inertial-mass 中文意思是什麼
inertial-mass
解釋
慣性質量-
Some conclusions are drawn : 1 ) effect of inertial force from superstructures on the lateral seismic response of single pile can not be ignored ; 2 ) the lateral seismic response of single pile induced by far - field earthquake are mainly affected by acceleration mass of superstructure > site eigenperiod. it increases with the increment of accele ration and mass of superstructure. as the site characteristic frequency approaches the self - oscillation frequency of the pile, sympathetic vibration occurs and the value of lateral seismic response reaches maximum ; 3 ) as the stiffness ratio of pile to soil increase, the relative displacement of pile to soil increases ; 4 ) the lateral seismic response of fixed - head pile is much smaller than that of free - head pile
將其解析解與具體的的抗震設防烈度和場地特徵周期結合起來，計算分析了成層地基中單樁的橫向地震響應，得到了以下結論： 1 ）上部結構慣性力對樁的橫向地震響應的影響不可忽略； 2 ）成層地基中的單樁的橫向地震響應主要受地震基本加速度、場地特徵周期、上部結構質量的影響，隨地震基本加速度、上部結構質量的增大而增大；場地特徵頻率越接近樁基自振頻率，樁基地震響應越大，等於自振頻率時，由於發生共振現象，樁基響應幅值最大； 3 ）樁土剛度比越大，樁土之間的相對位移的幅值越大； 4 ）樁頂固接的連接方式，可以有效地降低地震時單樁的橫向地震響應。 -
Inertial mass can be defined only in terms of certain mechanical measurements whose success hinges on newton's law of motion.
只有用某些力學上測量，才能給慣性質量作出定義，而這些力學上的測量的成就是隨牛頓運動定律而定的。 -
Abstract : it introduces the principle of graphite electrode abrading tool and develops the software and hardware of nc machine. this can detect the position of platform feed with great inertial - mass through photoelectrical encoder, the vibration magnitude of translation worktable with eddy transducer. based on these the machine parameters can be automatically regulate, and the grinding process is smooth
文摘:介紹了石墨電極研磨成形機的原理和數控軟、硬體系統的研製開發；用光電編碼器實現了大質量進給滑臺的位置檢測；並用電渦流傳感器檢測平動臺振動量，進而實現了機器參數的自動調整，從而保證了石墨電極研磨成形機研磨加工的順利進行。 -
According to the law of mass moment of inertia and of momentum moment, the conditions for the complete dynamic balance of rotor inertial forces and moment of inertia in the rotary piston vacuum pump are put forward, with the rotor movement in single cylinder analyzed as basis
根據質量矩定理和動量矩定理對單缸滑閥真空泵的轉子運動狀況進行了分析，分別提出了轉子慣性力和慣性力矩完全動平衡的條件。 -
This paper bring out design method of inverse eigenvalue problem, which adapts to general structures with linear parameters, namely coefficients of all or partial elastic component and inertial component are treated as design parameters, for given some order natural frequency and corresponding vibrating mode, all of useable designing parameters will be got through solving a linear system of equations, thereby stiffness matrix and mass matrix of actual structure are constructed. this paper also discusses existence condition and unique of results
提出了適用於具有線性參數的一般結構的逆特徵值問題的設計方法，即以系統的全部或部分的彈性元件與慣性元件的系數為設計參數，對于預先給定的若干階固有頻率及相應振型，通過求解一線性方程組即可確定全部實際可行的設計變量，從而構造出實際結構的剛度矩陣和質量矩陣，並論證了解的存在性與唯一性。 -
The solutions of maximum measurement range and the methods to increase the measurement are given in the condition of stable state and the restricted parameters. how to compensate dynamic performance of servo - system and the analysis of response of system in different inputs are given, too. in this paper the movement equations of the seismic mass of inertial sensor are derived by the known models of the accelerometer
主要包括：敏感質量偏心距、橫向加速度干擾和外加偏壓對傳感器穩定性的影響，給出穩定和參數受限條件下最大量程的求解以及提高量程的方法，研究如何補償伺服系統動態性能，以及不同輸入條件下系統響應的分析。 -
The mass matrix and the coupling matrix of bending and torsion vary with the time concern to the deflections of the system when the nonlinear inertial term and the geometric non - linearity term are comprised in the dynamic formulation
文中推導的動力學有限元方程中的一致質量矩陣m和彎扭耦合矩陣?都考慮了幾何非線性項和非線性慣性項，因此是與系統變形有關的時變矩陣。 -
The traditional designs of inertial sensors involve a solid proof mass or rotation part, which have some disadvantages such as low life, low reliability, difficult manufacturing and high cost
目前商用的慣性傳感器一般需要檢驗質量塊或者旋轉部件，因此，器件的壽命短、可靠性低、加工困難且成本較高。 -
The principal needs of realization on strategic inertial accelerometer are large measurement range ( higher than 70g ) and high stability. in this paper aimed at a most basic and typical " sandwich " structure with easy realization in techniques, the system of micromachined electrostatic servo - accelerometer is analyzed in detail on static and dynamic state, mainly including : the influence on the z - component of the center of mass, lateral accelerations disturbance and the applied bias voltage on the stability of the sensor
戰略慣導加速度計實用化的首要條件是大量程（ 70g以上）和高穩定性，本文針對一種最基本、最為典型和工藝上較易實現的「三明治」結構，從靜態和動態兩方面對電容式微機械靜電伺服加速度計系統進行了詳細分析。 -
Secondly, based on the defects of the uptodate balancing machine which were employed in the motorcycle manufacture plants, this dissertation has presented a new method on the means of checking unbalance mass of the motorcycle engine crank set. it has adopted the hard - bearing balancing machine as the prototype ， utilized tow group of resistance sensors placed in vertical direction with one another to pick up the information which stand for the inertial force of the motor engine crank set when it is running
其次，通過對當前國內外曲柄連桿機構動平衡實驗的現狀及其存在問題的分析研究，提出了一種新的測試方法：在工作原理上採用硬支承型測力式動平衡機，在測量方法上應用互成900的兩點測量來失量合成任意一點旋轉慣性力大小及方向，這也是也是其不同於以往試驗機的最大之處。 -
Secondly, based on the defects of the uptodate balancing machine which were employed in the motorcycle manufacture plants, this dissertation has presented a new method on the means of checking unbalance mass of the motorcycle single - cylinder engine crank - connecting rod mechanism. it has adopted the hard - bearing balancing machine as the prototype, utilized tow group of resistance sensors placed in vertical direction with one another to pick up the information which stand for the inertial force of the motor engine crank set when it is running
其次，通過對當前國內外曲柄連桿機構動平衡試驗的現狀及其存在問題的分析研究，提出了一種新的測試方法：在工作原理上採用硬支承型測力式動平衡機，在測量方法上應用互成90的兩點測量來矢量合成任意一點旋轉慣性力大小及方向，這也是其不同於以往試驗機的最大之處。 -
It introduces the principle of graphite electrode abrading tool and develops the software and hardware of nc machine. this can detect the position of platform feed with great inertial - mass through photoelectrical encoder, the vibration magnitude of translation worktable with eddy transducer. based on these the machine parameters can be automatically regulate, and the grinding process is smooth
介紹了石墨電極研磨成形機的原理和數控軟、硬體系統的研製開發；用光電編碼器實現了大質量進給滑臺的位置檢測；並用電渦流傳感器檢測平動臺振動量，進而實現了機器參數的自動調整，從而保證了石墨電極研磨成形機研磨加工的順利進行。 -
This dissertation has presented a new method on the measuring and checking procedures of the dynamic unbalance of the motorcycle crank and made a deep research on its measuring device. what have been done is as follows : firstly, the dissertation has thoroughly discussed the basic theory of rotor unbalance such as its varieties ， characters and rules of the movement which is under the excitation of the inertial force and inertial moment induced by the unbalance mass. it also has deeply expounded the dynamic mechanics of the specially formed components ? crank, especially in the area of the crank integrated with shaft and piston
本論文針對摩托車發動機曲柄連桿機構為研究對象，對曲柄連桿機構動平衡的測試提出了一種新方法，並對其數字化測試裝置進行了深入研究，完成的主要工作及取得的成果如下：首先，對動平衡理論進行了詳細的探討，論述了不平衡產生的原因，不平衡種類及轉子在不平衡量產生的慣性力激勵下的運動規律，並對曲軸這一結構特殊的剛性轉子的平衡理論進行了闡述，重點研究了曲柄連桿機構這一往復式機械構件的力學特性。 -
This dissertation has presented a new method on the measuring and checking procedures of the dynamic unbalance of the motorcycle single - cylinder engine crank - connecting rod mechanism and made a deep research on its measuring device. what have been done is as follows : firstly, the dissertation has thoroughly discussed the basic theory of rotor unbalance such as its varieties, damages, characters and rules of the movement which is under the excitation of the inertial force and inertial moment induced by the unbalance mass. it also has deeply expounded the dynamic mechanics of the specially formed components - crank shaft, especially in the area of the crank - connecting rod mechanism
本論文針對摩托車單缸發動機曲柄連桿機構為研究對象，對曲柄連桿機構動平衡的測試提出了一種新方法，並對其數字化測試裝置進行了深入研究，完成的主要工作及取得的成果如下：首先，對動平衡理論進行了詳細的探討，論述了不平衡產生的原因、危害，不平衡的種類及轉子在不平衡慣性力激勵下的運動規律，並對曲軸這一結構特殊的剛性轉子的平衡理論進行了闡述，重點研究了曲柄連桿機構這一往復式機械構件的力學特性。 -
It is a remarkable fact that the inertial mass of all bodies is, within experimental accuracy, proportional to the gravitational mass.
值得注意的是，在實驗的準確度內，所有的物體的慣性質量與引力質量都成正比。 -
With synthesizing the relevant other internal and external researchers " the achievements of theory and the results of experiment, the follow work have been done in this project : revising the formulas of ground stiffness coefficient and the mass of vibrating soil and the dynamic affecting degree of depth, which apply the theory of elastic half - space and the knowledge of the soil mechanics and consider the influence of the soil characteristic and inertial action, the interaction between foundation and ground, the diverse load ; making the model of ground and foundation system calculating natural frequency by using the big - scale software supersap which is for special purposes of finite element analysis ; according to the experiment analysis, correcting and adjusting the finite element model in order to have it accord with the fact and meet the engineering demands ; doing the vibrating experiment for testing the results of the theoretical analysis and the finite element calculation ; summing up some regulars of the ground stiffness
本文綜合參考了國內外其他學者的理論成果和實驗結果，進行了如下研究工作：運用彈性半空間理論和土力學的知識，考慮土體特性和慣性作用、基礎與地基的相互作用以及不同荷載形式等因素的影響，對動力機器基礎進行了嚴密地理論分析，修正了地基剛度、參振土質量和動力影響深度的計算公式；利用專門用於有限元計算的大型分析軟體supersap對地基基礎體系進行了建模計算，根據實驗分析，對有限元模型不斷地進行修正和調整，使其更加符合實際情況，滿足要求；通過振動實驗對理論分析和有限元計算結果進行了驗證；總結出了一些地基剛度的變化規律。 -
Abstract : the inertial effect of three - point bend specimens under impactloading was analyzed by using the spring - mass system model and an expression for the correction of inertial force was obtained under the condition of brittle fracture of materials
文摘:用彈簧質量模型分析了三點彎曲試樣在沖擊載荷作用下的慣性效應，得到了脆性斷裂條件下有效載荷的修正公式。
分享友人