increase gear 中文意思是什麼

increase gear 解釋
增速傳動裝置
  • increase : vt 增加，增大，增多；增強，增進 （opp decrease）。 increase speed 增加速度。 increase one s pace ...
  • gear : n 1 【機械工程】齒輪，（齒輪）傳動裝置，齒鏈；排擋。2 〈古語〉衣服；甲胄與武器。3 傢具；財物，動...
  1. After canvassing the basic theories and methods of reliability and optimization design of the transmission system, analyze the designs of the v - belt transmission, arc cone gear and disk spring separately. it is propitious to raise efficiency, improve capability, increase reliability, and decrease cost and so on

    在研究了機械可靠性優化設計基本理論和方法之後，分別分析了v型帶傳動、圓弧錐齒輪、液壓卡盤碟型彈簧的可靠性優化設計，對其進行針對性的研究，並通過試驗對設計結果進行檢驗。
  2. Especially the generation unit consisted of high - speed generator and micro turbine without a gear box can largely reduce the system volume and increase the efficiency

    尤其是高速發電機與燃氣輪機直接相連組成發電機組，中間不帶減速機構，可大大降低系統體積，提高系統效率。
  3. It is 1 - 1. 5 times longer than common gear hobs. it can increase axial travelmotion of gear hobbing

    長度比一般滾刀長1 - 1 . 5倍，可增加滾削齒輪時的軸向移動量
  4. 3, during the process of the gear teeth meshing, the film shape and pressure distribution have little difference. but, the temperatures have the distinctive changes as the engaged position is varied, which means that the temperatures as the increase in the rate of slide to roll

    3 、在齒輪傳動嚙合過程中，壓力分佈和油膜形狀無明顯變化，但溫升隨嚙合位置的不同呈顯著變化，即溫升隨著滑滾比增大而增大;在單、雙齒嚙合交替處，摩擦系數達到極值，可達0 . 08 。
  5. We must gear the amount of products we make to increase in public demand

    我們必須使我們生產的產品數量與公眾需求的增加相適合。
  6. For cutting the composite lock gear with unequal tooth thickness, a study is made on the design method of gear sharper cutter with nonstandard parameter involute tooth profile and noninvolute tooth profile. the cutter tooth arrangement, the choice of teeth number of the cutter and the basic method of cutter design are discussed ; and a new method of choosing deflection factor by using limited area is presented. and the curve of relationship between rear angle on tooth crest and helical angle on tooth side of the cutter is given so as to give a basis for the gear sharper cutter to choose its parameters. to design nonstandard gear sharper cutter by adopting the method mentioned above will simplify the calculation and will increase the efficiency of design

    研究加工不等齒厚的非標準參數漸開線齒形，與非漸開線齒形復合的鎖閉齒輪插齒刀刀齒的排列、刀具齒數的選擇以及刀具設計的基本方法，介紹用限制區域選擇插齒刀變位系數的新方法，並給出刀具齒頂后角與側螺旋角的關系曲線，為插齒刀參數的選擇提供依據.結果表明，採用上述方法設計非標準復合齒輪插齒刀，可簡化計算和提高設計效率
  7. Abstract : in this paper, a kind of technological scheme for one - step precision forging spur gear with large module is put forward by using positive friction role. experiment, in which commercial pure lead is taken as test material, is done in the special die designed, and force vs. stroke curve is recorded. it is shown that positive friction role can efficiently make a contribution to the filling of the tooth cavity, but increase forming force

    文摘:針對大模數直齒圓柱齒輪，提出了利用積極摩擦一步成形的工藝方案，並用工業純鉛作為試驗材料，在設計的專用模具上進行試驗，記錄了力? ?行程曲線，結果表明：利用積極摩擦作用能夠有效地保證直齒圓柱齒輪精鍛時齒腔充滿，但同時增加了變形力。
  8. The curvature interference of the gear and the influence of radius of the mill - cutter, axial misalignment, and center distance on meshing are analyzed. based on these analyses, propose two methods to achieve point - contact : to change the radius of the mill - cutter and increase the center distance

    在分析了弧齒線圓柱齒輪的嚙合傳動不產生曲率干涉的條件和刀盤展成半徑、軸線平行度誤差、中心距對嚙合影響的基礎上，提出了點接觸弧齒線圓柱齒輪實現的兩種方案:調整刀盤展成半徑和增大中心距。
  9. 3. base on the numeric method of finite element, the influence of interrelated shift coefficient and tooth number z to bend intensity of gear is studied. with the increase of the tooth number, tooth root maximum pull stress decrease ; with the increase of the interrelated shift coefficient, tooth root maximum pull stress increase

    3 、基於有限元數值計算方法，分析了不同關聯變位系數和齒數z對齒輪彎曲強度的影響：隨著齒數的增大，齒輪最大拉應力減小；關聯變位系數越大，齒輪最大拉應力越大。
  10. So, it is of great importance to study multi - tooth meshing effect of three - ring gear reducer to disclose the essence of high loading capacity of three - ring gear reducer, increase loading capacity, minimize design parameters and reduce manufacturing cost

    因此，考慮三環傳動中的多齒嚙合效應對于揭示三環減速器大承載能力的本質、提高三環減速器的承載能力、縮小設計尺寸、降低製造成本具有重要的意義。
  11. In the past ten years, many experts have aimed at optimization design of gear transmission & counting its bonding load - carrying capacity in order to improve its carrying capacity, increase service life & reduce volume etc

    摘要近十年來，為提高齒輪傳動的承載能力、延長壽命、減小體積等，許多專家學者致力於齒輪傳動的優化設計、膠合承載能力計算、可靠性設計等工作。
分享友人
分享到 Line

分享到臉書