inductance voltage 中文意思是什麼

inductance voltage 解釋
電感電壓
  • inductance : n. 【電學】電感，感應現象；感應系數；（發動機）進氣。 inductance bridge 電感電橋。
  • voltage : n. 【電學】電壓，電壓量，伏特數。 the working voltage （電氣的）耐壓限度。
  1. This device realizes series resonance between high voltage inductance and tested capacitance. because of series resonance a higher voltage exists on the tested capacitance than the power ' s output. so a new ac high voltage test way to large capacity sample comes true

    該裝置以調頻的方式實現高壓電感和被試品電容的串聯諧振，從而在被試品上得到高於電源輸出端的電壓，即實現了以小容量電源對大容量試晶進行交流耐壓試驗的一種新方法。
  2. According to the quickly adjustable characteristic of the peterson coil grounding system, this dissertation proposes a new control strategy. when the system is in operation, the strategy can limit the series resonance over - voltage by using the off - resonance method. when fault occurs, the strategy can conveniently suppressing arc by rapidly adjusting the inductance value of the peterson coil to the point, which the resonance with grounding capacitance of the power network is occurred

    依據可控硅控制消弧線圈接地系統的快速可控性，一改傳統的電網正常運行時調節消弧線圈接近於全補償的預調諧方法，提出正常運行時採用脫諧方法抑制串聯諧振過電壓；故障時立即調節消弧線圈電感量達到與對地電容諧振，以利熄弧的新型調節原理和方法。
  3. And at this foundation through the dispersed domine analyse the paper makes a great emphasis on the application of computer aided design and simulation, then designs a series of apfc design and simulation software. this paper takes out a set of designation and simulation on base of actual circuit. the reliable result, output voltage and inductance current which are got from this software are the same as the actual value

    本文在對一系列apfc電路設計、模擬分析方法討論比較的基礎上，著重應用離散時域法進行了計算機輔助電路設計和模擬方法的應用探索，以此為基礎設計了pfcexpert功率因數校正電路設計、模擬軟體，針對實際電路給出了整個設計和模擬全過程，通過實驗驗證了該軟體所得到的精確穩態解、瞬態輸出電壓和電感電流，與實際電路輸出基本相同，所建立的電路模型重現了電路的運行過程，反映了電路的實際工作機理。
  4. Phase - shifted zero - voltage - switching pwm full bridge converter can realize zvs for the power switches with the use of the leakage inductance of the transformer and the intrinsic capacitors of the power switches, so it is used widely for medium and high power applications

    移相控制零電壓開關pwm全橋變換器利用變壓器的漏感和開關管的結電容可以實現開關管的零電壓開關，在中大功率的場合應用廣泛。
  5. The influence of stray inductance in the module circuit to turn - off transient over voltage of igct has been investigated systematically, the surge current calculation has been done by simulation, and the short circuit failure once occurred in experiment has been analyzed by computer simulation, reproduced the breakthrough failure happened in experiment by means of simulation

    充分利用計算機模擬的優勢，詳細分析了模塊電路雜散電感對igct關斷過電壓的影響，進行了短路浪涌電流計算，對試驗中發生的短路故障進行計算機模擬分析，重現了試驗中出現的誤觸發貫穿短路故障現象。
  6. Zero - voltage turn - on and zero - voltage turn - off in lagging arm and leading arm of soft - switching topology, working waveform of power transformer and process of rectifier and transition are presented in detail. the influence of resonant inductance of the power transformer, resonant capacitor and variation of load to the process of soft - switching are given

    主要對軟開關滯后橋臂和超前橋臂的零電壓開通、關斷過程，功率變壓器的工作波形及整流換流過程進行了詳細的模擬分析，並重點討論了逆變器的諧振電感、諧振電容以及負載變化對軟開關過程的影響。
  7. In order to eliminate the voltage oscillation caused by the reverse recovery of the rectifier diodes, a resonant inductance and two clamping diodes can be introduced to the primary side

    為了消除輸出整流管的電壓尖峰，可以在原邊加入一個諧振電感和兩個箝位二極體。
  8. Transitional feature of the arc and metal droplet in the welding process with steam shielded arc is investigated by means of analysing the waveforms of welding voltage and current under different welding regimes and it is found that there are two types of arc process behavor ? " arc starting - arc blowing out - short - circuiting " and " arc - starting - short - circuiting ". under the condition of constant diameter of welding wire and its feeding speed, the arc process behavor can be changed by adjusting the inductance of welding circuit as well as the voltage of power supply. if arc process behaves as alternative process of " arc starting - arc blowing out - short - circuiting " with minimum time duration of arc blowing out and maximum frequency of short - circuit transition, the welding process will be stable with less spatter and smooth weld bead

    通過分析不同焊接規范下的焊接電壓和電流的波形.研究了水蒸氣保護下電弧及熔滴過渡的特點，發現其電弧過程行為有「燃弧?熄弧?短路」和「燃弧?短路」兩種形式.在焊絲直徑和送絲速度一定的情況下，通過調節焊接迴路中的電感量和電源電壓，可以改變電弧的過程行為形式.若電弧過程呈「燃弧?熄弧?短路」交替進行，並且熄弧時間最短時，短路過渡頻率最高，在這種情況下，飛濺小，焊道成型好，焊接過程穩定
  9. The control tactics of space voltage vector are investigated, and the simplified algorithm which judges the sector location of reference vector and calculates switch operation time is put forward. by analyzing the current hysteresis control, the relation between switch frequency, and hysteresis bandwidth and input inductance of pwm rectifier is deduced. by applying instantaneous power theory, the principle of pwm rectifier power control is analyzed, and the direct power control by matlab toolbox through estimating active power and reactive power with virtual flux is realized, and the simulation results prove that it is correct

    對常用空間電壓矢量控制策略進行分析，提出了給定參考矢量所在區間判斷的簡化方法，以及電壓矢量作用時間的求取方法；分析了電流滯環控制策略，推導出開關頻率與滯環帶寬以及整流器輸入電感之間的關系；應用瞬時功率理論分析pwm整流器功率控制原理，通過虛擬磁鏈估計有功功率和無功功率，用matlab實現了直接功率控制，並驗證了該控制方法的正確性。
  10. In chapter 4, considering the features of high voltage transformer and the difficulties to make it, a reasonable design scheme with src was proposed, which efficiently reduced negative influence of distributing parameters of transformer on switching power supply and could completely utilize leakage inductance as resonant inductance

    第四章中分析了高頻高壓變壓器的特點及難點，提出了合理的串聯諧振變換器的設計方案，能夠完全利用變壓器的漏感作為諧振電感，有效地降低了分佈參數給高壓大功率開關電源所帶來的不利影響。
  11. The sieries product is suitable for the system with current 50hz - 60hz and the rated voltage of 3. 6kv 40. 5kv. it can be matched with other protective electrical equipment vacuum connection, loading switch etc. it can also be used as the overload or short circuit protection parts for high voltage motor, transformer, voltage mutual inductance attenuator and other power equipment

    本系列產品適用於交流50hz - 60hz ，額定電壓3 . 6kv 40 . 5kv系統，可與其它保護電器如真空接觸器，負荷開關等配合使用，作為高壓電動機電力變壓器電壓互感器及其它電力設備的過載或短路保護等元件。
  12. A novel cycloconverter - rype three - phase hf link inverter topology for soft - switching based on phase - shifted full - bridge mode is proposed, whose main advantages are as follows : under the conditions of d < i < and overlap - d, the switches of the leading leg are turned on at zvs and the switches of the lagging leg are turned off at zcs and all switches of the cycloconverter circuit are commutated in the overlapping mode in the interval of zero voltage, which makes the circuit realize soft switching to the utmost extent and reliably solve the problem of peak voltage caused by the storing energy of leakage inductance of hf transformer

    論文提出一種新型移相全橋軟開關周波變流型三相高頻鏈逆變器，電路的主要優點是：前級移相全橋的移相角控制在_ d _ i和_ （ overlap ） - _ d條件下，超前橋臂零電壓開通，滯后橋臂零電流關斷，並使周波變流器所有開關在零電壓期間重疊換相，使整機開關最大程度地實現了軟開關，並可靠解決了高頻變壓器漏感儲能引起的電壓尖峰問題。
  13. By compared with the simulation results and the experiment results, we come to the conclusions that : ( 1 ) circuit with assistant network can widen soft - switching extent in lagging arm, reduces duty - cycle loss on the secondary, diminishes switching dissipation of inverter spot - welding power source. ( 2 ) the range of resonant capacitor, the important factor to soft - switching process, not only affects zero - voltage turn - off of power switches, but also affects the range of zero - voltage turn - on of power switches. so resonant capacitors must be considered according to many aspects ; ( 3 ) it easily fulfils soft - switching condition in lagging arm as leakage inductance of power transformer increases, but bigger leakage inductance of power transformer increases opening dissipation of transformer and decreases efficiency of soft - switching inverter power source

    通過模擬結果與軟開關點焊逆變器試驗結果的對比分析，得到了如下主要結論：採用輔助網路可以完全拓寬全橋軟開關逆變器的滯后橋臂軟開關范圍，減小了次級占空比丟失，降低了逆變電阻點焊電源的開關損耗；諧振電容是影響軟開關工作狀態的重要因素，其大小不僅影響開關管的零電壓關斷，同時也影響開關管的零電壓開通范圍，因此，諧振電容應該綜合考慮；功率變壓器漏感越大，越容易滿足滯后橋臂的軟開關條件，但是大的漏感也使變壓器的通態損耗增加，降低了軟開關逆變器的效率。
  14. Initial recovery voltage and peak recovery voltage across the circuit - breaker have an essential affect on re - strike. for assessing performance of circuit - breaker, the higher inductance and lower inductance must be considered at the same time when testing according to theoretic analysis, the directly test circuit on switching the no - load overhead by high - voltage circuit breakers of rated voltage 252kv and below, in compliance with the correlative standard jb5871 and the test devices, and the test circuit parameters have been calculated and the many testes have been carried out

    在理論分析的基礎上，考慮實驗室現有設備的情況依據標準jb5871的規定，選用合適的試驗設備，對試驗線路的參數進行計算，在實驗室建立了252kv及以下電壓等級斷路器開合線路充電電流直接試驗線路，利用該線路進行了數臺產品的試驗，分析了試驗結果，並根據試驗結果和理論基礎討論了gb t1984 - 200 《交流高壓斷路器》 （報批稿）關于開合線路充電電流試驗的有關規定。
  15. Thesis this in existing electric capacity, whether it utilize by the ct one mainly reject and mix by suitable partial pressure not low - voltage partial pressure arm not high - handed of cvt electric capacity not insulating, in the middle of and ca n ' t compensate reactor, etc. of voltage transformer, design by sectional mutual inductor that ct combine cvt with, sectional mutual inductance utensil this have electric current mutual inductor and voltage double function of mutual inductor

    本論文在現有電容型絕緣電流互感器和電容式電壓互感器製造技術的基礎上，利用ct的主絕緣電容屏作為cvt的高壓分壓臂，配以合適的低壓分壓器、中間變壓器以及補償電抗器等，設計了由ct和cvt相結合的組合式互感器，該組合式互感器具有電流互感器和電壓互感器的雙重功能。
  16. Because of the clamping capacitor and the interleaved structure, it has some good features compared with other flyback converters, such as : the topology is simple and can be realized easily ; the voltage spike of the power switch is availably restrained and without leakage - inductance energy loss ; the ripple of the input and output current is reduced, correspondingly, the volume and weight of the output and input filter is also significantly reduced

    由於箝位電容的加入，相對于其他類型的反激式變換器電路，該拓撲具有一些獨特的優點:電路結構簡單且易於實現;無需另加輔助開關管，實現了開關管的有源箝位，抑制了開關管的電壓尖峰;提高了輸入、輸出電流的脈動頻率，減小了輸入及輸出濾波器體積。
  17. A new viewpoint to observe the relation of bus voltage, bus current injection and branch current of the network considering branch mutual inductance has been provided in this paper. the process of building the z - matrix of a large - scale power network is set forth in particular in this paper. and the method is employed in the fault computation system successfully

    本文為了從演算法上提高故障計算的速度，在完全計及支路互感的前提下，利用節點注入電流與支路電流以及支路電流與節點電壓的關系，提出了一種能夠統一處理互感和無互感線路、快速形成大規模電網節點阻抗矩陣的新方法。
  18. Some important parts for these two vsc - hvdc control systems are designed in detail, especially the structures and parameters of the vsc controllers, as well as the principles for selecting the equivalent inductance of the convertor transformer and the capacitance of the capacitor on the dc side of the vsc. digital simulation using netomac is done to verify the validity of those proposed control strategies. ( 2 ) the operation performance of the vsc - hvdc under some characteristic faulted conditions without any protection measures are studied, and the over - current and over - voltage of the vsc - hvdc during those faults is revealed

    （ 2 ）對vsc - hvdc在沒有保護控制的情況下其交流側、直流側和vsc內部等部位發生常見較嚴重故障時的運行特性進行了模擬研究，總結出這些較嚴重故障可能對vsc - hvdc造成的危害，並針對這些危害提出了幾種切實有效的保護策略，模擬結果證實了應用這些保護策略可確保vsc - hvdc中的一些重要部件能夠在大多數類型的故障時免遭過電壓或過電流的損害。
  19. ( 2 ) each state of the total switching period has been studied in detail, in which the voltage of block capacitor and current of leakage inductance of main transformer and keeping time of each state have been discussed, then the condition of zero voltage switching is attained, which gives theory guidance for setting reasonable dead time, finally, the possibility of zero voltage switching is proved by simulation of saber software

    （ 2 ）對不對稱半橋在一個完整的開關周期內各個狀態分析，描述了隔直電容電壓和變壓器漏感電流的變化規律，各個狀態的持，然後得出實現zvs的條件，從而為設置合理的死區時間提供了理論指導，最後用saber軟體進行了模擬，驗證了零電壓開關實現的可能性。
  20. On the bases of fea results and one - order constant coefficient nonlinear differential equations, a steady analysis method for the motor system ’ s running steadily is proposed. and a primary research work has been done on some steady characteristics of the system, such as phase current, field flux, inductance, voltage, output torque. all these are verified by some tests applied on prototype

    在有限元計算結果及系統模態方程的基礎上，構建了系統穩態運行模擬模型，對系統穩態運行過程中的電流、磁鏈、電感、電勢、輸出轉矩等穩態特性進行了初步的研究，並通過相關試驗進行驗證。
分享友人
分享到 Line

分享到臉書