incremental control system 中文意思是什麼

incremental control system 解釋
增量控制系統
  • incremental : adj. 1. 增加的，增大的，增長的。2. 增額的。3. 【數學】增量的。
  • control : n 1 支配，管理，管制，統制，控制；監督。2 抑制（力）；壓制，節制，拘束；【農業】防治。3 檢查；核...
  • system : n 1 體系，系統；分類法；組織；設備，裝置。2 方式；方法；作業方法。3 制度；主義。4 次序，規律。5 ...
  1. When the governing valve was series - connected on the return oil - line in the metering - out control system, under the same flow area and the same adjusted pressure of relief valve, with the incremental quantity of step load, the pressure highly - adjusted capacity of the hydraulic cylinder chamber with piston - rod increased, meanwhile, it ' s time of rise, time to peak and the governing time all increased. at the same time, the pressure highly - adjusted capacity of the hydraulic cylinder chamber without piston - rod increased

    當出口節流調速系統的回油路上串接調速閥時，隨階躍負載的增加，在相同流量閥開度、相同溢流閥調節壓力的情況下，液壓缸有桿腔壓力p _ 2 （ t ）的超調量是增加的，上升時間、峰值時間以及調整時間也是增加的；液壓缸無桿腔壓力p _ 1 （ t ）的超調量是增加的。
  2. Regarding the hysteretic properties and time - varying of the system, the scan round performance of the controller, adopt incremental pid algorithm in constant - pressure controlling and combine it with the integral - separated dead - zone algorithm as appropriate for the situation of the measuring system and applies fuzzy self - tuning to control pid controller parameters

    由於系統的滯后時變性和控制器的循環掃描工作方式，恆壓控制採用增量式pid控制演算法，結合測量系統實際情況加入積分分離帶死區改進演算法，並對pid參數進行模糊自整定控制，設計了一種參數自整定模糊pid控制器。
  3. The electrical structure and mechanical structure of the non - ripple torque control system of brushless motor is almost the same as that of the control system of conventional brushless motor. the difference is that the non - ripple torque control system of brushless motor has a incremental encoder which the control system of conventional brushless motor has not, which results in a great change of control method

    永磁無刷電機無脈動轉距調速系統與傳統無刷電機調速系統在電磁、機械結構上基本一樣，所不同的是它在傳統無刷機控制系統的基礎上增加了一個增量式編碼盤，從而導致其控制方法有了比較大的改變。
  4. This system makes a breakthrough of traditional incremental motion control theories. it breaks the strict ambit between continuum and discrete, speed and position, rotation and step, the space vectors of stator magnetic field and rotor magnetic field are selected as the main control objects, incremental motion control and motion control are combined organically to make incremental motion control develop to large capability, high efficiency, high precision

    這其中的交流步進控制理論打破了傳統的增量運動控制思想，打破了連續與離散，速度與位置，旋轉和步進的嚴格界限，以定、轉子磁場空間矢量為主要控制目標，將增量控制與運動控制有機的結合起來，使增量控制向大容量、高效率、高精度方向發展。
  5. In the speed control system, because of the system ’ s low speed and high precision, incremental pid control algorithm is adopted. in the position control system, a dual mode control algorithm is designed, which can not only guarantee the rapidity in the position control, but also realize the small overshoot accurate positioning

    在控制系統的設計中，針對本系統轉速低、精度高的特點，在速率控制系統中，採用增量式pid演算法;在位置控制系統中，設計了雙模控制器，以保證系統定位過程的快速性和小超調精確定位。
  6. The thesis, in the probability analysis and computation, considers the failure history of space frames and trusses, adopts the bound criterion and algorithms on the base of system ' s critical strength, and introduces the soft self - adaptation control bound into the identification of dominant failure modes ; at the same time, with the incremental load method and differential equalized recursive method, computes the limit - state function of failure mode and probability index precisely under no leaking the dominant failure modes

    文中在可靠性分析和計算部分，考慮空間剛桁架結構系統的失效演化歷程，採用基於系統臨界強度的約界準則和約界演算法，將柔性自適應控制邊界引入失效模式識別過程；同時，用荷載增量法和微分等價遞歸演算法相結合，確保在嚴格不遺漏主要失效模式的情況下，快速準確地求解失效模式的極限狀態方程和可靠度指標。
  7. Accorded to the experimental research, under different flow area of flow valve and different adjusted pressure of relief valve, conclusion that the regulation of the pressure p1, p2 in the two cylinder chambers varied with the change of step load were as follows : when the throttle valve was series - connected on the return oil - line in the metering - out control system, under the same flow area and the same adjusted pressure of relief valve, with the incremental quantity of step load, the pressure highly - adjusted capacity of the hydraulic cylinder chamber with piston - rod decreased, meanwhile, it ' s time of rise, time to peak and the governing time all decreased. while the pressure highly - adjusted capacity of the hydraulic cylinder chamber without piston - rod increased

    通過試驗研究得出系統在不同的流量閥開度、不同溢流閥調節壓力（進口壓力）下，液壓缸兩腔壓力p _ 1 、 p _ 2隨階躍負載變化的規律：當出口節流調速系統的回油路上串接節流閥時，隨階躍負載的增加，在相同流量閥開度、相同溢流閥調節壓力的情況下，液壓缸有桿腔壓力p _ 2 （ t ）的超調量是減小的，上升時間、峰值時間以及調整時間也是減小的；液壓缸無桿腔壓力p _ 1 （ t ）的超調量是增加的。
  8. C. f. lu, c. c. liu, and c. j. wu, " an incremental model of battery energy storage system for load frequency control ", journal of chung - chou, vol. 7, pp. 209 - 222, 1994

    呂俊鋒，劉群章，吳啟瑞，蓄電池儲能系統于電力系統之應用，電力電子技術，第26期， 67 - 76頁， 1995年4月
  9. Permanent magnet synchronous motor ( pmsm ) step motion control for the electric actuator is a new actuator control system adopted incremental motion control theory

    永磁同步電動機步進控制的電動執行器是採用增量運動控制理論研製的新一代執行器控制系統。
  10. According to the structure characteristics and motion rules of the new type nursing robot, the close loop control system of this new type nursing robot is designed and made with the virtual instrument developing software labwindows / cvi, mcu, piezoelectric ultrasonic motor and high precision optical incremental encoder, which can make the robot reset and rotate by the predefined tracks. at the same time, in order to make the nursing robots used more widely where intensity, precision and price are not high, another control system is designed with the step motor, virtual instrument developing software labwindows / cvi, multi - function daq card pci1711, linear power amplifier. in order to use the nursing robots in acupuncture therapy, a simple finger is designed

    在對其結構特點和運動規律分析的基礎上，本文以虛擬儀器編程語言labwindows / cvi為軟體開發工具，以單片機為控制核心，以超聲電機為驅動元件，以高精度光電編碼器作為速度和角位移檢測裝置，實現了機械臂的復位以及預定軌跡的閉環控制系統的開發;同時為適應一些強度不大、精度要求不高的應用場合，也為降低成本，簡化控制裝置，推動新型護理機械臂短期內應用推廣的需要，以目前應用較為廣泛、控制技術較為成熟的步進電機為驅動元件，用labwindows / cvi開發環境、 pci1711數據採集卡以及線性功率放大器開發了一套控制系統，實現了手臂的復位、勻速運動以及預定軌跡的控制系統;為推廣護理機器人在針灸理療中應用，設計了簡單的手指機構並利用labwindows / cvi開發環境，以及智能材料驅動器? ?層疊式壓電驅動器，進行了手指的抓取以及對驅動對象的轉動控制。
分享友人
分享到 Line

分享到臉書