法，順利完成了製造、安裝任務，對類似環境下的施工提供了一定的借鑒。 -
It is inclined to put the performance evaluation system aside since the system don ' t go down to section or individual and actually it is less related to reward system. 2. during the process of building the balanced scorecard, the important key success factors are obtaining the support from supervisor, explaining the details of the content and spirit of the balanced scorecard to the organizationstaffs, forming a cross - departments unit, gaining confidence and support of managers, tying in organization framework and human resource system, and being taken part by the whole members in the whole process
二、在平衡計分卡規劃及推衍的過程中發現，攸關平衡計分卡能否成功的重要關鍵因素有以下幾項：高階主管的支持、對組織全體成員詳細說明平衡計分卡具體的內容及精神、成立跨單位之推行小組、尋求主管級以上人員之信任與支持、組織架構與人力資源體系的配合及全員參與。 -
Fabrication of the box beam is divided into such parts as reinforcement, formwork, concreting, prestressing, moving and storing of beam, pipe grouting under pressure, end sealing of the beam, water - proof layer on the bridge surface system, protective coating etc. the paper makes description of effective box beam construction technology and workmanship which can be adopted in other projects, such technologies as : manufacturing and fixing of reinforcement, steel reinforcement fixing baseplate, web plate and top plate respectively and lifting the steel skeleton into form, requirements of design and manufacturing and way of utilization for dismantling - erection type formwork and hydraulic formwork, optimization of concrete ratio, concrete pouring process of two ends of beam in priority over the middle, in sequence of first baseplate followed by web plate and top plate at last, concrete pouring in inclined section and in horizontal layer, concrete vibration mainly by external vibrator in assistance with internal vibrator, methods and regulation for steam curing of concrete, dual controls over stress and strain to ensure quality of prestressing workmanship, construction method of effective beam moving by heavy - weight special moving facility, some regulations and key notes about construction of grouting under pressure, beam ends sealing, water - proof layer on the bridge surface system, protective coating
箱梁製造由鋼筋工程、模板工程、混凝土工程、預應力工程、移存梁工程、孔道壓漿工程、梁體封端工程、橋面防水層和保護層工程等施工環節組成。文中介紹的採用胎具製作和綁扎鋼筋，分底腹板和頂板分別綁扎並吊裝鋼筋骨架入模；拆裝式和液壓式兩種模板的設計、製作要求和使用方法；綜合考慮、優化混凝土配合比，混凝土灌注從兩端至中間、先底板、后腹板、再頂板的施工順序和斜向分段、腹板水平分層、附著式振搗為主、插入式搗固為輔的施工工藝，蒸汽養護的方法和規定；應力應變雙控制確保預應力施工質量的施工技術；採用重物移運器有效移梁的施工方法；壓漿、封端、橋面防水層和保護層施工的一些規定和注意事項等都是對箱梁製造行之有效的施工技術和施工方法，並可為以後類似施工作借鑒。 -
According to the new concrete code, the calculation formula are put forward concerning the load - carrying capacity during construction, the load - carrying capacity of cross - section bending, longitudinal shearing, the inclined - section shearing and part shearing during the application of the continuous composite floor slab, which provide the design proofs for the continuous composite floor slab
摘要根據新混凝土規范，給出了連續跨壓型鋼板與混凝土組合板施工階段的承載力計算公式及使用階段的正截面抗彎承載力、縱向水平抗剪承載力、斜截面抗剪承載力和局部抗沖切承載力計算公式，為連續組合樓板的設計提供了依據。 -
When the low - tropospheric mpv1 < 0, mpv2 > 0 or negative mpv2 intensify, sudden rainstorm will be inclined to happen. the rainstorm usually happens in the dense section of the negative isoline of mpv1. wind and pressure field on moist isentropic surface reveals that the interaction between cold air and warm air, it successfully explains the reason why " 8
濕等嫡面上風場和氣壓場直觀地揭示了暴雨區冷空氣擴散、暖空氣堆積及兩者在等嫡面上相遇，輻合上升產生暴雨的機制，它較好地解釋了8 . 11 」暴雨強度強，范圍相對較小的原因。 -
Based on the tests, the advised formula of normal section bearing capacity and inclined section bearing capacity of high strengthen concrete frame columns are put forward, and the limit of axial compressive ratio and the minimum stirrup ratio in the encrypted region which meet ductility requirement to c60 concrete frame columns are given
在試驗研究的基礎上，提出高強混凝土框架柱正截面和斜截面承載力計算的建議公式，且給出了滿足延性要求的c60混凝土框架柱軸壓比限值和箍筋加密區箍筋的最小體積配箍率。 -
With the help of this program, this paper does research on the moved backwards of the slide surface, lengthening the anchor section, the soil nail ' s total force, gets conclusion about relations between the soil nail ' s length and the slope ' s grade, height, soil ' s mechanical parameter ; relations between soil nail ' s total force and coulomb soil pressure. with the help of the large multiuse finite element program ansys, this paper analyzes the soil nailing in one - step ' s slopes, in two - steps " slopes, puts the emphasis on the axis force ' s distributing along the soil nail at each rows, the effect of both the excavating mode and the original slope figure to the axis force of the soil nail, the one another effect between the upper - step slope and the nether - step slope in the soil nail ' s axis force, gets conclusion about the design of soil nail at the first low, different slope body is the same with different excavating mode, the original slope figure has more effect to some than others because of the slope body, the reasonably design of the step width in two - steps slopes, the two - steps excavating and retaining has more virtue than the one - step ' s. through soil pressure analysis this paper does research on the differences and the links between the coulomb soil pressure theory and the rankin ' s, the vertical pressure at the slope surface when the slope surface is inclined and the retaining wall is rough, the soil pressure ' s distributing behind the panel, gets conclusion about the effect of both the slope body inner stability and the slope surface local stability to the soil pressure
通過分析比較，論證了對數螺旋線型比圓弧形作為邊坡的假設滑裂面具有較多的工程優點，並為此編制了一個採用極限平衡法分析土釘支護的fortran語言程序，以此作工具對滑裂面的后移、土釘錨固段的超長、土釘總力的大小等方面作了研究，得出了有關土釘的長度與邊坡的坡角、坡高、土體力學參數的關系、土釘總力與庫侖土壓力間的關系等結論；採用大型通用有限元數值分析程序ansys分別對採用土釘支護的一階邊坡、二階邊坡進行分析，重點是研究各排土釘的軸力分佈規律、開挖方式及原始邊坡形態對土釘的軸力的影響、上下階邊坡在土釘軸力方面的相互作用，得出了有關第一排土釘的設計問題、不同類型的土體應適用於特定的開挖方式、原始開挖出的邊坡形態對一些類型坡體的邊坡土釘支護有較大的影響而對另外一些影響不大、二階邊坡臺階寬度的合理確定、二階開挖及支護比一階時具有較多的工程優點等結論；通過土壓力分析對朗肯、庫侖兩種經典土壓力理論的區別與聯系、坡面傾斜及墻背有摩擦時的坡面豎向應力分佈、面板背土壓力的分佈形態作了研究，得出了邊坡支擋土壓力受坡體內部穩定與坡面局部穩定兩個方面的影響、土釘支護面板背土體中卸荷拱的存在對面板受力有利等結論。 -
Practice on bolt and steel mesh support in high inclined and large cross section gateway of
大斷面巷道錨網支護實踐 -
Calculation of ultimate bearing capacity for inclined section of concrete composite beam with two - stage uniformly distributed load
二次受力鋼纖維混凝土迭合梁斜截面承載力計算 -
It is identical between the effects of steel fiber on shear resistance of concrete at inclined section of beams and on tensile strength of concrete. 4
鋼纖維對梁斜截面上混凝土受剪承載力的增強作用與鋼纖維對混凝土抗拉強度的增強作用之間存在良好的一致性。 -
The objective function is the cost of anti - slide pile " s per meter ; the constraint conditions are the strength of anti - slide pile " s normal section and inclined section, the ratio of reinforcing design and the size of section in the design code ; the design variables are the height of section, the area of reinforcement and the amount of hoop. and the optimization model is solved by 0. 618 method
本文提出的優化設計方法，以樁單位長度的總造價為目標函數，以規范對單筋梁的正、斜截面強度，配筋率及截面尺寸等要求為約束條件，以樁截面高度，抗彎縱筋面積，抗剪箍筋數量等為設計變量，來建立優化模型，並用0 . 618法進行求解。 -
Testing methods for paints - part 9 : coating powders - section 2 : inclined - plane flow test
塗料的試驗方法.第9部分:塗料粉末.第2節:傾斜面流量試驗 -
The cable - stayed bridge of the hong kong section has a main span of 210m with a single inclined tower 158m in height. viaducts carry the approach roads to the bridges with piers at a typical spacing of 75m
香港側的斜拉橋主跨長度為210米，單柱式後仰索塔高158米，高架引橋跨距一般為75米。
分享友人